Canon EOS R5 Underwater Housing by Nauticam
Photos show accessories that are not part of your order. Only the content of the tab "What's in the box" is relevant.
Product number:
NA17333
HAN:
NA-R5
THE CANON EOS R5 CAMERA
The Canon EOS R5 is the latest in Canon's full-frame mirrorless camera lineup which has gained unprecedented demand. It features the RF lens mount which has the same large 54mm diameter but the ability to have larger rear lens elements that are closer to the sensor gives increased corner and outer edge sharpness.
The R5 uses an all new 45MP CMOS sensor with in-body image stabilization which can reduce shake by up to 8 stops. The camera's Dual Pixel autofocus system uses 1053 autofocus points across the entire frame. It is also capable of recording 8K video at 24p or 30p and 4K at up to 120p.
The EOS R5 can also use the large EF-mount lens lineup via three optional adapters, a simple EF to R adapter, one which supports the customizable control ring and another that features a drop-in filter mount.
Key Camera Specifications
- 45MP full-frame Dual Pixel CMOS sensor
- 8K Video, with option for RAW or 10-bit 4:2:2 C-log or HDR PQ
- Up to 4K/120p, or oversampled 4K up to 30p
- 100% coverage Dual Pixel II AF system
- 12 fps / 20 fps burst (mechanical / electronic shutter)
- 5.76M-dot OLED EVF with 120fps max refresh rate
- 3.2" 2.1M-dot fully articulating touchscreen
- 10-bit HDR photos in HEIF format
- 1x CFExpress slot, 1x UHS-II SD slot
- Weather sealing
THE NAUTICAM NA-R5 UNDERWATER HOUSING FOR THE CANON EOS R CAMERA
The NA-R5 underwater housing follows suit with Nauticam's drive for innovation. Both the Canon EOS R5 and EOS R present shooters with the ability to use both the available legacy EF lenses via an adapter in addition to their native RF optics. To support both the legacy and native lenses, Nauticam has integrated the NA-R5 into the N120 port system. Canon's EF to RF mount adapters can be affixed to the camera before insertion into the housing. When using the EOS R5 inside the housing with the adapter and a supported EF lens, the port and extension ring arrangement will be identical to the same setup on a Nauticam Canon N120 DSLR. As the RF lens lineup emerges, dedicated port and extension ring combinations will be listed on the Port Chart. Two lens release buttons, one for RF and one for EF lenses used with the optional Canon adapter, are located on the front of the housing to make lens removal through the port opening simple.
Mission Control
Nauticam engineers are obsessed with getting the underwater image maker unfettered access to all the necessary controls, with as many within easy reach of the ergonomic rubberized handles. This Mission Control philosophy extends to the NA-R5 where a dual thumb lever and dual sub-lever are placed by the right handle. The upper thumb lever activates the "AF-On" and the lower the "Q" buttons while the sub-lever corresponds to the "M-Fn" and "Record" buttons. Near the left handle is a thumb lever for "Playback" as well as a dedicated switch to change from using LCD to the EVF.
Large knurled and rubberized control dials access the camera's "main" and "sub" command dials. The two-stage trigger allows for smooth focus and firing activation. Additional buttons for "Menu", "Focus Point Selection" and others are also easily reached from the handles.
An additional control wheel is located on the left side of the housing and will interface with the control ring on the supported EF to EOS R Mount Adapter with Control Ring using the optional gear (NA19561).
Flash Triggering
Flash triggering is achieved via one of two optional Flash Triggers, a manual LED trigger (NA26301) or a TTL Flash Trigger (NA26321) that use the built-in fiber optic bulkheads with optional fiber-optic cables to trigger supported strobes. For controlling strobes that do not support fiber optic flash triggering, a variety of legacy hot-shoe flash control bulkheads are available.
Integrated vacuum check and leak detection system
The Nauticam vacuum check and leak detection electronics are shipped with the NA-R5 as standard equipment. Combined with an accessory vacuum valve this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur.
The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.
| Arm Attachment: | 1-inch ballhead |
|---|---|
| Body Material: | aluminum |
| Camera System: | Mirrorless (MIL) |
| Camera manufacturer: | CANON |
| Strobe connector: | optical Sea&Sea |
| Tripod connection: | Thread ¼ |
| portsystem: | N120 |
Technical data
- Dimensions: 357mm x 200mm x 161mm (W x H x D)
- Depth Rating: 100m
- Weight in air: 3.5kg
- Weight in water: -0.05kg (includes camera and battery)
- Port Opening: N120
Scope of delivery
- Canon EOS R5 Underwater Housing by Nauticam
- Spare main o-ring, lubricant and removal tool
- 2x Optical bulkhead caps
- 2x Handles with mounting balls
- Set of allen keys
- CR2032 battery for leak detector
- Padded housing bag and shoulder strap
Only the components of the item that are listed here will be delivered. Accessories and/or decoration shown in our images are for demonstration purposes only. In particular, we would like to point out that the purchase of an underwater housing does not include a camera and often not a port nor an external viewfinder. If you have any questions about the configuration of your system, do not hesitate to contact us.
