HDMI 2.0 Cable M24D1R205-M28A1R170

FUJIFILM X-T3 The Fujifilm X-T3 features an APS-C CMOS 4 X-Trans 26.1MP Sensor. The X-T3 is powered by an upgraded X Processor 4 that is 3x faster and allows for 1.5x faster sensor readout than the X-T3. The base ISO has been lowered from 200 to 160. Oversampled DCI or UHD 4K (using full sensor width) is possible at 30p whereas 60p can be recorded with a minor 1.18x crop. The 60p footage can be captured as 10 bit 4:2:0 H.265 at 200 Mbps and recorded internally. This increases to 4:2:2 when output over HDMI. The X-T3 also features F-Log capture to maximize dynamic range, protecting highlights and shadows for editing. The X-T3 features a Natural Liveview mode when recording F-log that more closely resembles a standard monitoring LUT. Zebra warnings and focus peaking overlays as well as magnification during shooting are all improvements that video shooters will appreciate. Three custom white balance slots are available in addition to the 7 presets. The electronic viewfinder of the X-T3 is vastly improved with 3.69M dots as compared to the 2.36M dots of the X-T2. Battery life has also been improved. The X-T3 can achieve 20fps continuous shooting with Autofocus and this increases to 30fps when shooting from a 1.25x crop area. A Sport Finder mode will show this cropped area inside the EVF. Phase-detection autofocus has been increased to 98% of the sensor area. The X-T3 also features a fast 1/250 X-sync speed. Key Camera Specifications 26MP BSI 'X-Trans CMOS 4' sensor 425-point hybrid AF system 20 fps shooting with AF (11 fps with mechanical shutter) 3.69M-dot electronic viewfinder 10 bit 4:2:0 H.265 internal video capture (4:2:2 over HDMI) UHD/DCI 4K/60p from 1.18x crop region UHD/DCI 4K/30p using full width of sensor Internal F-Log capture Dual UHS-II SD card slots USB C-type connector can be used for charging battery THE NAUTICAM NA-XT3 UNDERWATER HOUSING Nauticam has supported X-T1 and X-T2 cameras and continues to create innovative and ultra-functional housings for this line with the NA-XT3. More than just an updated badge, the NA-XT3 is a complete redesign of the series. With a form factor more closely resembling the NA-A9 for Sony's A9 mirrorless camera, the NA-XT3 features DSLR-style housing and port lock mechanisms as well as integrated ergonomic handles. An optional hand strap (NA28130) can be added to the handles. The housing is designed with our Mission Control concept of placing the most important camera controls as close to the handles as possible to facilitate effortless and quick camera operation to ensure you don't miss the shot. The NA-XT3 features thumb levers near both handles, with the left thumb lever actuating the playback function and the right thumb lever the AF-L control. The housing includes two M14 and one M24 bulkhead openings and an M5 threaded hole on top (underneath the cold shoe) for an additional ball mount. The NA-XT3 uses the N100 Port System shared with the Fujifilm XH1 system. A selection of port options are available for a variety of lenses. VIDEO RECORDING FEATURES The impressive video specs of the X-T3 prompted the addition of some video-centric features to the NA-XT3. The base of the housing can accept Nauticam's Mounting Ball Set for Tripod (PN 25218), the same part as for the NA-A9. As the X-T3 can output DCI/UHD 4K at 60p with 4:2:2 quality over HDMI, a new M24 bulkhead has been incorporated into the housing to support an HDMI 2.0 connection to the Nauticam Atomos Ninja V housing (HDMI 2.0) for Atomos Ninja V 5” 4Kp60 4:4:2 10-bit Recorder/Monitor/Player (17922). Video shooting can decrease battery life so the NA-XT3 is compatible with an optional 2500 mAh USB-C Battery Pack (NA36335) that sits below the camera tray inside the housing. FLASH TRIGGERING Reliable automatic flash exposure is available with the NA-XT3 and a variety of optically fired flashes, precisely reproducing the camera’s included EF-X8 flash at a proportionally greater intensity. This system yields accurate automatic TTL flash performance – even in manual exposure mode – with no electrical sync cables to flood! The NA-XT3 is also compatible with the Nauticam Mini Flash Trigger for Panasonic/Fujifilm (PN 26305). The Flash Trigger allows for rapid fire manual flash firing via fiber optic, with no camera battery drain. The NA-XT3 comes fiber optic ready and accepts standard Sea & Sea style bushing connections. Nauticam Universal fiber optic cable system (NA26216) for Inon, Sea&Sea strobes, provide exceptional light transmission for accurate TTL performance. INTEGRATED VACUUM CHECK AND LEAK DETECTION SYSTEM The Nauticam vacuum check and leak detection system is pre-installed in the NA-XT3 as standard equipment. Combined with an optional M14 Vacuum Valve II (NA25624), this monitoring system provides constant updates throughout the dive as to watertight integrity of the housing via a multi-color LED on the rear of the housing.Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book.

