THE OLYMPUS OM-D E-M5 MARK III CAMERA Weighing in at under one pound, the E-M5 Mark III packs an outsized punch. The E-M5 Mark III is built around the same 20Mp Live MOS sensor and Dual F.A.S.T Autofocus system as the larger OM-D E-M1 Mark II. New for the Mark III is the addition of a 121-point hybrid AF system which, combined with the powerful TruePic VIII processor allows for 10fps burst mode capture with AF-C. The Mark III's EVF has been upgraded to an OLED display with 60fps refresh rate. The 5-axis in-body stabilization also receives an 0.5 stop bump to 5.5EV. The E-M5 Mark III also steps up in the video category with DCI 4K at 24p or stabilized UHD 4K at 30p using the full width of the sensor to maintain field-of-view. HDMI output supports the 1.4 standard with 8-bit 4:2:2 at up to 30p quality. Key Camera Specs 20MP Live MOS Four Thirds Sensor 121-point Hybrid AF System 10 fps burst shooting with AF-C DCI 4K/24p and UHD 4K/30p video HDMI Output 5.5EV of image stabilization (CIPA-rating) 2.36M-dot OLED EVF With the OM-D E-M5 Mark III, Olympus brings a host of features from their flagship Four Thirds models into an economical and compact package that is ideal for the traveling image maker. THE NAUTICAM NA-EM5III UNDERWATER HOUSING The OM-D E-M5 Mark III places the power of the E-M1 Mark II in a compact travel-friendly package and so does the NA-EM5III. Building on our strong lineup of mirrorless camera housings, the NA-EM5III is a feature-rich underwater imaging tool. Our Mission Control design philosophy insures that critical controls are clearly labeled and easy to access with intuitive placement. The NA-EM5III is built around the extensive N85 port system. Optimized port solutions for a wide variety of Micro Four Thirds lenses and access to our Underwater Corrective Optics makes the Nauticam NA-EM5III a superior image-making platform. Stainless steel stiffening brackets and a shutter release extension, which are compatible with the optional Easitray II or Flexitray II tray systems are included with the NA-EM5III. An M10 threaded accessory mounting point is also ready to accept the optional M10 strobe mounting ball for additional accessory mounting flexibility. HDMI CONNECTIVITY A forward M16 bulkhead can be used for the optional HDMI 1.4 Bulkhead for use with external monitor housings such as the NA-502 or NA-502B for the SmallHD 502 and 502 Bright monitors. See sidebar for recommended configurations. VIEWFINDER OPTIONS The E-M5 mark III has an upgraded OLED Electronic Viewfinder. A clear view for fine focus and composition is critical for successful underwater photography, and nothing beats a magnifying viewfinder. These viewfinders use distance, not closeup vision, and provide a large, clear view of the high resolution Olympus electronic viewfinder. Available in Angled 45º (PN 32205) and Straight 180º (PN 32204) formats, both viewfinders have external dioptric adjustments for dialing in perfect correction matched to the photographer’s eyesight. RAPID FIRE OPTICAL FLASH TRIGGERING The E-M5 Mark III camera with the included FL-LM3 flash is limited to 2-3 fps continuous shooting, even when a low manual power is selected in the camera flash menu. In situations where continuous optical shooting is required, Nauticam’s Mini Flash Trigger for Olympus (26306) can trigger external strobes over fiber optic at up to 10 frames per second! The trigger is powered by onboard coin style lithium batteries, with thousands of flashes available from a set. The NA-EM5III comes fiber optic ready and accepts standard Sea & Sea style bushing connections. Nauticam Universal Fiber Optic cables provide exceptional light transmission for accurate TTL performance. Electrical triggering of legacy wired strobe systems is possible via an electrical Nikonos style bulkhead (optional). INTEGRATED VACUUM CHECK AND LEAK DETECTION SYSTEM The Nauticam vacuum check and leak detection system is available with NA-EM5III as standard equipment. Combined with an optional vacuum valve (NA25624 or NA25625), this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur.

The housing for Olympus OM-D E-M5 Mark II allows to capitalize on the camera full potential and to capture amazing pictures underwater. Product details An easy to use highly professional product has been created through techniques and innovations gained from years of experience. Easy access to all key/main camera controls, even with gloves, by means of clearly labelled lasered long life buttons. The back door has a large window glass for a fine camera display and optical viewfinder view and it is entirely detached from the front body to make easier the camera fitting. The housing stands with great stability due to sturdy and wide rubber feet located on the bottom. ONE HAND OPEN/CLOSE It's very easy to open and close Olympus OM-D E-M5 Mark II, without efforts by the user thanks to the upper helicoid and the bottom centered pins; the camera is placed easily into the housing on a sliding tray that keeps the camera robustly in place. PORTS AND EXTENSION RING A series of ports and extension rings are available in dedicated section. The removable port is fitted thanks to markers and a bayonet 102mm connection to the Olympus OM-D E-M5 Mark II housing. The interchangeable port bodies and extensions rings combine to allow the use of most of lenses on the market for maximum versatility and performance.  LIGHTING Two fiber optic connections are placed in front of the built-in flash and allow the use of external strobe. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such as anodized aluminum, which is anticorodal and thermo-coated, and stainless steel. A longlasting product that requires easy and simple maintenance by the user. Dual high precision and quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. Different accessories can be fitted by means of an M8 upper threaded hole, using the Isotta top handle or via the M6 and M8 threaded holes on the bottom. Controls ON/OFF of Olympus OM-D E-M5 Mark II; Own camera strobe open/close; Ergonomic camera focusing and shutter button for an easy use with gloves; Lens release; Rear control panel; Upper control panel;  All controls are available on the housing;