Login
There aren't any asked questions yet.
Flash Trigger
on stock
e-TURTLE MANUAL trigger for Canon systems
€295.00*
A reliable Manual trigger for underwater photographers that works via fiber optic cable or sync cord.
e-TURTLE MANUAL
This Manual trigger was developed for Canon DSLR and MILC camera systems. The e-TURTLE MANUAL is the perfect choice for the demanding underwater photographer who needs an easy to use, affordable, and reliable trigger that works with the most popular underwater strobes (Inon, Ikelite, Sea&Sea, Subtronic, OneUW, Retra, Backscatter miniflash etc).
Features: 1st or 2nd curtain, HSS mode (Over 1/200 shutter speed the TURTLE enable the HSS and disable the 2nd curtain mode).
The Internal charging system works via a USB AB connector.
Compatible camera models are the Canon DSLR and Mirrorless cameras.
Compatible strobes (as of 01.09.2020.): Ikelite DS160, Inon Z240/Z330, Sea&Sea YS-250, YS-D1, YS-D2, D2J YS-D3, YS-110a, Subtronic Pro 160, Pro 270, One UW, Retra (old and new models), Retra PRO (HSS mode available!)
The e-TURTLE MANUAL is a user-friendly trigger: you simply connect the LED or the sync cord connector and you can take hundreds of shots without charging. The TURTLE MANUAL triggers fit into the most popular underwater housings (tested with Nauticam, Subal, Hugyfot, Isotta, Ikelite, Seacam models).
If you want to connect your strobe via fiber optic cable we recommend using multicore cable! (Please write Us which kind of connection do you use. We also recommend writing us what kind of underwater strobe will you control with the TURTLE trigger so we can be sure you got a product which fulfills your needs.) There is also a USB cable in the package for charging.
on stock
TTL Converter for Canon in Naurticam and Hugyfot housings
€499.00*
Optoelectronic flash trigger for Canon cameras in Nauticam and Hugyfot housings.
The world's first TTL converter that is compatible with all Canon DSLR and DSLM cameras, regardless of model or TTL protocol version.
Compatible underwater flashes: Inon Z330, Z240; Ikelite DS-161, DS-160; Sea&Sea YS-D1, YS-D2 (made-in-China), YS-250, RetraFlash PRO and Prime (including HSS support).
The product supports 4 pcs TTL outputs: 2 pcs optical bulkheads + 2 pcs electrical bulkheads can be connected. TTL converter has automatic on/off, incredible battery life 5 years. Easy installation by the user.
TTL and HSS on RetraFlash
Fantastic TTL accuracy allows photographers to relax and rely completely on automatic flash exposure control. Many creative tasks are made possible by using extremely fast HSS shutter speeds of up to 1/8000 with the Retra Pro flash in manual mode. The TTL converter firmware also has some other important updates related to its common functionality.
The Retra PRO profile can be set by the user üvia the TTL converter's built-in rotary switch.
The TTL/M modes can be switched underwater simply by using the camera name or the flash button.
In manual mode, the flash intensity can be adjusted manually üvia the camera wheel/scale, but also üvia the flash control knob.
(+/-) TTL flash compensation is supported by the firmware, the full range is available via the camera control in the range -3ev......+3ev.
The firmware supports sync settings for the 1-st /2-nd curtain and the rear curtain.
Continuous (serial) recording is supported.
The HSS firmware of the TTL converter supports the HSS functionality of the Retra Pro flash. The built-in rotary switch must be set to the Retra Pro profile (position - "7"). Available HSS shutter speeds for Sony A7-A9: 1/320 ....1/8000 sec. The Retra flash allows the HSS flash intensity to be set using the rotary knob.
In the updated firmware, switching to HSS shutter speeds is also included in the general functionality of the TTL converter (also for all other positions of the rotary switch), - usable for shooting with ambient light at high shutter speeds if required. However, the X-Sync speed limit (1/250 for Sony A7-A9) is still automatically supported for TTL modes, as required for mono flash TTL underwater flash.
Incredibly long battery life in the TTL converter: 1-3 years of continuous operation. The product has extremely low power consumption.
The converter features an automatic on/off switching module that saves battery power. No mechanical switch is required to switch UW Technics TTL converters on and off.
The TTL converter firmware includes TTL profiles for the following underwater flashes: Retra Pro, Inon Z-330/ Z-240/S-2000, Sea&Sea YS-D2/ YS-D1/ YS-250, Ikelite DS-161/ DS-160 and Subtronic Pro-270/Pro-160. Each profile can be easily set by the user üvia an onboard switch.
Similar products
Canon EOS R5C Underwater Housing by Nauticam
€6,240.00*
THE CANON EOS R5C CAMERA
The Canon EOS R5C is the latest in Canon's full-frame mirrorless camera lineup which has gained unprecedented demand. It features the RF lens mount which has the same large 54mm diameter but the ability to have larger rear lens elements that are closer to the sensor gives increased corner and outer edge sharpness.