THE CANON EOS R5C CAMERA The Canon EOS R5C is the latest in Canon's full-frame mirrorless camera lineup which has gained unprecedented demand.  It features the RF lens mount which has the same large 54mm diameter but the ability to have larger rear lens elements that are closer to the sensor gives increased corner and outer edge sharpness.  The R5C uses an all new 45MP CMOS sensor with in-body image stabilization which can reduce shake by up to 8 stops.  The camera's Dual Pixel autofocus system uses 1053 autofocus points across the entire frame.   It is also capable of recording 8K video at 24p or 30p and 4K at up to 120p.   The EOS R5C can also use the large EF-mount lens lineup via three optional adapters, a simple EF to R adapter, one which supports the customizable control ring and another that features a drop-in filter mount. Key Camera Specifications 45MP full-frame Dual Pixel CMOS sensor 8K Video, with option for RAW or 10-bit 4:2:2 C-log or HDR PQ Up to 4K/120p, or oversampled 4K up to 30p 100% coverage Dual Pixel II AF system 12 fps / 20 fps burst (mechanical / electronic shutter) 5.76M-dot OLED EVF with 120fps max refresh rate 3.2" 2.1M-dot fully articulating touchscreen 10-bit HDR photos in HEIF format 1x CFExpress slot, 1x UHS-II SD slot Weather sealing   THE NAUTICAM NA-R5C UNDERWATER HOUSING FOR THE CANON EOS R5C CAMERA The NA-R5C underwater housing follows suit with Nauticam's drive for innovation. Both the Canon EOS R5C and EOS R present shooters with the ability to use both the available legacy EF lenses via an adapter in addition to their native RF optics.  To support both the legacy and native lenses, Nauticam has integrated the NA-R5 into the N120 port system. Canon's EF to RF mount adapters can be affixed to the camera before insertion into the housing. When using the EOS RC5 inside the housing with the adapter and a supported EF lens, the port and extension ring arrangement will be identical to the same setup on a Nauticam Canon N120 DSLR. As the RF lens lineup emerges, dedicated port and extension ring combinations will be listed on the Port Chart. Two lens release buttons, one for RF and one for EF lenses used with the optional Canon adapter, are located on the front of the housing to make lens removal through the port opening simple. Mission Control Nauticam engineers are obsessed with getting the underwater image maker unfettered access to all the necessary controls, with as many within easy reach of the ergonomic rubberized handles. This Mission Control philosophy extends to the NA-R5C where a dual thumb lever and dual sub-lever are placed by the right handle. The upper thumb lever activates the "AF-On" and the lower the "Q" buttons while the sub-lever corresponds to the "M-Fn" and "Record" buttons. Near the left handle is a thumb lever for "Playback" as well as a dedicated switch to change from using LCD to the EVF. Large knurled and rubberized control dials access the camera's "main" and "sub" command dials. The two-stage trigger allows for smooth focus and firing activation. Additional buttons for "Menu", "Focus Point Selection" and others are also easily reached from the handles. An additional control wheel is located on the left side of the housing and will interface with the control ring on the supported EF to EOS R Mount Adapter with Control Ring using the optional gear (NA19561). Flash Triggering Flash triggering is achieved via one of two optional Flash Triggers, a manual LED trigger (NA26301) or a TTL Flash Trigger (NA26321) that use the built-in fiber optic bulkheads with optional fiber-optic cables to trigger supported strobes. For controlling strobes that do not support fiber optic flash triggering, a variety of legacy hot-shoe flash control bulkheads are available. INTEGRATED VACUUM CHECK AND LEAK DETECTION SYSTEM The Nauticam vacuum check and leak detection electronics are shipped with the NA-R5C as standard equipment. Combined with an accessory vacuum valve this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

THE CANON EOS R3 CAMERA The Canon EOS R3 in all respects appears to be the mirrorless sibling of the 1DX Mark III DSLR, clearly aimed at fulfilling many of the same roles while offering some additional capabilities through the use of the electronic viewfinder and the larger RF lens mount.  The full-frame 24.1MP Stacked CMOS sensor, in addition to having incredible low-light performance, can also capture full-width 6K video in both Raw and compressed formats at up to 60fps.  The R3 is paired to Canon's industry leading Dual Pixel AF system with 100% frame coverage and the now revived Eye AF system. DUAL PIXEL AF II Canon's Dual Pixel autofocus system has long been a favorite of underwater users, especially when it comes to tacking subjects.  With the R3, the system adds an additional 'Animal' recognition mode which might make the system even more reliable at following moving subjects.  Frame coverage is 100% with 1053 zones to ensure accurate focus wherever the subject may be. LOW LIGHT PERFORMANCE The ability to increase a camera's ISO with little penalty is of critical importance to underwater shooters for both stills and video as shooting with higher F-stop values delivers sharper corners and higher shutter speeds mean less motion blur.  The higher video frame rates also benefit by allowing the shooter to maintain a 180º shutter while still maintaining adequate aperture values.  