Compared to the previous OM-D E-M1, and all other Olympus Micro Four Thirds cameras, the E-M1 II is an improvement in every way. The new 20MP Live MOS sensor provides a useful bump in resolution. Dual quad core processors combine to allow 60 fps burst shooting (18 fps with autofocus). An incredibly advanced autofocus system (121 focus points covering 75-80% of the frame) grabs subjects instantly without hunting, and doesn’t let go when tracking. THE OLYMPUS OM-D EM1 MARK II It takes more than just headline grabbing specs on paper to make a great underwater camera system, and the E-M1 Mark II does many of the less obvious things right. The “2×2” dial and button structure doubles the functionality of the control dials and assignable push buttons. Typically these dials control shutter speed and aperture when shooting in manual mode, but with a flick of the 2×2 lever they are reassigned to other parameters (like ISO and Exposure Compensation, as an example). The control dials provide the easiest way to access frequently used camera settings directly, and Olympus has doubled their usefulness! It seems to be a trend among camera makers to sacrifice battery life and handling in an effort to to reduce overall size. Olympus didn’t make this mistake with E-M1 Mark II. The substantial hand grip provides exceptional handling, even with larger lenses, and makes space to accommodate a large battery that offers an exceptional 440 shots per charge (based on the CIPA rating, and many more are likely in real world use). Also new, and notable, is a high bitrate UHD (4K) video recording mode coupled with very capable image stabilization. The camera offers HDMI output to an external monitor, providing an upgraded display for framing, exposure check, and focus confirmation. KEY CAMERA SPECIFICATIONS 20MP Live MOS sensor 5-axis in-body image stabilization system 121-pt hybrid AF system 60 fps burst shooting (18 fps with continuous AF, 10 fps with flash) Fully articulating 3? LCD display High-res electronic viewfinder Cinema (DCI) and UHD 4K video 50MP High-Res Shot mode Weather-sealed body USB 3 (Type-C) THE NA-EM1II UNDERWATER HOUSING BY NAUTICAM A camera of this caliber deserves an exceptional underwater housing. Five and a half years ago, Nauticam entered the Micro Four Thirds underwater housing segment. 17 housing models later, Nauticam is proud to have produced more mirrorless underwater camera housings than any other manufacturer. The Nauticam NA-EM1II isn’t a new design, it is a refinement of the housings that have come previously. The system is field tested, and underwater photographer approved. The housing is small, but not at the expense of functionality or ergonomics. Integrated handles provide a sturdy and comfortable base to operate the system from. An ergonomic shutter release lever, thumb lever for AE-L / AF-L, and well placed control dials provide the same operational feel as any Nauticam DSLR housing. Control buttons are placed within easy reach of the handles, with sufficient spacing to allow easy operation, even by feel. The ergonomic experience of this system is clearly influenced by Nauticam DSLR systems, with class leading control access and feel. More than just good looking, this is a rugged housing, ready to tackle thousands of hours of underwater abuse. Crafted from solid aircraft aluminum, the housing can reach depths of 100m with ease. The secure single rotating housing latch opens the housing back. The camera drops in easily. The rear mounted housing o-ring makes maintenance simple. Dual fiber optic synch ports are standard and take advantage of the camera included FL-LM3 flash for strobe triggering. To make the most of the E-M1 Mark II’s excellent electronic view finder (EVF), Nauticam allows for installation of the acclaimed 45º and 180º magnified viewfinders, providing the ultimate in composition and focus ability. The NA-EM1II is a professional grade underwater housing, supporting the pro-level E-M1 II camera body to its full potential. PREMIUM PROFESSIONAL OPTICS It’s all about the glass, and lenses are the key to terrific photography. This has always been a strength of Olympus systems, and the lineup is now stronger than ever thanks to the Nauticam Wet Wide Lens (WWL-1). WWL-1, paired with an Olympus 14-42mm f/3.5-5.6 EZ Lens or ED 12-50mm F3.5-6.3 EZ*, provides a full zoom through ultra wide angle field of view. In our tests, this combination exceeds the corner sharpness and clarity of even very good micro four thirds wide angle lenses behind dome ports. WWL-1 will focus on its front element for unmatched close focus wide angle performance, and full zoom through means you can zoom to crop in camera for tighter framing. WWL-1 is mounted via a quick change bayonet system that allows fast and easy one handed mounting and removal. An optional lens caddy provides a place to park the WWL-1 lens when not in use. For closeup and macro work, the Nauticam Compact Macro Converter (CMC-1, PN 81301) allows images smaller than 1? wide to be captured. Ultra wide, mid-range and macro imaging capability, all on the same dive! There are many more options for the underwater photographer, including any of the several 14-42mm options, the Panasonic Lumix G X VARIO 12-35mm F2.8 ASPH. POWER O.I.S., Olympus M.ZUIKO DIGITAL ED 12-40mm f/2.8 PRO, Panasonic Lumix G Vario 12-32mm f/3.5-5.6 ASPH, Panasonic Lumix G 14mm F2.5 ASPH, and the Leica DG Macro Elmarit 45mm F2.8 ASPH. *12-50 is usable with WWL-1 from approximately 15.5mm – 50mm with WWL-1. VIEWFINDER OPTIONS  A clear view for fine focus and composition is critical for successful underwater photography, and nothing beats a magnifying viewfinder. These viewfinders use distance, not closeup vision, and provide a large, clear view of the high resolution Olympus electronic viewfinder. Available in Angled 45º (PN 32205) and Straight 180º (PN 32204) formats, both viewfinders have external dioptric adjustments for dialing in perfect correction matched to the photographer’s eyesight. INTEGRATED VACUUM CHECK AND LEAK DETECTION SYSTEM The Nauticam vacuum check and leak detection system is available with NA-EM1II as standard equipment. Combined with an optional vacuum valve (PN 25624), this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. FLASH CONNECTORS FOR OPTICAL TTL Reliable automatic flash exposure is available with the NA-EM1II and a variety of optically fired flashes. The Inon Z-240, D-2000, S-2000, and Sea & Sea YS-D1/YS-D2 strobes provide automated lighting, precisely reproducing the camera’s FL-LM3 flash at a proportionally greater intensity. This system yields accurate automatic TTL flash performance – even in manual exposure mode – with no electrical sync cables to flood! The NA-EM1II comes fiber optic ready and accepts standard Sea & Sea style bushing connections. Nauticam Fiber Optic cables, available for both Inon and Sea & Sea strobes, provide exceptional light transmission for accurate TTL Performance. RAPID FIRE OPTICAL TRIGGERING The E-M1 Mark II camera with FL-LM3 flash is limited to 2-3 fps continuous shooting, even when a low manual power is selected in the camera flash menu. In situations where continuous optical shooting is required, Nauticam’s Mini Flash Trigger (26306) can trigger external strobes over fiber optic at up to 10 frames per second! The trigger is powered by onboard coin style lithium batteries, with thousands of flashes available from a set. Electrical triggering of legacy wired strobe systems is possible via an electrical Nikonos style bulkhead (optional).