The R5C uses an all new 45MP CMOS sensor with in-body image stabilization which can reduce shake by up to 8 stops. The camera's Dual Pixel autofocus system uses 1053 autofocus points across the entire frame. It is also capable of recording 8K video at 24p or 30p and 4K at up to 120p.
The EOS R5C can also use the large EF-mount lens lineup via three optional adapters, a simple EF to R adapter, one which supports the customizable control ring and another that features a drop-in filter mount.
Key Camera Specifications
45MP full-frame Dual Pixel CMOS sensor
8K Video, with option for RAW or 10-bit 4:2:2 C-log or HDR PQ
Up to 4K/120p, or oversampled 4K up to 30p
100% coverage Dual Pixel II AF system
12 fps / 20 fps burst (mechanical / electronic shutter)
5.76M-dot OLED EVF with 120fps max refresh rate
3.2" 2.1M-dot fully articulating touchscreen
10-bit HDR photos in HEIF format
1x CFExpress slot, 1x UHS-II SD slot
Weather sealing
THE NAUTICAM NA-R5C UNDERWATER HOUSING FOR THE CANON EOS R5C CAMERA
The NA-R5C underwater housing follows suit with Nauticam's drive for innovation. Both the Canon EOS R5C and EOS R present shooters with the ability to use both the available legacy EF lenses via an adapter in addition to their native RF optics. To support both the legacy and native lenses, Nauticam has integrated the NA-R5 into the N120 port system. Canon's EF to RF mount adapters can be affixed to the camera before insertion into the housing. When using the EOS RC5 inside the housing with the adapter and a supported EF lens, the port and extension ring arrangement will be identical to the same setup on a Nauticam Canon N120 DSLR. As the RF lens lineup emerges, dedicated port and extension ring combinations will be listed on the Port Chart. Two lens release buttons, one for RF and one for EF lenses used with the optional Canon adapter, are located on the front of the housing to make lens removal through the port opening simple.
Mission Control
Nauticam engineers are obsessed with getting the underwater image maker unfettered access to all the necessary controls, with as many within easy reach of the ergonomic rubberized handles. This Mission Control philosophy extends to the NA-R5C where a dual thumb lever and dual sub-lever are placed by the right handle. The upper thumb lever activates the "AF-On" and the lower the "Q" buttons while the sub-lever corresponds to the "M-Fn" and "Record" buttons. Near the left handle is a thumb lever for "Playback" as well as a dedicated switch to change from using LCD to the EVF.
Large knurled and rubberized control dials access the camera's "main" and "sub" command dials. The two-stage trigger allows for smooth focus and firing activation. Additional buttons for "Menu", "Focus Point Selection" and others are also easily reached from the handles.
An additional control wheel is located on the left side of the housing and will interface with the control ring on the supported EF to EOS R Mount Adapter with Control Ring using the optional gear (NA19561).
Flash Triggering
Flash triggering is achieved via one of two optional Flash Triggers, a manual LED trigger (NA26301) or a TTL Flash Trigger (NA26321) that use the built-in fiber optic bulkheads with optional fiber-optic cables to trigger supported strobes. For controlling strobes that do not support fiber optic flash triggering, a variety of legacy hot-shoe flash control bulkheads are available.
INTEGRATED VACUUM CHECK AND LEAK DETECTION SYSTEM
The Nauticam vacuum check and leak detection electronics are shipped with the NA-R5C as standard equipment. Combined with an accessory vacuum valve this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur.
The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.
Canon EOS R5 Underwater Housing by Sea&Sea
€4,195.00*
MDX-R5
U/W HOUSING FOR CANON EOS R5
Revised ergonomic design, improved safety features and eye-catching exterior. The new MDX series housings are now upgraded with more standard features to ensure better handling and greater protection for your camera
Features
Equipped with Grip plus,SA8 Fixed Ball Bases
The new MDX R5 is the perfect complement to Canon`s new mirrorless R5 camera. The MDX-R5 is rich in features with all controls ergonomically designed to maximize camera operation. All major camera functions can be accessed from the grip handles through thumb or finger movement without releasing your grip.
Sea&Sea Optical Converter and S&S manual flash trigger compatibility, port locking system plus removal and attaching of lenses while camera is still in housing. Compatible with both native RF lenses and all EF lenses (with mount). In addition, a 24mm port has been included to accommodate HDMI 2 cables for connection to an external video monitor to realize the full potential of the cameras ultra-high video capabilities. A built-in Leak Sensor and a bulkhead for external vacuum sensor provides double protection and increased peace of mind for your camera equipment while diving.
Many more features are available on the MDX R5 to help you gain full potential of all the R5`s features and make your underwater imaging experience unforgettable.
MDX-R5 with YS-D3 Strobes
For better noticeability, controls are partially colored with yellow.
All major controls for camera function can be easily operated without releasing your grip on the handle, providing stability and assurance during all imaging situations
Compatible with the Sea&Sea, “Manual Flash Trigger” (optional). and Sea&Sea Optical TTL Coverter.