When using color correction filters, which can often remove more than a full stop of light, compensation via ISO is not as much of an issue for overall image quality.  Maintaining dynamic range, even at high ISO levels is also important for those shooting still images using natural light or in poor water conditions. ENHANCED CONTROLS The R3 features an additional control wheel located at the upper right rear of the camera which doubles as the mode control.  This wheel can be assigned a variety of functions such as ISO and is adjusted by a dedicated control wheel on the housing within easy reach of the right handle.   VIDEO CAPABILITIES The Canon R3 can capture 6K video at up to 60fps in either Raw or more compressed formats.  The 6K capture uses the full sensor width which means no loss in field-of-view.  12-bit 6K capture is possible in both uncompressed Canon Raw or compressed Raw light formats.  10-bit H.265 is also possible in both the HDR PQ and Canon Log3 gamma curves to maximize dynamic range for post processing while maintaining smaller file sizes than a Raw format.  It's also possible (when using supported cards) to simultaneously record 10-bit 4:2:2 DCI 4K 60p video.  For those looking for higher frame rates, 10-bit 4:2:2 compressed 4K/120fps can also be captured, downsampled from the full sensor width.  A natively sampled 4K S35 crop is also an option, allowing for more magnification or the use of APS-C lenses.  The R3 also outputs a clean 6K signal over HDMI via an HDMI Micro Type D connector.  Direct custom white balance in live view is also now possible, making a critical function for underwater video even easier. STABILIZATION The R3 features 5-axis In Body Image Stabilization (IBIS) which can offer up to 8 stops of correction allowing for even smoother video and less camera movement related blur. LARGE ELECTRONIC VIEWFINDER The R3's EVF is an OLED 5.76M-dot that features an OVF simulation mode which leverages. the large dynamic range of the OLED screen to reproduce a scene the way it would look through an optical viewfinder.  The lower dynamic range of electronic viewfinders has always made them more difficult to use underwater, especially in high contrast or backlit scenes. This function can easily be switched on and off by assigning it to a custom function button.  When using the Electronic Shutter, which has an X-Sync speed of 1/180sec, the EVF delivers true no-blackout shooting up to 30fps.   Example setup THE NAUTICAM NA-R3 UNDERWATER HOUSING The Nauticam NA-R3 professional aluminum underwater housing for the Canon EOS R3 mirrorless full frame camera is a tru hybrid shooting solution, just as the R3 itself.  Nauticam has continuously supported both the Canon pro-level DSLR lineup as well as the growing full-frame RF-mount mirrorless cameras with innovative underwater housings and the new NA-R3 is the combination of all those technologies.  Blending elements of our 1D series housings with those for the R series, the NA-R3 will be the most capable housing for the R3 available. MISSION CONTROL Nauticam engineers design each housing to insure that controls are placed where they are needed most and within easy reach of a natural hand position.  The NA-R3 features large knurled control dials for the main and sub-command dials as well as an additional shoulder dial for the customizable control wheel of the R3.  A fourth control wheel, near the front of the left handle can articulate the ring of the optional EF-to-RF lens adapter when using EF lenses.  There is a dual thumb lever on the right side for Record and AF-ON as well as single levers for M-Fn and Fn2.  A lever on the left side actuates the Pv control which can change between exposure preview and OVF simulation modes on the EVF.  An additional dual thumb lever on the left side is for Playback and Magnification. HDMI 2.0 AND MOUNTING POINTS The R3 can output clean 6K 60p over HDMI and the NA-R3 features a large bore M24 bulkhead to support an HDMI 2.0 connection to an external monitor or recorder.  Mounting the monitor or recorder or other accessories is even easier with 3x 1/4"-20 mounting holes as well as an additional M10 mounting point atop the housing.  Check the resources sidebar for supported monitor/recorder housings and recommended accessories. FLASH TRIGGERING Flash triggering can be accomplished via the two included M14 electronic bulkheads (One is pre-installed in the M24 bulkhead via a removable M26-M14 adapter).  If using fiber-optic triggering, the built-in fiber optic bulkheads can be used with either the optional manual LED or TTL-flash triggers to provide the desired type of strobe power control. PREMIUM PROFESSIONAL OPTICS The NA-R3 is built around the N120 Canon RF-mount Port System which supports a wide array of Canon RF mount lenses with a selection of optical glass and acrylic ports.  With lens-removal controls for both EF and RF mount lenses, the NA-R3 can support both lens mount types without modification to the housing.  The EF-RF lens adapter is accommodated inside the housing which allows for the use of the N120 Canon EF-mount Port System without any additional extension rings.  When switching between an EF and RF lens, the camera must be removed to install or remove the adapter.  The Nauticam lineup of Premium Professional Optics can deliver unparalleled optical quality and expanded creative options. When used with the Canon RF 14-35 F/4 IL USM lens, the WACP-2 creates a stunning 140º field-of-view while maintaining an incredibly natural looking image and excellent corner sharpness.  The SMC-1 delivers 2.3x macro magnification to the RF 100mm macro lens while the SMC-2 delivers 3.3x. VACUUM CHECK AND LEAK DETECTION SYSTEM The housing comes with electronics pre-installed for Nauticam's Vacuum Check and Leak Detection system, requiring only the optional M16 Vacuum Valve (25625). This monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