The housing for Olympus OM-D E-M1 Mark II allows to capitalize on the camera full potential and to capture amazing pictures underwater. Product details An easy to use highly professional product has been created through techniques and innovations gained from years of experience. Easy access to all key/main camera controls, even with gloves, by means of clearly labelled lasered long life buttons. The back door has a large window glass for a fine camera display and optical viewfinder view and it is entirely detached from the front body to make easier the camera fitting. The housing stands with great stability due to sturdy and wide rubber feet located on the bottom. Ergonomic side handles are included. ONE HAND OPEN/CLOSE It's very easy to open and close Olympus OM-D E-M1 Mark II, without efforts by the user thanks to the upper helicoid and the bottom centered pins; the camera is placed easily into the housing on a sliding tray that keeps the camera robustly in place. PORTS AND EXTENSION RING A series of ports and extension rings are available in dedicated section. The removable port is fitted thanks to markers and a bayonet 102 mm connection to the Olympus OM-D E-M1 Mark II housing. The interchangeable port bodies and extensions rings combine to allow the use of most of lenses on the market for maximum versatility and performance.  LIGHTING Two fiber optic connections are placed in front of the built-in flash and allow the use of external strobe. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such as anodized aluminum, which is anticorodal and thermo-coated, and stainless steel. A longlasting product that requires easy and simple maintenance by the user. Dual high precision and quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. Different accessories can be fitted directly on the handles or by means of an M8 upper threaded hole, using the Isotta top handle or via the M6 and M8 threaded holes on the bottom. Controls ON/OFF of Olympus OM-D E-M1 Mark II; Own camera strobe open/close; Ergonomic camera focusing and shutter button for an easy use with gloves; Lens release; Rear control panel; Upper control panel; All controls are available on the housing;

The housing for Olympus OM-D E-M1 Mark III allows to capitalize on the camera full potential and to capture amazing pictures underwater. Product details An easy to use highly professional product has been created through techniques and innovations gained from years of experience. Easy access to all key/main camera controls, even with gloves, by means of clearly labelled lasered long life buttons. The back door has a large window glass for a fine camera display and optical viewfinder view and it is entirely detached from the front body to make easier the camera fitting. The housing stands with great stability due to sturdy and wide rubber feet located on the bottom. Ergonomic side handles are included. ONE HAND OPEN/CLOSE It's very easy to open and close Olympus OM-D E-M1 Mark III, without efforts by the user thanks to the upper helicoid and the bottom centered pins; the camera is placed easily into the housing on a sliding tray that keeps the camera robustly in place. PORTS AND EXTENSION RING A series of ports and extension rings are available in dedicated section. The removable port is fitted thanks to markers and a bayonet 102 mm connection to the Olympus OM-D E-M1 Mark III housing. The interchangeable port bodies and extensions rings combine to allow the use of most of lenses on the market for maximum versatility and performance.  LIGHTING Two fiber optic connections are placed in front of the built-in flash and allow the use of external strobe. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such as anodized aluminum, which is anticorodal and thermo-coated, and stainless steel. A longlasting product that requires easy and simple maintenance by the user. Dual high precision and quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. Different accessories can be fitted directly on the handles or by means of an M8 upper threaded hole, using the Isotta top handle or via the M6 and M8 threaded holes on the bottom. Controls ON/OFF of Olympus OM-D E-M1 Mark III; Own camera strobe open/close; Ergonomic camera focusing and shutter button for an easy use with gloves; Lens release; Rear control panel; Upper control panel; All controls are available on the housing;

The housing for Olympus OM-D E-M5 Mark II allows to capitalize on the camera full potential and to capture amazing pictures underwater. Product details An easy to use highly professional product has been created through techniques and innovations gained from years of experience. Easy access to all key/main camera controls, even with gloves, by means of clearly labelled lasered long life buttons. The back door has a large window glass for a fine camera display and optical viewfinder view and it is entirely detached from the front body to make easier the camera fitting. The housing stands with great stability due to sturdy and wide rubber feet located on the bottom. ONE HAND OPEN/CLOSE It's very easy to open and close Olympus OM-D E-M5 Mark II, without efforts by the user thanks to the upper helicoid and the bottom centered pins; the camera is placed easily into the housing on a sliding tray that keeps the camera robustly in place. PORTS AND EXTENSION RING A series of ports and extension rings are available in dedicated section. The removable port is fitted thanks to markers and a bayonet 102mm connection to the Olympus OM-D E-M5 Mark II housing. The interchangeable port bodies and extensions rings combine to allow the use of most of lenses on the market for maximum versatility and performance.  LIGHTING Two fiber optic connections are placed in front of the built-in flash and allow the use of external strobe. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such as anodized aluminum, which is anticorodal and thermo-coated, and stainless steel. A longlasting product that requires easy and simple maintenance by the user. Dual high precision and quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. Different accessories can be fitted by means of an M8 upper threaded hole, using the Isotta top handle or via the M6 and M8 threaded holes on the bottom. Controls ON/OFF of Olympus OM-D E-M5 Mark II; Own camera strobe open/close; Ergonomic camera focusing and shutter button for an easy use with gloves; Lens release; Rear control panel; Upper control panel;  All controls are available on the housing;