24mm bulkhead allows connection of 3rd party HDMI 2 cable for attaching an external video monitor
Bulkhead will accept the S&S Vivid housing Vacuum Leak Sensor, or an optional 16mm step down converter is available to fit third party vacuum sensors
Compatible with all the DX (NX) series ports.
The camera can be removed from the housing easily even if a lens with large diameter such as the RF15~35 f2.8 is mounted on the camera without removing port from the housing enabling you to replace battery and lens with ease.
MDX-R5 Other Features
The Port lock prevents the port from turning or loosening and the Port Lock lever is specifically located to avoid being unlocked accidentally.
The housing is equipped with a lens-lock release button which makes it possible to change lenses easily, without opening the housing.
Pulling out the Focus/Zoom Dial gives sufficient room inside the housing to easily accommodate larger diameter lenses.
All controls have luminescense stickers which glow in a dark enbironment for better visibility of controls.
Equipped with Optical Viewfinder 0.5x as standard. Other optional viewfinders such as the VF180 1.2x,VF45 1.2x and Optical Viewfinder 0.66x,0.8x can be used.?Some vignetting may occur when the VF180 1.2x is mounted on housing, the upper part of the camera's viewfinder cannot be viewed dus to vignetting.
Sync Cord 2-pin Connector enables use of conventional hardwired Sync cable (Manual mode only).
Equipped with two sacrificial zinc diodes (one on the fornt case and the other on the rear) to prevent electrolysis damege.
Built-in leak sensor immediately alerts alerts you to water ingress.Tripod screw mount is located on the center underside of the housing.
Equipped with an under guard to protect housing from scratches and abrasion
Canon EOS R5 Underwater Housing by Isotta
€3,390.00*
The new Canon EOS R5 promises a revolution in photography and cinema. By employing new technologies, including artificial intelligence for AF and an image stabilizer that comes with up to 8 stops* of protection against vibration, Canon aims to make users forget what they knew about Mirrorless cameras. 45-megapixel photos at 20 frames per second, 4K/120P full frame video and a choice of ISO 100-51200. This camera promises outstanding photos in any conditions. With the built-in, always-on Bluetooth Low Energy connection, establishing a fast Wi-Fi connection with a smart device and reviewing your shots already on the way back is a snap.
* 8 stops based on standard CIPA tests with RF 24-105mm F4 L IS USM at a focal length of 105mm.
Product details Canon EOS R5 Underwater Housing by Isotta
The housing respects all the key points of Isotta's line of housings: one-handed opening, double O-ring seals for greater safety, the use of high quality materials and the made in Italy craftsmanship. The housing was created to follow the lines of the camera, resulting small and manageable, while ensuring complete control of camera functions and absolute freedom in the use of accessories.
MAN BEFORE MACHINE!
The focus in the study of the housing goes to the diver who decides to use it. The comfort in the use and management of the machine in water is a fixed point, studied in every detail. The handles are ergonomic, adjustable and interchangeable*. if necessary; the housing is compact and lightweight, so you won't tire your arm too much and have an excellent control over stability. All buttons are conveniently reachable from the grip position of the handles ensuring maximum management of the camera with minimum effort. The rear back offers a full view of the camera screen so that you can shoot in live view unobstructed and in comfort and it detaches completely from the front body so that it is easy to insert the camera and perform operations inside the housing. The presence of the viewfinder allows you to take pictures framing in the classic way and to replace it with a magnifier. The closing knob is Single-hand actionable.
MORE AND MORE CUSTOMIZABLE!
Supplied with only the connections for the optical fiber, the housing has been designed with three M16x1 connections and one M24x1 connection, for total freedom in the choice of the conformation of the equipment. When ordering, you can select your preferred lighting control system choosing between Trigger, Sincro N5 or S6 and your right port system. Through the different combinations between ports and extension rings it is possible to use most of the lenses on the market.
Various accessories can be used by means of an M8 hole located at the top of the case and two M6 threaded holes located at the bottom. To make it even more unique, have your name or logo engraved.
SAFETY IS IMPORTANT!
The locking pins on the back are made of stainless steel and penetrate the shell for added strength and security. The housing is made of aluminum, resistant and anti-corrosion, anodized in the unmistakable red color. The classic double o-ring seal is on all moving and removable parts ensures an optimal watertight seal. The camera is held straight, centered and in place by a mounting plate with a safety catch, which slips nimbly into the housing. NNo risk of sudden infiltration. A red humidity alarm inside the case is powered by a user-replaceable battery and instantly signals an increase in humidity in a critical area. Watertightness is guaranteed up to a maximum depth of 100 meters.