With more cameras offering high quality HDMI video output, the Atomos Ninja V steps in, not only as a stunning monitor but also as a recorder of 4K 60p 4:2:2 10-bit video to on-board SSD drives in edit-friendly ProRes or Avid formats. The Nauticam NA-Ninja V, when used with supported housings and cameras, allows for the connection of the Ninja V over HDMI 2.0 in addition to providing easy access to the Ninja V controls underwater. Atomos Ninja V The Atomos Ninja V is an exceptional monitor, featuring a bright 1000 nit 10-bit HDR 5.2" screen that can display over 10 stops of dynamic range with compatible cameras. The monitor includes a variety of exposure and focus assist tools to insure your footage is properly exposed with critical focus. In addition to being an extremely capable monitor, the Ninja V is also a recorder. When used with compatible cameras over HDMI 2.0, the Ninja V can record 4K at 60p in 10-bit 4:2:2 ProRes or DNxHR formats to Atomos AtomX SSDmini solid state drives. With a 1TB SSDmini drive, the Ninja V can record up to 150 minutes of 4K video. EXPOSURE TOOLS  The Ninja V exposure guides include a Waveform for luminance, RGB Parade for color balance, and Vector Scope for hue and saturation. These tools, especially useful for the underwater filmmaker, allow accurate and fast judging of exposure, even in the most uncooperative lighting scenarios. Even when recording Log or HDR footage, using Rec.709 or HLG monitoring displays the video on the screen adjusted to the levels of the chosen standard.. FOCUS TOOLS Critical focus can be achieved using various peaking tools. Focus Peaking Color displays the original color image with the sharpest areas outlined in a selectable color. Focus Peaking Mono provides the same overlay but on a monochrome image. Focus Assist Outline shows only the false color outline on a black background of the sharpest Areas.   THE NAUTICAM NA-NINJA V UNDERWATER HOUSING The Nauticam NA-Ninja V builds on the strong foundation Nauticam has built with previous Atomos monitor/recorder housings but is built around the new M28 large-bore bulkhead that supports HDMI 2.0. The Ninja V is easily mounted in the housing, dropping in without trays or other mounting accessories and is held in place by two rotating locking levers. The Ninja V features both an HDMI 2.0 input as well as an output and the NA-Ninja V supports both as well. With dual M28 bulkheads, a second HDMI cable can be run to another monitor. The Ninja V allows for the application of. cube format 3D LUTs to this output signal. The NA-Ninja V supports up to the NP-F970 size battery which provides up to two hours of run time. A CR-2032 battery powers the vacuum check and leak detection system. When used with the included Vacuum Valve, the system gives real-time feedback about the watertight integrity of the housing through an easily visible multi-color LED on the top of the housing. Access to the touchscreen controls of the Ninja V are handled via a series of buttons and a selector knob beneath the screen of the housing including PLAY, REC, MON, RGB, PEAK and the Muti-Selector Lever.  

THE CANON EOS R5 CAMERA The Canon EOS R5 is the latest in Canon's full-frame mirrorless camera lineup which has gained unprecedented demand.  It features the RF lens mount which has the same large 54mm diameter but the ability to have larger rear lens elements that are closer to the sensor gives increased corner and outer edge sharpness.  The R5 uses an all new 45MP CMOS sensor with in-body image stabilization which can reduce shake by up to 8 stops.  The camera's Dual Pixel autofocus system uses 1053 autofocus points across the entire frame.   It is also capable of recording 8K video at 24p or 30p and 4K at up to 120p.   The EOS R5 can also use the large EF-mount lens lineup via three optional adapters, a simple EF to R adapter, one which supports the customizable control ring and another that features a drop-in filter mount. Key Camera Specifications 45MP full-frame Dual Pixel CMOS sensor 8K Video, with option for RAW or 10-bit 4:2:2 C-log or HDR PQ Up to 4K/120p, or oversampled 4K up to 30p 100% coverage Dual Pixel II AF system 12 fps / 20 fps burst (mechanical / electronic shutter) 5.76M-dot OLED EVF with 120fps max refresh rate 3.2" 2.1M-dot fully articulating touchscreen 10-bit HDR photos in HEIF format 1x CFExpress slot, 1x UHS-II SD slot Weather sealing   THE NAUTICAM NA-R5 UNDERWATER HOUSING FOR THE CANON EOS R CAMERA The NA-R5 underwater housing follows suit with Nauticam's drive for innovation. Both the Canon EOS R5 and EOS R present shooters with the ability to use both the available legacy EF lenses via an adapter in addition to their native RF optics.  