The housing for Olympus OM-D E-M5 Mark III allows to capitalize on the camera full potential and to capture amazing pictures underwater. The Underwater housing for Olympus E-M5 Mark II by Isotta An easy to use highly professional product has been created through techniques and innovations gained from years of experience. Easy access to all key/main camera controls, even with gloves, by means of clearly labelled lasered long life buttons. The back door has a large window glass for a fine camera display and optical viewfinder view and it is entirely detached from the front body to make easier the camera fitting. The housing stands with great stability due to sturdy and wide rubber feet located on the bottom. ONE HAND OPEN/CLOSE It's very easy to open and close Olympus OM-D E-M5 Mark III, without efforts by the user thanks to the upper helicoid and the bottom centered pins; the camera is placed easily into the housing on a sliding tray that keeps the camera robustly in place. PORTS AND EXTENSION RING A series of ports and extension rings are available in dedicated section. The removable port is fitted thanks to markers and a bayonet 102mm connection to the Olympus OM-D E-M5 Mark III housing. The interchangeable port bodies and extensions rings combine to allow the use of most of lenses on the market for maximum versatility and performance.  LIGHTING Two fiber optic connections are placed in front of the built-in flash and allow the use of external strobe. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such as anodized aluminum, which is anticorodal and thermo-coated, and stainless steel. A longlasting product that requires easy and simple maintenance by the user. Dual high precision and quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. Different accessories can be fitted by means of an M8 upper threaded hole, using the Isotta top handle or via the M6 and M8 threaded holes on the bottom. Controls ON/OFF of Olympus OM-D E-M5 Mark III Own camera strobe open/close Ergonomic camera focusing and shutter button for an easy use with gloves Lens release Rear control panel Upper control panel All controls are available on the housing Product Highlights Two fiber optic connectors One M16 port for installation of accessories, e.g. vacuum valves or monitors Back housing completely separable from the front housing Tray with lock for the easy insertion of the camera Single-hand closing knob for back housing Aluminum buttons and dials with engraved symbols identical to camera controls Wide back display viewfinder glass with optical viewfinder Double o-ring seal on all buttons and removable parts Moisture sensor with LED indicator (replacable battery) Removable port - 102mm bayonet Ports security latch to prevent accidental opening Wide, rubber covered feet for solid footing on boat floors or sea floor M8 hole located on upper side of the housing for various accessories such as focus lights Two M6 holes located on housing bottom side for different accessories such as brackets for strobes or tripods External viewfinders can be mounted, INON X-2 compatible

The OM Systems OM-1, the first high-end Micro Four Thirds mirrorless camera from OM Digital Solutions. The OM-1 features a 20MP quad-pixel AF stacked CMOS sensor.  It is paired with the latest TruePic X processor to deliver 3x faster processing speeds and is capable of 120 fps shooting with the electronic shutter. The O-M1 can also capture 4K UHD or DCI at 60p in the OM-Log profile for great color grading range. The OM-1 camera by Olympus OM Systems has announced the OM-1. The new camera is supposed to top all previous models and have the absolute "WOW factor". Autofocus, image stabiliser and processor are said to be convincingly better. It will be available from the beginning of March. The OM-1 is to be the new MFT flagship from Olymus. With its 20MP sensor, it is said to be capable of 120 frames/s at full resolution. It also has an extremely fast image sensor. OM System promises that subject tracking and autofocus tracking will be faster and better than ever before. But there's also been a big upgrade in the image stabiliser. Key Camera Specs 20MP Stacked CMOS Sensor 1053 X-type AF points Up to 120 fps with electronic shutter Image stabilization rated to 7EV of correction (up to 8EV with compatible lenses) Large 5.76M-dot OLED electronic viewfinder Dual UHS-II SD card slots UHD or DCI 4K/60p video, 1080 up to 240 fps Weather sealing rated to IP53 Olympus OM-1 underwater housing by Nauticam The OM Systems OM-1 is characterized by its combination of extreme customizability and impressive stabilization in a compact hybrid-shooting package. The Nauticam NA-OM1, similar to the OM-1 is a refinement of it's predecessors. Nauticam has produced housings for wide range of Micro Four Thirds cameras from Olympus and Panasonic. Throughout the evolution of Micro Four Thirds cameras, Nauticam has adapted our design to help image makers get take full advantage of every camera advancement. More than a simple waterproof case, the NA-OM1 integrates with the OM-1 to adapt and improve upon the camera's features for underwater shooting. MISSION CONTROL Regardless of where a dial or button may be found on the camera body, Nauticam engineers make sure it is located where it is needed most on the housing. This Mission Control philosophy drives the design of every housing and provides for the most intuitive and easy to use housings available. The NA-OM1 features a thumb lever, easily accessed from the ergonomic rubberized right handle that actuates the AF-ON control.  This back-button autofocus method prevents the camera from refocusing between shots, allowing the user fine control over a shot's focus and is critical whether shooting macro or fast moving wide-angle subjects. FLASH TRIGGERING The OM-1 can be used with the optional Olympus FL-LM3 flash inside the NA-OM1 underwater housing by Nauticam to provide accurate TTL flash triggering through the integrated Sea&Sea style fiber optic bulkheads. For high-speed manual flash triggering, the optional Mini Flash Trigger for Olympus (26306) can be used. The trigger is powered by onboard coin style lithium batteries, with thousands of flashes available from a set. Electrical triggering of legacy wired strobe systems is possible via an electrical Nikonos style bulkhead (optional). PREIUM PROFESSIONAL OPTICS A camera system is only as good as the optics placed in front of it. Nauticam's extensive line of dome and flat ports support a wide variety of Micro Four Thirds lenses. For even higher image quality and versatility, the NA-OM1 can be used in conjunction with Nauticam's lineup of Water Contact Optics. For example, with the Olympus 14-42mm f/3.5-5.6 EZ Lens, the Nauticam WWL-1 provides a full zoom through ultra wide-angle 130º field of view. MAGNIFYING VIEWFINDERS A clear view for fine focus and composition is critical for successful underwater photography, and nothing beats a magnifying viewfinder. These viewfinders use distance, not closeup vision, and provide a large, clear view of the high resolution Olympus electronic viewfinder. Available in Angled 45º (PN 32205 or 32213) and Straight 180º (PN 32204 or 32211) formats, both viewfinders have external dioptric adjustments for dialing in perfect correction matched to the photographer’s eyesight.  The Full Frame Angle Viewfinder 32°/ 1:1 (32213) or the Full Frame Straight Viewfinder 32°/ 1:1 (32211) requires the 32215 Viewfinder Collar Adaptor. INTEGRATED VACUUM CHECK AND LEAK DETECTION SYSTEM The Nauticam Vacuum check and leak detection system is available with NA-OM1 Underwater Housing as standard equipment. Combined with an optional vacuum valve (PN 25624), this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur.