Highlights
Ergonomic side handles, adjustable (via optional accessory)
Two built-in fiber optic connectors
Two standard electrical sync cord bulkheads Nikonos N5 or S6 not included
Back housing completely detachable from the front housing
Tray with lock for an easy fitting of the camera
Single-hand closing knob for back housing
Three M16x1 port for installation of accessories, e.g. vacuum valves or monitors
One M24x1 port for installation of accessories, e.g. monitor
Aluminum buttons and knobs and levers marked in the near with symbols identical to those of the machine in use
Wide back display viewfinder glass
Viewfinder
Dual O-Ring seals on all buttons and removable parts
Moisture sensor with LED and audible indicator (replaceable battery)
Removable port - 120mm bayonet
Ports security latch to prevent accidental opening
Wide, rubber covered feet for solid footing
M8 hole located on upper side of the housing for various accessories such as focus lights
Two M6 holes located on housing bottom side for different accessories such as brackets for strobes or tripods
External viewfinders can be mounted, INON compatible
Canon EOS R5 Underwater Housing X-2 R5 by INON
€3,190.00*
Underwater housing X-2 R5 by INON
A housing for Canon EOS R5
INON strobe compatible ultra-accurate multi-functional built-in "TTL Converter" as standard feature
Control flash amount directly from camera
12 shots/sec. continuous shooting supported
Equipped with “Quick Shoe System” for quick switch between horizontal and vertical camera composition
Standard “Vacuum Leak Sensor (PAT. P)" checks housing sealing in only 5 minutes
MRS port further evolves to support fine manual focusing
Optional two viewfinders provide bright and clear finder image
Lightweight and compact ultra-precision cast aluminum body
Ultra-accurate multi-functional built-in "TTL Converter"
The "TTL Converter" equipped as a standard feature, triggers INON strobe optically to enjoy fully automatic TTL. Exclusively developed for INON strobe based on its flash protocol to optimize its performance for underwater use. As an underwater strobe manufacturer, we successfully achieved the TTL Converter that provides constant, stable and highly accurate TTL exposure.
Strobe manual power is directly adjustable from camera
INON strobe manual power is directly adjustable from camera ranging between 1/64 and FULL at 1/3EV. increments. Useful when strobe is positioned away like on long strobe arm or when shooting with backlit technique.
12 shots/sec. continuous strobe firing *****
The TTL Converter fully supports [High speed continuous][High speed continuous+]. With ultra-accurate TTL shooting is now available for continuous shooting based on electricity stored in a capacitor6. INON TTL Converter strives efficiency in battery consumption not to miss precious moment and successfully provides more than 100,000 flash triggering only by two CR2032 coin batteries.
Built-in Quick Shoe System supports quick camera composition Change
The base plate is INON's unique Arca Swiss style "Quick Shoe Main Base".
The "Quick Shoe W50 Plate" on the bottom and side of the housing allows you to quickly change to vertical composition.
In addition to vertical composition without changing lighting position, it also allows you to shoot vertical composition from low angle which is not possible with conventional system.
Built-in "Vacuum leak sensor" confirms housing sealing in 5 minutes
The "Vacuum Leak Sensor" ensures housing sealing by monitoring air pressure inside of the housing during leak check and warns accidental flooding with LED blinks and buzzer during diving. The onboard pressure sensor changes sensitivity for leak check and diving by variable control program (PAT. P).
The supersensitive pressure sensor detects even fine leakage. Not as like conventional leak sensors, it drastically shortens test time (from 30 seconds to 5 minutes). The sensitivity of the dive mode eliminates false alarm even when ambient temperature changes.
New S-MRS Port
Newly developed S-MRS (Magnetic Rotary System) controls focusing and zooming by magnetic attraction. The new S-MRS provides smoother operation with less play or rattle comparing to the previous model. By combining the EOS R5 with an RF lens, the MF Peaking function can also be used during full-time manual focusing. Together with the focus guide function, this enables ultra-precise focusing.
Maximum three MRS Control Rings can be installed to control the Control Ring, Focus Ring and SA Control Ring.
Lightweight and compact ultra-precision cast aluminum body
The X-2 R5 is made from corrosion resistance aluminum alloy by ultraprecise cast manufacturing technique to fuse design, weight and durability in higher dimension.
The cast manufacturing technique enables thin body plate with complicated curved design which is not possible with machining. Lightweight and durable aluminum alloy body has acquired reliability, durability and controllability even in severe underwater.
Spare parts
Housing o-ring 90121
€25.00*
Spare O-ring for the following Nauticam housings:
NA-5DIII
NA-645DF
NA-6D
NA-70D
NA-D300
NA-D300S
NA-D700
NA-D800
NA-D81
NA-D600
NA-H4D
NA-R6
HDMI 2.0
Atomos Ninja V Underwater housing by Nauticam
€2,435.00*
With more cameras offering high quality HDMI video output, the Atomos Ninja V steps in, not only as a stunning monitor but also as a recorder of 4K 60p 4:2:2 10-bit video to on-board SSD drives in edit-friendly ProRes or Avid formats. The Nauticam NA-Ninja V, when used with supported housings and cameras, allows for the connection of the Ninja V over HDMI 2.0 in addition to providing easy access to the Ninja V controls underwater.