To support both the legacy and native lenses, Nauticam has integrated the NA-R5 into the N120 port system. Canon's EF to RF mount adapters can be affixed to the camera before insertion into the housing. When using the EOS R5 inside the housing with the adapter and a supported EF lens, the port and extension ring arrangement will be identical to the same setup on a Nauticam Canon N120 DSLR. As the RF lens lineup emerges, dedicated port and extension ring combinations will be listed on the Port Chart. Two lens release buttons, one for RF and one for EF lenses used with the optional Canon adapter, are located on the front of the housing to make lens removal through the port opening simple. Mission Control Nauticam engineers are obsessed with getting the underwater image maker unfettered access to all the necessary controls, with as many within easy reach of the ergonomic rubberized handles. This Mission Control philosophy extends to the NA-R5 where a dual thumb lever and dual sub-lever are placed by the right handle. The upper thumb lever activates the "AF-On" and the lower the "Q" buttons while the sub-lever corresponds to the "M-Fn" and "Record" buttons. Near the left handle is a thumb lever for "Playback" as well as a dedicated switch to change from using LCD to the EVF. Large knurled and rubberized control dials access the camera's "main" and "sub" command dials. The two-stage trigger allows for smooth focus and firing activation. Additional buttons for "Menu", "Focus Point Selection" and others are also easily reached from the handles. An additional control wheel is located on the left side of the housing and will interface with the control ring on the supported EF to EOS R Mount Adapter with Control Ring using the optional gear (NA19561). Flash Triggering Flash triggering is achieved via one of two optional Flash Triggers, a manual LED trigger (NA26301) or a TTL Flash Trigger (NA26321) that use the built-in fiber optic bulkheads with optional fiber-optic cables to trigger supported strobes. For controlling strobes that do not support fiber optic flash triggering, a variety of legacy hot-shoe flash control bulkheads are available. Integrated vacuum check and leak detection system The Nauticam vacuum check and leak detection electronics are shipped with the NA-R5 as standard equipment. Combined with an accessory vacuum valve this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

This version is suitable to accommodate the Atomos AtomX SDI module. With more cameras offering high quality HDMI video output, the Atomos Ninja V steps in, not only as a stunning monitor but also as a recorder of 4K 60p 4:2:2 10-bit video to on-board SSD drives in edit-friendly ProRes or Avid formats. The Nauticam NA-Ninja V, when used with supported housings and cameras, allows for the connection of the Ninja V over HDMI 2.0 in addition to providing easy access to the Ninja V controls underwater.     Atomos Ninja V   The Atomos Ninja V is an exceptional monitor, featuring a bright 1000 nit 10-bit HDR 5.2" screen that can display over 10 stops of dynamic range with compatible cameras. The monitor includes a variety of exposure and focus assist tools to insure your footage is properly exposed with critical focus. In addition to being an extremely capable monitor, the Ninja V is also a recorder. When used with compatible cameras over HDMI 2.0, the Ninja V can record 4K at 60p in 10-bit 4:2:2 ProRes or DNxHR formats to Atomos AtomX SSDmini solid state drives. With a 1TB SSDmini drive, the Ninja V can record up to 150 minutes of 4K video. EXPOSURE TOOLS  The Ninja V exposure guides include a Waveform for luminance, RGB Parade for color balance, and Vector Scope for hue and saturation. These tools, especially useful for the underwater filmmaker, allow accurate and fast judging of exposure, even in the most uncooperative lighting scenarios. Even when recording Log or HDR footage, using Rec.709 or HLG monitoring displays the video on the screen adjusted to the levels of the chosen standard.. FOCUS TOOLS Critical focus can be achieved using various peaking tools. Focus Peaking Color displays the original color image with the sharpest areas outlined in a selectable color. Focus Peaking Mono provides the same overlay but on a monochrome image. Focus Assist Outline shows only the false color outline on a black background of the sharpest areas.    THE NAUTICAM NA-NINJA V UNDERWATER HOUSING   The Nauticam NA-Ninja V builds on the strong foundation Nauticam has built with previous Atomos monitor/recorder housings but is built around the new M28 large-bore bulkhead that supports HDMI 2.0. The Ninja V is easily mounted in the housing, dropping in without trays or other mounting accessories and is held in place by two rotating locking levers. The Ninja V features both an HDMI 2.0 input as well as an output and the NA-Ninja V supports both as well. With dual M28 bulkheads, a second HDMI cable can be run to another monitor. The Ninja V allows for the application of. cube format 3D LUTs to this output signal. The NA-Ninja V supports up to the NP-F970 size battery which provides up to two hours of run time. A CR-2032 battery powers the vacuum check and leak detection system. When used with the included Vacuum Valve, the system gives real-time feedback about the watertight integrity of the housing through an easily visible multi-color LED on the top of the housing. Access to the touchscreen controls of the Ninja V are handled via a series of buttons and a selector knob beneath the screen of the housing including PLAY, REC, MON, RGB, PEAK and the Muti-Selector Lever.  