The AOI UH-EPL10-WHT body kit is designed to accommodate the Olympus PEN E-PL9 or E-PL10 cameras equipped with the M.ZUIKO DIGITAL ED 14-42mm F3.5-5.6 EZ kit lens. The AOI UH-EPL10-WHT set includes: UH-EPL10-WHb underwater housing FLP-06 Flat port LG-OM-1442EZ Lens zoom ring The AOI UH-EPL10 underwater housing at a glance Why compromise when you can have it all? The AOI UH-EPL10 underwater housing for the Olympus PEN E-PL9 and E-PL10 cameras allows you to get more out of your underwater photography system than ever before and at a great price! It's tough and durable, yet lightweight and compact. With added vacuum protection, it's practical yet ergonomic and stylish. It's ready to go* and as easy to use as a point-and-shoot camera, yet packed with extra features that make professional photography possible. Want even more? Simply add one of the many additional accessories offered by AOI to enhance your UH-EPL10 housing system and meet your photography needs. Designed specifically for Olympus' successful PEN camera range, the AOI UH-EPL10 housing is the perfect underwater companion for your camera, making it convenient and easy to get the most out of it. *Camera not included in housing box. Features of the AOI UH-EPL10 underwater housing Durable, shockproof design Lightweight and compact Added protection with a vacuum analysis and humidity warning system (VWS) and secure locking mechanism Optical flash trigger conserves the camera's battery and eliminates the need to use the in-camera flash Advanced ergonomics allow use even with gloves with thumb rest, finger grip and accessible controls including an extended shutter release lever Clearly labelled controls allow full access to essential camera functions Ready to use out of the box, including body, lens mount and lens accessories. Full accessory pack available: Compatible with most popular underwater housing accessories that use these connection points: 1/4'' tripod thread, hot shoe mount, LCD monitor aperture rails, strap loops, 67mm lens mount thread, QRS slots and fibre optic cable connectors. An underwater housing that grows with your capabilities: Discover expanded possibilities with dedicated camera lenses and AOI's PEN-mount lens mounts using the UH-EPL10 housing design with interchangeable lens mounts. About the Olympus PEN E-PL10 mirrorless camera: Step up to the PEN E-PL10. This super-compact, lightweight camera is comfortable to carry and designed for a sleek and timeless feel. Advanced technology ensures you can capture stunning photos and smooth 4K video.This camera is designed to help you create and capture your vision. Thanks to built-in Wi-Fi and Bluetooth connectivity, you can easily share your work on the go. 180° swivel touchscreen 4K Ultra HD video Wi-Fi & Bluetooth sharing 16-megapixel live MOS image sensor 3-axis image stabilisation TruePic VIII image processor Built-in flash Touch for focus & shutter release Silent shooting mode A CAMERA THAT LOOKS GOOD ON YOU: A timeless design with high-quality materials and classic colour combinations that complement any style so you always look your best. HIGH QUALITY MATERIALS: The PEN E-PL10 combines pure aesthetics and stylish design with materials such as leather, brushed aluminium and metal textures. THREE COMPLEMENTARY COLOURS: Choose from three colours to suit any style. Try our new sleek, all-black look with matching body and lens. COMPACT AND LIGHTWEIGHT: Transporting this camera is so refreshingly easy that you can take it anywhere. A lightweight body and compact lenses provide portability that only Olympus can offer. Specifications of the Olympus PEN E-PL10 camera: Sensor Effective resolution / type: 16.1 megapixel live MOS Processor: TruPic VIII Focusing system: Contrast detection with 121 focus points Image stabilisation system: In-body 3-axis image stabilisation Rear monitor: 3.0" 180° swivel touch LCD Creative features: Live composite, selfie mode, selfie video mode, video clip mode, advanced photo (AP) mode. Sequential shooting speed: 8.6 fps [H mode], 4.8 fps [L mode] Mechanical shutter Special features: Easy image sharing via Bluetooth Low Energy, Wi-Fi and Olympus Image Share app; built-in pop-up flash sensor / dust reduction. Sensor type: 4/3" Live MOS sensor Effective pixels: 16.1 million Total pixels: 17.2 million Filter Array: Primary colour filter (RGB) Aspect Ratio & Area: 4:3 / 17.4 x 13.0 mm Dust Reduction: Super Sound Wave Filter Processor Type: Olympus TruePic VIII AF System Type: High Speed Imager AF (Contrast Detection) Focus modes: Single AF (S-AF) / Continuous AF (C-AF) / Manual Focus (MF) / S-AF + MF / AF Tracking (C-AF + TR) Full-time AF: Full-time AF Weight* Approx. 380g (with BLS-50 battery and memory card, based on CIPA standards) Approx. 332g (body only) Dimensions: 117.1mm (W) X 68mm (H) X 39mm (D) Operating temperature range: 0 ~ +40°C (operation) / -20 ~ +60°C (storage) Operating humidity range: 30 - 90% (operation) / 10 - 90% (storage) Box Contents: Case, USB cable, shoulder strap, user manual, Warranty card, BLS-50 lithium-ion battery, BCS-5 lithium-ion battery charger 