Atomos Ninja V
The Atomos Ninja V is an exceptional monitor, featuring a bright 1000 nit 10-bit HDR 5.2" screen that can display over 10 stops of dynamic range with compatible cameras. The monitor includes a variety of exposure and focus assist tools to insure your footage is properly exposed with critical focus. In addition to being an extremely capable monitor, the Ninja V is also a recorder. When used with compatible cameras over HDMI 2.0, the Ninja V can record 4K at 60p in 10-bit 4:2:2 ProRes or DNxHR formats to Atomos AtomX SSDmini solid state drives. With a 1TB SSDmini drive, the Ninja V can record up to 150 minutes of 4K video.
EXPOSURE TOOLS
The Ninja V exposure guides include a Waveform for luminance, RGB Parade for color balance, and Vector Scope for hue and saturation. These tools, especially useful for the underwater filmmaker, allow accurate and fast judging of exposure, even in the most uncooperative lighting scenarios. Even when recording Log or HDR footage, using Rec.709 or HLG monitoring displays the video on the screen adjusted to the levels of the chosen standard..
FOCUS TOOLS
Critical focus can be achieved using various peaking tools. Focus Peaking Color displays the original color image with the sharpest areas outlined in a selectable color. Focus Peaking Mono provides the same overlay but on a monochrome image. Focus Assist Outline shows only the false color outline on a black background of the sharpest Areas.
THE NAUTICAM NA-NINJA V UNDERWATER HOUSING
The Nauticam NA-Ninja V builds on the strong foundation Nauticam has built with previous Atomos monitor/recorder housings but is built around the new M28 large-bore bulkhead that supports HDMI 2.0.
The Ninja V is easily mounted in the housing, dropping in without trays or other mounting accessories and is held in place by two rotating locking levers. The Ninja V features both an HDMI 2.0 input as well as an output and the NA-Ninja V supports both as well. With dual M28 bulkheads, a second HDMI cable can be run to another monitor. The Ninja V allows for the application of. cube format 3D LUTs to this output signal.
The NA-Ninja V supports up to the NP-F970 size battery which provides up to two hours of run time. A CR-2032 battery powers the vacuum check and leak detection system. When used with the included Vacuum Valve, the system gives real-time feedback about the watertight integrity of the housing through an easily visible multi-color LED on the top of the housing.
Access to the touchscreen controls of the Ninja V are handled via a series of buttons and a selector knob beneath the screen of the housing including PLAY, REC, MON, RGB, PEAK and the Muti-Selector Lever.
HDMI 2.0 Cable M24D1R205-M28A1R170
€295.00*
This HDMI 2.0 cable is suitable for connecting the NA-XT3 and NA-R3/R5/R5C/R6/R7 or OM1 housing to the Ninja V underwater housing from Nauticam.
on stock
M24 Adaptor for HDMI 2.0 Cable (to use with 25087 with NA-A7RIV+SIII)
€55.00*
M24 Adaptor for HDMI 2.0 Cable (to use with 25087 with NA-A7RIV+SIII)
Atomos Ninja V (SDI) Underwater Housing by Nauticam
€2,660.00*
This version is suitable to accommodate the Atomos AtomX SDI module.
With more cameras offering high quality HDMI video output, the Atomos Ninja V steps in, not only as a stunning monitor but also as a recorder of 4K 60p 4:2:2 10-bit video to on-board SSD drives in edit-friendly ProRes or Avid formats. The Nauticam NA-Ninja V, when used with supported housings and cameras, allows for the connection of the Ninja V over HDMI 2.0 in addition to providing easy access to the Ninja V controls underwater.
Atomos Ninja V
The Atomos Ninja V is an exceptional monitor, featuring a bright 1000 nit 10-bit HDR 5.2" screen that can display over 10 stops of dynamic range with compatible cameras. The monitor includes a variety of exposure and focus assist tools to insure your footage is properly exposed with critical focus. In addition to being an extremely capable monitor, the Ninja V is also a recorder. When used with compatible cameras over HDMI 2.0, the Ninja V can record 4K at 60p in 10-bit 4:2:2 ProRes or DNxHR formats to Atomos AtomX SSDmini solid state drives. With a 1TB SSDmini drive, the Ninja V can record up to 150 minutes of 4K video.
EXPOSURE TOOLS
The Ninja V exposure guides include a Waveform for luminance, RGB Parade for color balance, and Vector Scope for hue and saturation. These tools, especially useful for the underwater filmmaker, allow accurate and fast judging of exposure, even in the most uncooperative lighting scenarios. Even when recording Log or HDR footage, using Rec.709 or HLG monitoring displays the video on the screen adjusted to the levels of the chosen standard..
FOCUS TOOLS
Critical focus can be achieved using various peaking tools. Focus Peaking Color displays the original color image with the sharpest areas outlined in a selectable color. Focus Peaking Mono provides the same overlay but on a monochrome image. Focus Assist Outline shows only the false color outline on a black background of the sharpest areas.
THE NAUTICAM NA-NINJA V UNDERWATER HOUSING
The Nauticam NA-Ninja V builds on the strong foundation Nauticam has built with previous Atomos monitor/recorder housings but is built around the new M28 large-bore bulkhead that supports HDMI 2.0.