The Canon EOS R5 is attractive to underwater image makers for a variety of reasons. It is a 45MP full frame mirrorless camera that shoots full width 8K video, utilizes Canon's new RF lens mount, and also has next generation Dual Pixel autofocus. The Canon EOS R6 Camera The Canon EOS R6 is one of the latest in Canon's full-frame mirrorless camera lineup which has gained unprecedented demand.  It features the RF lens mount which has the same large 54mm diameter but the ability to have larger rear lens elements that are closer to the sensor gives increased corner and outer edge sharpness.  The R6 uses an 20MP CMOS sensor which is closely related to the one used in the Canon 1D X Mark III flagship camera.  It offers in-body image stabilization rated at up to 8 stops of correction.  The camera's Dual Pixel autofocus system uses 1053 autofocus points across the entire frame.   It is also capable of recording 4K video at up to 60p and 1080 at up to 120p.   The EOS R6 can also use the large EF-mount lens lineup via three optional adapters, a simple EF to R adapter, one which supports the customizable control ring and another that features a drop-in filter mount. Key Camera Specifications 20MP full-frame Dual Pixel CMOS sensor UHD 4K shooting up to 60p, 1080 at up to 120p, 10-bit 4:2:2 internal recording in C-Log or HDR PQ 100% coverage Dual Pixel II AF system 12 fps / 20 fps burst (mechanical / electronic shutter) 3.68M-dot EVF 1.62M-dot fully-articulated rear touchscreen 10-bit HDR photos in HEIF format Dual UHS-II SD slots The Nauticam Underwater Housing for the Canon EOS R6 Camera The NA-R6 underwater housing follows suit with Nauticam's drive for innovation. Both the Canon EOS R5 and EOS R6 present shooters with the ability to use both the available legacy EF lenses via an adapter in addition to their native RF optics.  To support both the legacy and native lenses, Nauticam has integrated the NA-R6 into the N120 port system. Canon's EF to RF mount adapters can be affixed to the camera before insertion into the housing. When using the EOS R6 inside the housing with the adapter and a supported EF lens, the port and extension ring arrangement will be identical to the same setup on a Nauticam Canon N120 DSLR. As the RF lens lineup emerges, dedicated port and extension ring combinations will be listed on the Port Chart. Two lens release buttons, one for RF and one for EF lenses used with the optional Canon adapter, are located on the front of the housing to make lens removal through the port opening simple. Mission Control Nauticam engineers are obsessed with getting the underwater image maker unfettered access to all the necessary controls, with as many within easy reach of the ergonomic rubberized handles. This Mission Control philosophy extends to the NA-R6 where a dual thumb lever and dual sub-lever are placed by the right handle. The upper thumb lever activates the "AF-On" and the lower the "Q" buttons while the sub-lever corresponds to the "M-Fn" and "Record" buttons. Near the left handle is a thumb lever for "Playback" as well as a dedicated switch to change from using LCD to the EVF. Large knurled and rubberized control dials access the camera's "main" and "sub" command dials. The two-stage trigger allows for smooth focus and firing activation. Additional buttons for "Menu", "Focus Point Selection" and others are also easily reached from the handles. An additional control wheel is located on the left side of the housing and will interface with the control ring on the supported EF to EOS R Mount Adapter with Control Ring using the optional gear (NA19561). Flash Triggering Flash triggering is achieved via one of two optional Flash Triggers, a manual LED trigger (NA26301) or a TTL Flash Trigger (NA26321) that use the built-in fiber optic bulkheads with optional fiber-optic cables to trigger supported strobes. For controlling strobes that do not support fiber optic flash triggering, a variety of legacy hot-shoe flash control bulkheads are available. Integrated Vacuum Check and Leak Detection System The Nauticam vacuum check and leak detection electronics are shipped with the NA-R6 as standard equipment. Combined with an accessory vacuum valve (NA25625) this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

This housing is fully compatible with the OM System OM-1 Mark II Camera. The OM Systems OM-1, the first high-end Micro Four Thirds mirrorless camera from OM Digital Solutions. The OM-1 features a 20MP quad-pixel AF stacked CMOS sensor.  It is paired with the latest TruePic X processor to deliver 3x faster processing speeds and is capable of 120 fps shooting with the electronic shutter. The O-M1 can also capture 4K UHD or DCI at 60p in the OM-Log profile for great color grading range. The OM-1 camera by Olympus OM Systems has announced the OM-1. The new camera is supposed to top all previous models and have the absolute "WOW factor". Autofocus, image stabiliser and processor are said to be convincingly better. It will be available from the beginning of March. The OM-1 is to be the new MFT flagship from Olymus. With its 20MP sensor, it is said to be capable of 120 frames/s at full resolution. It also has an extremely fast image sensor. OM System promises that subject tracking and autofocus tracking will be faster and better than ever before. But there's also been a big upgrade in the image stabiliser. Key Camera Specs 20MP Stacked CMOS Sensor 1053 X-type AF points Up to 120 fps with electronic shutter Image stabilization rated to 7EV of correction (up to 8EV with compatible lenses) Large 5.76M-dot OLED electronic viewfinder Dual UHS-II SD card slots UHD or DCI 4K/60p video, 1080 up to 240 fps Weather sealing rated to IP53 Olympus OM-1 underwater housing by Nauticam The OM Systems OM-1 is characterized