The AOI UH-EPL10-WHT housing set is designed to accommodate Olympus PEN E-PL9 or E-PL10 cameras equipped with the M.ZUIKO DIGITAL ED 14-42mm F3.5-5.6 EZ kit lens. The AOI UH-EPL10-WHT housing set is designed to accommodate Olympus PEN E-PL9 or E-PL10 cameras equipped with the M.ZUIKO DIGITAL ED 14-42mm F3.5-5.6 EZ kit lens. The AOI UH-EPL10-WHT kit includes: UH-EPL10-WHb underwater housing FLP-06 flat port LG-OM-1442EZ Lens zoom ring The AOI UH-EPL10 underwater housing at a glance Why compromise when you can have it all? The AOI UH-EPL10 underwater housing for the Olympus PEN E-PL9 and E-PL10 cameras allows you to get more out of your underwater photography system than ever before, and at a great price! It's tough and durable, yet lightweight and compact. With additional vacuum protection, it is practical yet ergonomic and elegant. The camera is ready to go* and as easy to use as a point-and-shoot camera, yet packed with additional features that enable professional photography. Want even more? Simply add one of the many additional accessories offered by AOI to enhance your UH-EPL10 housing system and meet your photography needs. The AOI UH-EPL10 housing has been specifically designed for Olympus' successful PEN camera range and is the perfect underwater companion for your camera, making it convenient and easy to get the most out of it. . *Camera not included in the housing box. Features of the AOI UH-EPL10 underwater housing Durable, shock-resistant design. Lightweight and compact Additional protection with a vacuum analysis and humidity warning system (VWS) and secure locking Optical flash output conserves the camera's battery and eliminates the need to use the camera's internal flash. Advanced ergonomics allow use even with gloves with thumb rest, finger grip and accessible controls including extended release lever Clearly marked controls allow full access to essential camera functions Instantly ready to use, including housing, lens mount and lens accessories Complete accessory pack available: Compatible with most common underwater gear accessories that use these connection points: 1/4'' tripod thread, hot shoe mount, LCD monitor aperture rails, strap loops, 67mm lens mount thread, QRS slots and fibre optic cable connectors. An underwater gear that grows with your capabilities: Discover advanced possibilities with dedicated camera lenses and AOI's PEN mount lens adapters using the UH-EPL10 housing design with interchangeable lens adapters. &Um;ber the Olympus PEN E-PL10 mirrorless camera: Switch to the PEN E-PL10. This super-compact, lightweight camera is comfortable to carry and designed for a slim and timeless feel. Advanced technology ensures you can capture stunning photos and smooth 4K video. This camera is designed to help you create and capture your vision. With built-in Wi-Fi and Bluetooth connectivity, you can easily share your work on the go. 180° swivel touchscreen. 4K Ultra HD video Wi-Fi & Bluetooth sharing 16-megapixel live MOS image sensor 3-axis image stabilisation TruePic VIII image processor Built-in flash Focus & release guide Silent shooting mode A CAMERA THAT LOOKS GOOD ON YOU: A timeless design with high-quality materials and classic colour combinations that complement any style so you always look your best. HIGH QUALITY MATERIALS: The PEN E-PL10 combines pure Ästhetics and stylish design with materials like leather, brushed aluminium and metal textures. Three complementary colours: Choose from three colours to suit any style. Try our new sleek, all-black look with matching case and lens. COMPACT AND LIGHTWEIGHT: Carrying this camera is so refreshingly easy, you can take it anywhere. A lightweight body and compact lenses provide portability only Olympus can offer. Specifications of the Olympus PEN E-PL10 camera: Sensor Effective Resolution / Type: 16.1 megapixel Live MOS Processor: TruPic VIII Focusing system: contrast detection with 121 focus points. Image stabilisation system: In-body 3-axis image stabilisation Rear-side monitor: 3.0" 180° tiltable touch LCD Creative features: Live composite, Selfie mode, Selfie video mode, Video clip mode, Advanced photo (AP) mode Sequential shooting speed: 8.6 fps [H mode], 4.8 fps [L mode] Mechanical shutter Special features: Easy image sharing üvia Bluetooth Low Energy, Wi-Fi and Olympus Image Share App; built-in pop-up flash sensor / dust reduction Sensor type: 4/3" Live MOS sensor Effective pixels: 16.1 million Total pixels: 17.2 million Filter array: Primärer colour filter (RGB) Aspect Ratio & Area: 4:3 / 17.4 x 13.0 mm Dust reduction: Super sound wave filter Processor type: Olympus TruePic VIII AF system type: high-speed imager AF (contrast detection) Focus modes: Single AF (S-AF) / Continuous AF (C-AF) / Manual Focus (MF) / S-AF + MF / AF Tracking (C-AF + TR) Full-time AF: Full-time AF Weight.* Approx. 380g (with BLS-50 battery and memory card, based on CIPA standards) Approx. 332g (body only) Dimensions: 117.1 mm (W) X 68 mm (H) X 39 mm (D) Operating temperature range: 0 ~ +40°C (operating) / -20 ~ +60°C (storage) Operating humidity range: 30 - 90% (operation) / 10 - 90% (storage) Box contents: case, USB cable, shoulder strap, user manual, Warranty card, BLS-50 lithium-ion battery, BCS-5 lithium-ion battery charger.