The Ninja V is easily mounted in the housing, dropping in without trays or other mounting accessories and is held in place by two rotating locking levers. The Ninja V features both an HDMI 2.0 input as well as an output and the NA-Ninja V supports both as well. With dual M28 bulkheads, a second HDMI cable can be run to another monitor. The Ninja V allows for the application of. cube format 3D LUTs to this output signal.
The NA-Ninja V supports up to the NP-F970 size battery which provides up to two hours of run time. A CR-2032 battery powers the vacuum check and leak detection system. When used with the included Vacuum Valve, the system gives real-time feedback about the watertight integrity of the housing through an easily visible multi-color LED on the top of the housing.
Access to the touchscreen controls of the Ninja V are handled via a series of buttons and a selector knob beneath the screen of the housing including PLAY, REC, MON, RGB, PEAK and the Muti-Selector Lever.
on stock
M14 Vacuum Valve II
€205.00*
Installing vacuum valve to housing
Remove the plug of the M14 accessory port from the housing. Remove the cap from the vacuum valve. Tighten the vacuum valve to the housing with the tool provided.
Building up vacuum
Remove the cap of the vacuum valve. Connect the hand pump to the valve and pump several times until it reaches the target vacuum level. The LED light will turn flashing yellow while vacuum is building up, then steady green when the target vacuum level is reached.
Attention: After the target vacuum is reached, i.e. steady green light, attach the cap back to the vacuum valve.
It is recommended to leave the housing for at least 20mins to ensure it is sealed. If the LED light changes from steady green light to rapidly flashing yellow light, that means there is a leakage and please check every O-ring and conduct the vacuum test again.
Please ensure that the cap is attached back to the vacuum valve before going underwater.
Vacuum can be released by pushing the red release button.
Attention: Please DO NOT attempt to go over the designated vacuum level, i.e. stop pumping when the LED turn green. Excessive vacuum level may lead to the malfunction of the camera and lens.
Note: Although the vacuum indicator is designated to compensate for a certain amount of temperature variation, it is recommended to conduct the vacuum test in an environment where the temperature is stable.
After set up, the meaning of the LED indicator in the housing:
Flashing “Blue” light: Standby mode. The moisture alarm is active, and the system is ready for vacuum indication whenever a vacuum is detected.
Flashing “Red” light with beeping sound:Moisture is detected.
Flashing “Yellow” light: Some vacuum is detected, target vacuum level is not reached.
Steady “Green” light: Target vacuum level is reached.
Rapidly flashing “Yellow” light: Vacuum is dropping. (Will occur only after target vacuum level is reached)
Rapidly flashing “Red” light: Vacuum is totally lost. Circuit stalled until switched off. (Will occur only after target vacuum level is reached)
Stativplatte für NA-A7S/GH4/A7II/GH5/A9
€580.00*
Stativplatte, die an der Unterseite des Gehäuses befestigt wird und drei Standard 1 Zoll Kugelköpfe für Stativbeine oder anderes Zubehör bietet.
HINWEIS: Eignet sich nicht für die Cinema-Gehäuse von Nauticam
Control Kit for Canon Drop-In Filter Mount Adapter EF-EOS R
€235.00*
The Canon EF-EOS R adapter with control ring allows for the mapping of exposure functions to the control ring when using EF lenses. This gear allows for the use of this control ring within the NA-R housing from the left lower control dial.
Gear for Canon EF-EOS R Control Ring Mount Adaptor
€160.00*
The Canon EF-EOS R adapter with control ring allows for the mapping of exposure functions to the control ring when using EF lenses. This gear allows for the use of this control ring within the NA-R housing from the left lower control dial.
Monitor Housing Mounting Adaptor
€190.00*
This kit replaces the standard handle top plates to allow the mounting of Nauticam monitor housings to compatible Nauticam underwater housings.
on stock
Full Frame Angle Viewinder 32°/ 1:1
€1,590.00*
The next generation Nauticam Full Angle Straight Viewfinder is the perfect addition to your housing as it provides a bright, clear and undistorted 1:1 image of the camera’s viewfinder and is essential for precise focusing and artistic composition. This viewfinder is also available in an 0.8:1 version that can also accommodate viewing of the entire image field on cameras with larger EVFs such as the Sony A1.
The Full Frame Angle Viewfinder also provides more clearance for your regulator allowing for more a more comfortable viewing position, installs in seconds without tools and retains the hassle-free underwater dioptric adjustment feature. The viewfinder can also be rotated when using the camera in a portrait orientation.
INTRODUCING NAUTICAM FULL FRAME ANGLE VIEWFINDER 32°/ 1:1
For over a decade, Nauticam’s Enhanced Viewfinders have been known for superior optics, tack sharp performance and first-of-its-kind underwater dioptric adjustment. Anyone who has used these instruments has grown to appreciate what an asset they can be to any underwater photographer. But the camera world has seen radical changes in technology in the last ten years, including ever increasing size and resolution of Electronic Viewfinders (EVFs) found in the latest high-end mirrorless cameras. These newer EVFs challenge even the finest enhanced viewfinders for underwater housings.