by its combination of extreme customizability and impressive stabilization in a compact hybrid-shooting package. The Nauticam NA-OM1, similar to the OM-1 is a refinement of it's predecessors. Nauticam has produced housings for wide range of Micro Four Thirds cameras from Olympus and Panasonic. Throughout the evolution of Micro Four Thirds cameras, Nauticam has adapted our design to help image makers get take full advantage of every camera advancement. More than a simple waterproof case, the NA-OM1 integrates with the OM-1 to adapt and improve upon the camera's features for underwater shooting. MISSION CONTROL Regardless of where a dial or button may be found on the camera body, Nauticam engineers make sure it is located where it is needed most on the housing. This Mission Control philosophy drives the design of every housing and provides for the most intuitive and easy to use housings available. The NA-OM1 features a thumb lever, easily accessed from the ergonomic rubberized right handle that actuates the AF-ON control.  This back-button autofocus method prevents the camera from refocusing between shots, allowing the user fine control over a shot's focus and is critical whether shooting macro or fast moving wide-angle subjects. FLASH TRIGGERING The OM-1 can be used with the optional Olympus FL-LM3 flash inside the NA-OM1 underwater housing by Nauticam to provide accurate TTL flash triggering through the integrated Sea&Sea style fiber optic bulkheads. For high-speed manual flash triggering, the optional Mini Flash Trigger for Olympus (26306) can be used. The trigger is powered by onboard coin style lithium batteries, with thousands of flashes available from a set. Electrical triggering of legacy wired strobe systems is possible via an electrical Nikonos style bulkhead (optional). PREIUM PROFESSIONAL OPTICS A camera system is only as good as the optics placed in front of it. Nauticam's extensive line of dome and flat ports support a wide variety of Micro Four Thirds lenses. For even higher image quality and versatility, the NA-OM1 can be used in conjunction with Nauticam's lineup of Water Contact Optics. For example, with the Olympus 14-42mm f/3.5-5.6 EZ Lens, the Nauticam WWL-1 provides a full zoom through ultra wide-angle 130º field of view. MAGNIFYING VIEWFINDERS A clear view for fine focus and composition is critical for successful underwater photography, and nothing beats a magnifying viewfinder. These viewfinders use distance, not closeup vision, and provide a large, clear view of the high resolution Olympus electronic viewfinder. Available in Angled 45º (PN 32205 or 32213) and Straight 180º (PN 32204 or 32211) formats, both viewfinders have external dioptric adjustments for dialing in perfect correction matched to the photographer’s eyesight.  The Full Frame Angle Viewfinder 32°/ 1:1 (32213) or the Full Frame Straight Viewfinder 32°/ 1:1 (32211) requires the 32215 Viewfinder Collar Adaptor. INTEGRATED VACUUM CHECK AND LEAK DETECTION SYSTEM The Nauticam Vacuum check and leak detection system is available with NA-OM1 Underwater Housing as standard equipment. Combined with an optional vacuum valve (PN 25624), this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur.

The latest Canon APS-C mirrorless camera is finally here!  The Canon EOS R7 utilizes Canon's newest RF mount and boasts a 32.5MP CMOS sensor.  Crop-sensor cameras have always been popular with the underwater shooter community and with good reason. Lens choices, size, and weight are just a few of the great features that shooting APS-C cameras has. The EOS R7 gives original Canon 7D and 7D Mark II shooters a great reason to upgrade and Nauticam is ready to help with the NA-R7 housing.   The Canon EOS R7 Camera The Canon EOS R7 is the latest in Canon's APS-C mirrorless camera lineup which has gained unprecedented demand.  It features the RF lens mount which has the same large 54mm diameter but the ability to have larger rear lens elements that are closer to the sensor gives increased corner and outer edge sharpness.  The R7 uses a 32.5MP CMOS sensor with in-body image stabilization which can reduce shake by up to 7 stops.  The camera's Dual Pixel II autofocus system was carried over from the pro body EOS R3 and features 651 automatic AF points covering the entire sensor area.  It is also capable of recording oversampled 4K 30p video using the full 7K area of the sensor, or subsampled UHD 4K up to 60p from the full sensor width.   The Canon EOS R7 can also use the large EF-mount lens lineup via a simple EF to EOS R adaptor.  The Nauticam NA-R7 housing only supports the the standard EF to EOS R adaptor and does give access to the control ring or drop in filter adaptors.   Key features - Canon EOS R7 32.5MP APS-C CMOS sensor with Dual Pixel AF Up to 30 fps shooting (e-shutter), 15 fps with mechanical In-body image stabilization, rated at up to 7 stops Oversampled UHD 4K up to 30p, line-skipped or cropped 4K/60p 10-bit video as 'PQ' true HDR footage or C-Log 2.36M dot OLED viewfinder 1.62M dot fully-articulating touchscreen Twin UHS-II SD card slot Environmental sealing The Canon EOS R7 underwater housing from Nauticam   The NA-R7 underwater housing follows suit with Nauticam's drive for innovation. Like the full frame Canon EOS R5, R5 C and R3, the NA-R7 present shooters with the ability to use both the available legacy EF lenses via an adapter in addition to their native RF optics.  To support both the legacy and native lenses, Nauticam has designed a N100 to N120 adapter which integrates into the N120 Canon EF port system. Canon's EF to RF mount adapters can be affixed to the camera before insertion into the housing. When using the EOS R7 inside the housing with the adapter and a supported EF lens, the port and extension ring arrangement will be identical to the same setup on a Nauticam Canon N120 DSLR. As the RF-S lens lineup emerges, dedicated port and extension ring combinations will be listed on the new N100 RF-S Port Chart.  