THE OLYMPUS TOUGH TG-6 CAMERA The Olympus TG-6 shares the same 12MP BSI CMOS sensor with the TruePic VIII quad-core processor. The camera itself is IP6X rated to be waterproof up to 50ft (which is actually IPX8 spec!) as well as crushproof to 220lbf and freezeproof to 14º F and features an upgraded rear LCD screen. The feature that made the TG-5 a true macro game-changer was the 1cm minimum focus distance. For the TG-6, this feature has seen stronger implementation through the ability to use it outside of the dedicated Microscope Mode. Key Camera Specifications 12MP BSI CMOS sensor Waterproof to 50ft 4K/30p UHD Video Capture 1080/120p FHD High-speed Video Capture Selectable Underwater White Balance Modes SELECTABLE AUTOFOCUS MODES On the TG-5, in order to take advantage of the camera's ability to focus at a mere 1cm from the lens to capture true super-macro images, the camera needed to be set to the dedicated Microscope Mode which forced the camera into a wider-open aperture. The resulting images had impressive magnification but there was no control over the depth-of-field and significant ambient light intrusion. With the TG-6, there is now a selectable Super Macro Focus mode available in Aperture Priority Mode. This gives the shooter complete control over Aperture. Combined with the added ability to set a minimum shutter speed as high as 1/500sec and limiting the maximum ISO, it is possible to regain control over both the depth-of-field and render clean black backgrounds free of ambient light. UNDERWATER WHITE BALANCE SETTINGS While the TG-5 did feature an underwater white balance setting, the TG-6 now allows for even greater differentiation with depth-specific preset white balances. for shallow, mid-depth, and deep. These can be used inside the Aperture Priority mode and are helpful when shooting scenes lit purely by ambient light. VIDEO PERFORMANCE UPGRADES The 4K/30p video option can now be selected from the Quick Menu as opposed to switching the cameras Mode Dial over to Movie Mode. This combined the with the dedicated Super Macro Focus mode brings all the benefits listed above for still images to 4K video capture as well, all within the underwater-friendly Aperture Priority mode. THE NAUTICAM NA-TG6 UNDERWATER HOUSING Nauticam has supported the Olympus Tough series continuously since the TG-3. Despite the camera being waterproof on its own, the addition of a machined aluminum Nauticam housing transitions the TG-6 into a true underwater image-making platform. Access to essential controls is not only translated into the housing but improved with large well-placed and clearly labeled buttons and dials. The NA-TG6 is compatible with both the TG-5 and TG-6 camera models. INTEGRATED BAYONET MOUNT The NA-TG6 comes with an integrated Bayonet Mount which will work with all previous Bayonet Mount accessories as well as the new WWL-C Wet Wide Lens for compact camera systems. The WWL-C is designed to bring true underwater-specific ultra-wide angle performance to 24mm equivalent lenses such as that found on the TG-5 and TG-6 cameras. The WWL-C in a low-profile wet-mate corrective optic that delivers 130º field-of-view with full zoom-through capability. The lens can easily be removed underwater when macro situations arise and securely stored with one of the Nauticam Bayonet Mount storage solutions. ACCESSORY MOUNTING OPTIONS With the Nauticam NA-TG6 there are both a cold-shoe and M10 threaded mounting point on the housing. These can be outfitted to support a variety of lighting accessories. If even more flexibility is needed, the housing ships with a set of stainless steel stiffening brackets and a shutter release extension for use with the Nauticam Flexitray II system. The addition of the tray, an Adjustable Right Handle and optional Strobe Mounting Balls (71311) creates an even more stable shooting platform with up to four accessory mounting locations. NOTE: When using with 71207 Flexitray II, the baseplate must be rotated 180º and the handles adjusted accordingly. FLASH TRIGGERING The NA-TG6 is able to transmit the camera's internal flash to supported external strobes via Nauticam Universal Fiber Optic Cables which plug directly into the Sea&Sea style bulkheads on the front of the housing. The included diffuser can also be attached to use the internal flash as the primary light source. LCD MAGNIFIER The NA-TG6 can be outfitted with Rails (25123) above and below the rear LCD display window that can accommodate the LCD Magnifier with Dioptric Adjustment (25106). The magnifier not only functions as a shade to assist in bright shooting conditions it can magnify the screen to help judge critical focus. The magnifier features a dioptric adjustment to set the focus for your vision, even when using a prescription mask.

The Weefine WFH-TG6 for the Olympus TG5/TG6/TG7 is an outstanding example of the next generation of high-end housings for compact cameras. With excellent fit and finish, rugged construction, and meticulous attention to detail, all in a user friendly sized package, this is a beautifully executed housing. Ergonomic command dials make this housing a joy to use. An easy to use, highly professional product has been created through techniques and innovations gained from years of experience. The housing for Olympus Tough! TG5/TG6 perfect handling by means of an adjustable strips. Easy access to all key/main camera controls by means of clearly labelled laser-engraved longlasting buttons. The back door has a large window for a fine camera display view and it is entirely detached from the front body to make easier the camera fitting. ONE HAND OPEN/CLOSE It?s very fast to open and close Olympus Tough! TG6/TG6, without any efforts by the user thanks to the side helicoid screw and the bottom centered pins. The housing stands with great stability due to sturdy and wide rubber feet located on the bottom. PORT, CLOSE-UP AND WIDE-ANGLE LENSES The housing for Olympus Tough! TG6/TG6 ends with a tempered glass optic and features a M52 thread mount that allows the use of additional wide angle lens and macro lens. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such anodized aluminum which is anticorodal and thermo-coated and stainless steel. A longlasting product that requires easy and simple maintenance by the user. So small and so rich in technology! Dual high precision and quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; an alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. An hole positioned on the bottom allows to secure the housing for Olympus Tough! TG-5/TG6 with a strap. Different accessories can be fitted by means of an upper sliding tray and double threaded NC1/4 holes on the bottom. BUILT-IN VACUUM SYSTEM Weefine Smart Housing has vacuum leak check circuitry and valve built-in. Just use the included pump to secure your housings against leaks before your dive. Vacuum system lets yuou clearly know if the housing is sealed before diving. This is important to keep yourdevices safe.