In response to this technological evolution, Nauticam is excited to introduce the next generation of Enhanced Viewfinders designed to meet and exceed the requirements of all the current digital camera EVFs, as well as what is expected in the near future. The new Full Frame Straight Viewfinder employs entirely new optics to allow distortion free viewing without clipping the image frame. With the new viewfinders, reviewing images in playback or navigating the menus through the EVF has never been so easy.
32º/1:1 VS. 42º/0.8:1
Because different photographers have different needs and priorities, Nauticam offers the Full Frame Angle Viewfinder in two options. The 1:1 viewfinder option offers the most magnification available for underwater viewing while preserving the image field and surrounding data on most cameras. This viewfinder is a breakthrough in performance on high resolution EVFs and is an absolute joy on traditional DSLRs. The level of detail rendered is unequaled in the industry.
For those utilizing cameras with known EVF challenges such as the Sony’s A1 and A7SIII cameras, or just for the photographer who wants as much working room on the viewfinder field-of-view as possible, Nauticam offers the new 0.8:1 version. The 0.8:1 viewfinder offers an equally crisp and bright EVF display as the 1:1 viewfinder, with slightly less magnification for uncompromising corner to corner image viewing or better imaging of shooting data.
HASSLE-FREE UNDERWATER DIOPTRIC ADJUSTMENT
The much-loved dioptric adjustment is still featured and allows for easy eyesight adjustment in-water without disassembly of the viewfinder. as well as the simple installation and removal that takes only seconds.
TOOL FREE INSTALLATION
The Nauticam Full Frame Angle Viewfinder can be installed in seconds without any tools. The viewfinder is a direct replacement of the stock 0.66X viewfinder on DSLR and many full-frame mirrorless housings but requires an easily installed adapter on certain MIL housings. The viewfinder can also be rotated when using the camera in a portrait orientation.
Whether future proofing a viewfinder purchase for your current rig, or patiently waiting for a viewfinder worthy of the latest pro mirrorless camera you are diving, these cutting-edge viewfinders are the new industry standard to be looking at.
<iframe width="560" height="315" src="https://www.youtube-nocookie.com/embed/1AeT-02Mrdo?controls=0" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" allowfullscreen></iframe>
HDMI 1.4
Underwater Monitor WED-7 Pro
€1,568.00*
The WED-7 Pro is a professional HD monitor specially designed for underwater photographer.
The product is made of aluminum alloy, with carbon-fiber trim panels and delicate stainlesssteelchrome-plated buttons. It is High-end and professional product. The underwater monitor uses a full HD FHD display, plays for 4K HDMI input and outout,and is configuredwith a variety of auxiliary tools, so that the photographer is more freely and with ease in shooting.
Professional auxiliary shooting function: The product has a variety of professional shooting functions, such as: brightness histogram, audio column, auxiliary focus, false color, exposure prompt, monochrome display, nine grid, square, etc., all can better help the photographer effectively monitor and control the picture to the process of shooting and creating works.
Long back-up life: The product is powered by two 18650 lithium batteries, the longest working time can be up to 3.5 hours, and the product has a battery indicator light, so that the photographer can observe the battery power at any time.
4K signal transmission: The product supports 4K HDMI input and output, and high-definition pictures of the camera can be displayed on the monitor in real time through 4K signal transmission of HDMI.
7-inch FHD: The product features a 7-inch full HD screen with 1920x1200 resolution and 440PPI pixel density, as well as 500CD /m² high brightness and 1200:1 high contrast.
Ultra-wide viewing Angle: The choice of IPS display has an ultra-wide viewing Angle of 160°, which allows the photographer to easily get a clear picture when adjusting the position.
True color: The product uses the trustworthy Rec.709 high-definition color standard in the professional field, and accurately restore the color without distortion or color bias, it shows the real image.
Hood: The product design has a professional hood, so that the photographer can get the ideal viewing effect when using in the outdoor bright light.
Excellent image processing engine: the product is matched with an independent image processing engine, which improves the light and dark effect and contrast of the picture, so that the picture quality is more exquisite.
Excellent deep waterproofing effect: UP to 80m/263ft IP68 waterproofing grade: professional waterproofing design, full process technology and quality control, as well as real simulation of various deep water conditions of pressure testing.
on stock
HDMI (D-D) Cable in 200mm Length
€81.00*
This 200mm long HDMi (D-D) cable is designed for the internal connection from the HDMI bulkhead of the housing to the Fujifilm XT2/HX1/A6400 camera HDMI output.
on stock
WED-5 Underwater Monitor
€998.00*
5-inch HD Underwater Monitor by Weefine
A lightweight made of aluminium that is travel-friendly and practical. This is how the WED-5 underwater monitor from Weefine presents itself. With a brightness of just under 500 nits and 16.7 million colours, it allows you to fully assess your shots even in the water.
The monitor housing is milled from aluminium in the highest precision and then protected with a solid surface anodisation. This makes the monitor resistant to salt water and overheating.