Installing vacuum valve to housing Remove the plug of the M14 accessory port from the housing. Remove the cap from the vacuum valve. Tighten the vacuum valve to the housing with the tool provided. Building up vacuum Remove the cap of the vacuum valve. Connect the hand pump to the valve and pump several times until it reaches the target vacuum level. The LED light will turn flashing yellow while vacuum is building up, then steady green when the target vacuum level is reached. Attention: After the target vacuum is reached, i.e. steady green light, attach the cap back to the vacuum valve. It is recommended to leave the housing for at least 20mins to ensure it is sealed. If the LED light changes from steady green light to rapidly flashing yellow light, that means there is a leakage and please check every O-ring and conduct the vacuum test again. Please ensure that the cap is attached back to the vacuum valve before going underwater. Vacuum can be released by pushing the red release button. Attention: Please DO NOT attempt to go over the designated vacuum level, i.e. stop pumping when the LED turn green. Excessive vacuum level may lead to the malfunction of the camera and lens. Note: Although the vacuum indicator is designated to compensate for a certain amount of temperature variation, it is recommended to conduct the vacuum test in an environment where the temperature is stable. After set up, the meaning of the LED indicator in the housing: Flashing “Blue” light: Standby mode. The moisture alarm is active, and the system is ready for vacuum indication whenever a vacuum is detected. Flashing “Red” light with beeping sound:Moisture is detected. Flashing “Yellow” light: Some vacuum is detected, target vacuum level is not reached. Steady “Green” light: Target vacuum level is reached. Rapidly flashing “Yellow” light: Vacuum is dropping. (Will occur only after target vacuum level is reached) Rapidly flashing “Red” light: Vacuum is totally lost. Circuit stalled until switched off. (Will occur only after target vacuum level is reached)

Versatile shutter release extension by POP-UW With many underwater housings it is difficult to operate the shutter once the housing is mounted on a grip rail. This Universal Shutter Extension provides a remedy. With a marine stainless steel mounting plate, it attaches to a handle and allows you to operate the shutter release with your index finger - without the hassle of reaching around. The hand can remain on the handle. This way you also avoid unnecessary shaking.

With this spiral cable you can securely fasten your equipment to the D-rings of your diving waistcoat. Note: Not suitable for cave photography as the connection cannot be cut with a knife or cutter.

With this spiral cable you can securely fasten your equipment to the D-rings of your diving waistcoat. Note: Not suitable for cave photography as the connection cannot be cut with a knife or cutter.

Caps for housing connections of fiber optic cables to protect the transmission surface during storage and transport or when fiber optic cables are not used.

These caps made of CNC-machined POM plastic are suitable for all of our housings that are equipped with stainless steel pushers. They increase the contact area and thus make it easier to operate the pusher with gloves. Contents: 3 pcs., black and/or red colored, color is not selectable

Dieses 200 mm lange HDMi (D-D) Kabel ist für den internen Anschluss von dem HDMI-Anschluss des Gehäuses an den HDMI-Ausgang Kamera vorgesehen. Dieses Kabel passt u.a. zu folgenden Unterwassergehäusen von Nauticam: NA-XT2 NA-XH1 NA-A6400

With this spiral cable you can securely fasten your equipment to the D-rings of your diving waistcoat. Note: Not suitable for cave photography as the connection cannot be cut with a knife or cutter.

This 34 cm long carrying strap can be securely fastened with the supplied shackles and allows the housing to be easily lifted.

Lanyard in double color red and black made in Cordura fabric. It allows to lift up and carry the housing in a safe way while travelling or on a boat. It attaches easily to the housing handles thanks to two sturdy stainless steel snap hooks.

The HDMI cable is equipped with the typical M24 and M16 connector and is ideally suited for WED5 and WED-7 Pro underwater monitor. 

Extension for shooting right side for easier use. Easy to install and usable with all Isotta Compact housings. NOT suitable for Canon PowerShot G7X, G7X Mark II and GoPro Hero4 Silver.

This 23 cm lanyard attaches securely to the supported handle brackets with the carabiners provided, allowing the housing to be lifted easily and safely. 

Adapter for mounting the T-HOUSING to a standard GoPro mounting. CNC-milled POM plastic with two stainless steel screws. Extremely solid and high quality.

Easy and intuitive way to use ?Lights system for the passages of the vacuum Closing cap secured to the Vacuum bulkhead ?One hand vacuum pump Release of internal pressure by traction Electronics with pressure detection System

The HDMI-DA-C2 cable is used inside the underwater housing.

This 34 cm long carrying strap can be securely fastened with the supplied shackles and allows the housing to be easily lifted.

This is an HDMI cable for use inside supported housings to convert Type D to Type A HDMI connections with a length of 220mm.

With this spiral cable you can securely fasten your equipment to the D-rings of your diving waistcoat. Note: Not suitable for cave photography as the connection cannot be cut with a knife or cutter.

The LCD Magnifier uses a specially designed underwater +10 achromatic optic and features a dioptric adjustment so the user can dial in the lens correction to get a very sharp view of the camera LCD. The molded rubber sunshade virtually eliminates problems seeing the LCD in bright sunlight.

For use with the Nauticam Universal Fiber Optic Cable.  Provides connection to Nauticam housings with threaded optical cable bulkhead.

The mounting rails are required to attach the LCD enlarger to the following Nauticam underwater housings: -NA-RX100III -NA-RX100IV -NA-RX100V -NA-RX100VI -NA-LX10/NA-RX100III NA-RX100IV NA-RX100V NA-RX100VI NA-LX10/15

Protect the glass of Seatouch 4 Max housing  from being scratched underwater Packing including Wet&dry dust-free fabric Protective film Cleaing fabric  Dust absorbing stickers 

The HDMI-DD-C1 cable is used inside the underwater housing to connect your camera to the monitor.