Mission Control Nauticam engineers are obsessed with getting the underwater image maker unfettered access to all the necessary controls, with as many within easy reach of the ergonomic rubberized handles. This Mission Control philosophy extends to the NA-R7 where a dual thumb lever is placed by the right front side accessing the M-Fn and Record buttons.  On the rear right side is a thumb lever accessing AF-ON. Near the left handle is a thumb lever for "Playback." Large knurled and rubberized control dials access the camera's "main" and "sub" command dials. The two-stage trigger allows for smooth focus and firing activation. Additional buttons for "Menu", "Focus Point Selection" and others are also easily reached from the handles. Flash triggering Flash triggering is achieved via one of two optional Flash Triggers, a manual LED trigger (NA26305) or a TTL Flash Trigger (NA26321) that use the built-in fiber optic bulkheads with optional fiber-optic cables to trigger supported strobes. For controlling strobes that do not support fiber optic flash triggering, a variety of legacy hot-shoe flash control bulkheads are available. Integrated system for vacuum testing and leak detection The Nauticam vacuum check and leak detection electronics are shipped with the NA-R7 as standard equipment. Combined with an accessory vacuum valve (NA25624) this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

The Canon EOS R6 Mark II may look like it's predecessor, but it offers a lot of new features attractive to underwater image makers. It has a new 24MP full frame sensor, it is capable of recording UHD 4K/60p without any crop factor internally and also supports ProRes RAW recording up to 6K to an external recorder such as the Ninja V. The Canon EOS R6 II Camera The Canon EOS R6 Mark II is one of the latest in Canon's full-frame mirrorless camera lineup which has gained unprecedented demand.  It features the RF lens mount which has the same large 54mm diameter but the ability to have larger rear lens elements that are closer to the sensor gives increased corner and outer edge sharpness.  TThe R6 Mark II uses an all new 24MP CMOS sensor which boosts the resolution from its predecessor and also significantly improves its rolling shutter performance. It offers in-body image stabilization rated at up to 8 stops of correction. The camera's Dual Pixel CMOS AF II autofocus system uses 1053 autofocus points across the entire frame. It is also capable of recording 4K video at up to 60p internally and 6K 60p extern The EOS R6 Mark II can also use the large EF-mount lens lineup via the Canon RF to EOS R Adapter. Key specifications 24.2MP full-frame CMOS sensor UHD 4K shooting up to 60p, 1080 at up to 120p, 6K ProRes RAW recording externally up to 60p 100% coverage Dual Pixel II AF system 12 fps / 40 fps burst (mechanical / electronic shutter) 3.69M-dot OLED EVF 3" 1.62M-dot vari-angle touchscreen LCD 580 shot-per-charge battery rating Dual UHS-II SD Slots The Nauticam Underwater Housing for the Canon EOS R6 Mark II Camera The NA-R6II underwater housing follows suit with Nauticam's drive for innovation and it supports both the Canon EOS R6 and R6 Mark II. A conversion kit is required for the original R6 and will be provided upon request. Like its predecessors, the NA-R6II presents shooters with the ability to use both the available legacy EF lenses via an adapter in addition to their native RF optics. To support both the legacy and native lenses, Nauticam has integrated the NA-R6II into the N120 port system. Canon's EF to RF mount adapters can be affixed to the camera before insertion into the housing. When using the EOS R6 Mark II inside the housing with the adapter and a supported EF lens, the port and extension ring arrangement will be identical to the same setup on a Nauticam Canon N120 DSLR. With the ever growing RF lens lineup, you can also follow the dedicated N120 Canon RF port chart that is being updated and expanded with each new lens release. Please note that the Canon Control Ring and Drop-in Filter EF to EOS R adapters are not accessible within the housing. Mission Control Nauticam engineers are obsessed with getting the underwater image maker unfettered access to all the necessary controls, with as many within easy reach of the ergonomic rubberized handles. This Mission Control philosophy extends to the NA-R6II where a dual thumb lever and sub-lever are placed by the right handle. The dual thumb lever on the front right side activates the "M-Fn" and "Rec" buttons while the sub-lever on the right rear side corresponds to the "AF-ON" button. Near the left handle is a thumb lever for "Playback" for easy image review. Large knurled and rubberized control dials access the camera's "main" and "sub" command dials. The two-stage trigger allows for smooth focus and firing activation. Additional buttons for "Menu", "Focus Point Selection" and others are also easily reached from the handles Flash Triggering Flash triggering is achieved via one of two optional Flash Triggers, a manual LED trigger (NA26301) or a TTL Flash Trigger (NA26321) that use the built-in fiber optic bulkheads with optional fiber-optic cables to trigger supported strobes. For controlling strobes that do not support fiber optic flash triggering, a variety of legacy hot-shoe flash control bulkheads are available. Integrated Vacuum Check and Leak Detection System The Nauticam vacuum check and leak detection electronics are shipped with the NA-R6 as standard equipment. Combined with an accessory vacuum valve (NA25625) this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.