THE NA-TG-5 HOUSING (M52) The NA-TG5 brings legendary Nauticam durability and ergonomics to the Olympus TG-5 and TG-6. The milled aluminum housing incorporates features pioneered in the SLR, mirrorless and digital cinema lines. All of the camera controls are clearly labeled, and the video record button is easily identified by shape and color. The proven rotary locking latch makes closing the housing simple and secure. The integrated thumb grip and sculpted shutter button make handling the housing intuitive and comfortable. The NA-TG5 comes with handle brackets and a shutter release extension for users that wish to use the optional handles and trays. Other housing features include 2 fiber optic ports, easy access zoom lever, a 52mm threaded mount for auxiliary lenses, scratch resistant rear window, M10 threaded hole and cold shoe attachment point. TG-6 UNDERWATER-SPECIFIC MODES The TG-6's underwater modes have received a lot of attention from Olympus. There are now underwater-specific macro (think small fish) and microscope modes. There are also now depth-range specific white balances for wide angle. Underwater shallow, mid-range and deep correspond to 0-10' for shallow, 10-50' for mid-range and 50'+ for deep. CMC-1 COMPATIBILITY When using the TG-5 outside of microscope mode, exceptional macro images can still be achieved using the Nauticam CMC-1 magnifying optic which can be used between 28-77mm equivalent focal lengths.

Durch Techniken und Innovationen, die auf jahrelanger Erfahrung beruhen, ist ein einfach zu bedienendes, hochprofessionelles Produkt entstanden. Das Gehäuse für Olympus Tough! TG-5 perfekte Handhabung durch einstellbare Führungsschienen. Einfacher Zugang zu allen wichtigen Kamerasteuerungen durch klar beschriftete, lasergravierte, langlebige Tasten. Die hintere Klappe hat ein großes Fenster für eine gute Sicht auf das Kameradisplay und ist vollständig vom Vorderkörper getrennt, um die Montage der Kamera zu erleichtern. Mit eine Hand Öffnen und Schließen Das Öffnen und Schließen der Olympus TG-5 geht sehr schnell und mühelos vonstatten, dank der seitlichen Schraubenverbindung und der unteren Zentrierstifte. Das Gehäuse steht durch die stabilen und breiten Gummifüße auf der Unterseite sehr stabil. Port und Vorsatzlinsen Das Gehäuse für Olympus TG-5 ist mit einer Hartglasoptik versehen und verfügt über eine M67 und M52 Gewindehalterung, die den Einsatz von zusätzlichem Weitwinkelobjektiv und Makroobjektiv ermöglicht. Licht Die Olympus TG-5 eigene Blitzbeleuchtung wird durch einen Standard-Diffusor im mitgelieferten Schaufenster verbessert. Für eine bessere Leistung bei Weitwinkelobjektiven können ein oder zwei externe Blitzgeräte über eine Glasfaserbuchse angeschlossen werden. Konstruktion und Sicherheit Für die Herstellung unserer Gehäuse werden nur die besten Materialien verwendet, wie z.B. eloxiertes Aluminium, das antikorodal und thermisch beschichtet ist, sowie Edelstahl. Ein langlebiges Produkt, das eine einfache und schnelle Wartung durch den Anwender erfordert. So klein und so reich an Technik! Zwei hochpräzise und hochwertige O-Ring-Dichtungen schützen und gewährleisten eine perfekte und sichere Wasserdichtigkeit für alle beweglichen und / oder abnehmbaren Teile; ein roter Alarm für Feuchtigkeit/Wasser im Inneren des Gehäuses wird durch eine vom Benutzer austauschbare Batterie versorgt. Die Arbeitstiefe beträgt 100 Meter. Eine Öse auf der Unterseite ermöglicht es, das Gehäuse für Olympus TG-5 mit einem Gurt zu sichern. Verschiedene Zubehörteile können mittels einer oberen Schiebeschale und doppelter Gewindebohrungen M6 und einem 1/4 Zoll auf der Unterseite montiert werden. Bedienung EIN/AUS von Olympus TG-5 Ergonomische Kamera-Fokussierung und Auslöser für eine einfache Bedienung mit Handschuhen Modus-Taste Besondere Merkmale Doppel-LWL-Kabeladapter für TG-4/TG-5 (im Lieferumfang enthalten) Alle Olympus TG-5 Hauptsteuerungen Einfaches Öffnen/Schließen mit einer Hand Feuchtigkeitsalarm Doppelte M67 und M52 Gewindehalterung zur Verwendung zusätzlicher Weitwinkel- und/oder Makroobjektive Doppelte hochwertige O-Ring-Dichtungen

The housing for Olympus Tough! TG-6 allows to capitalize on the camera full potential and to capture amazing pictures underwater. Product details An easy to use, highly professional product has been created through techniques and innovations gained from years of experience. The housing for Olympus Tough! TG-6 perfect handling by means of an adjustable strips. Easy access to all key/main camera controls by means of clearly labelled laser-engraved longlasting buttons. The back door has a large window for a fine camera display view and it is entirely detached from the front body to make easier the camera fitting. ONE HAND OPEN/CLOSE It?s very fast to open and close Olympus Tough! TG-6, without any efforts by the user thanks to the side helicoid screw and the bottom centered pins. The housing stands with great stability due to sturdy and wide rubber feet located on the bottom. PORT, CLOSE-UP AND WIDE-ANGLE LENSES The housing for Olympus Tough! TG-6 ends with a tempered glass optic and features a M67 and M52 thread mount that allows the use of additional wide angle lens and macro lens. LIGHTING The Olympus Tough! TG-6 own strobe lighting is enhanced thanks to a standard diffuser placed in the provided flash window. For better performance with wide angle lenses, one or two external strobes can be connected by optic fiber bushing. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such anodized aluminum which is anticorodal and thermo-coated and stainless steel. A longlasting product that requires easy and simple maintenance by the user. So small and so rich in technology! Dual high precision and quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. An hole positioned on the bottom allows to secure the housing for Olympus Tough! TG-6 with a strap. Different accessories can be fitted by means of an upper sliding tray and double threaded M6 holes and one 1/4W on the bottom. Controls ON/OFF of Olympus Tough! TG-6 Ergonomic camera focusing and shutter button for an easy use with gloves Mode button