TTL-Flash Trigger for Canon II-S

The latest Canon APS-C mirrorless camera is finally here!  The Canon EOS R7 utilizes Canon's newest RF mount and boasts a 32.5MP CMOS sensor.  Crop-sensor cameras have always been popular with the underwater shooter community and with good reason. Lens choices, size, and weight are just a few of the great features that shooting APS-C cameras has. The EOS R7 gives original Canon 7D and 7D Mark II shooters a great reason to upgrade and Nauticam is ready to help with the NA-R7 housing.   The Canon EOS R7 Camera The Canon EOS R7 is the latest in Canon's APS-C mirrorless camera lineup which has gained unprecedented demand.  It features the RF lens mount which has the same large 54mm diameter but the ability to have larger rear lens elements that are closer to the sensor gives increased corner and outer edge sharpness.  The R7 uses a 32.5MP CMOS sensor with in-body image stabilization which can reduce shake by up to 7 stops.  The camera's Dual Pixel II autofocus system was carried over from the pro body EOS R3 and features 651 automatic AF points covering the entire sensor area.  It is also capable of recording oversampled 4K 30p video using the full 7K area of the sensor, or subsampled UHD 4K up to 60p from the full sensor width.   The Canon EOS R7 can also use the large EF-mount lens lineup via a simple EF to EOS R adaptor.  The Nauticam NA-R7 housing only supports the the standard EF to EOS R adaptor and does give access to the control ring or drop in filter adaptors.   Key features - Canon EOS R7 32.5MP APS-C CMOS sensor with Dual Pixel AF Up to 30 fps shooting (e-shutter), 15 fps with mechanical In-body image stabilization, rated at up to 7 stops Oversampled UHD 4K up to 30p, line-skipped or cropped 4K/60p 10-bit video as 'PQ' true HDR footage or C-Log 2.36M dot OLED viewfinder 1.62M dot fully-articulating touchscreen Twin UHS-II SD card slot Environmental sealing The Canon EOS R7 underwater housing from Nauticam   The NA-R7 underwater housing follows suit with Nauticam's drive for innovation. Like the full frame Canon EOS R5, R5 C and R3, the NA-R7 present shooters with the ability to use both the available legacy EF lenses via an adapter in addition to their native RF optics.  To support both the legacy and native lenses, Nauticam has designed a N100 to N120 adapter which integrates into the N120 Canon EF port system. Canon's EF to RF mount adapters can be affixed to the camera before insertion into the housing. When using the EOS R7 inside the housing with the adapter and a supported EF lens, the port and extension ring arrangement will be identical to the same setup on a Nauticam Canon N120 DSLR. As the RF-S lens lineup emerges, dedicated port and extension ring combinations will be listed on the new N100 RF-S Port Chart.  Mission Control Nauticam engineers are obsessed with getting the underwater image maker unfettered access to all the necessary controls, with as many within easy reach of the ergonomic rubberized handles. This Mission Control philosophy extends to the NA-R7 where a dual thumb lever is placed by the right front side accessing the M-Fn and Record buttons.  On the rear right side is a thumb lever accessing AF-ON. Near the left handle is a thumb lever for "Playback." Large knurled and rubberized control dials access the camera's "main" and "sub" command dials. The two-stage trigger allows for smooth focus and firing activation. Additional buttons for "Menu", "Focus Point Selection" and others are also easily reached from the handles. Flash triggering Flash triggering is achieved via one of two optional Flash Triggers, a manual LED trigger (NA26305) or a TTL Flash Trigger (NA26321) that use the built-in fiber optic bulkheads with optional fiber-optic cables to trigger supported strobes. For controlling strobes that do not support fiber optic flash triggering, a variety of legacy hot-shoe flash control bulkheads are available. Integrated system for vacuum testing and leak detection The Nauticam vacuum check and leak detection electronics are shipped with the NA-R7 as standard equipment. Combined with an accessory vacuum valve (NA25624) this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

The Canon EOS R6 Mark II may look like it's predecessor, but it offers a lot of new features attractive to underwater image makers. It has a new 24MP full frame sensor, it is capable of recording UHD 4K/60p without any crop factor internally and also supports ProRes RAW recording up to 6K to an external recorder such as the Ninja V. The Canon EOS R6 II Camera The Canon EOS R6 Mark II is one of the latest in Canon's full-frame mirrorless camera lineup which has gained unprecedented demand.  It features the RF lens mount which has the same large 54mm diameter but the ability to have larger rear lens elements that are closer to the sensor gives increased corner and outer edge sharpness.  TThe R6 Mark II uses an all new 24MP CMOS sensor which boosts the resolution from its predecessor and also significantly improves its rolling shutter performance. It offers in-body image stabilization rated at up to 8 stops of correction. The camera's Dual Pixel CMOS AF II autofocus system uses 1053 autofocus points across the entire frame. It is also capable of recording 4K video at up to 60p internally and 6K 60p extern The EOS R6 Mark II can also use the large EF-mount lens lineup via the Canon RF to EOS R Adapter. Key specifications 24.2MP full-frame CMOS sensor UHD 4K shooting up to 60p, 1080 at up to 120p, 6K ProRes RAW recording externally up to 60p 100% coverage Dual Pixel II AF system 12 fps / 40 fps burst (mechanical / electronic shutter) 3.69M-dot OLED EVF 3" 1.62M-dot vari-angle touchscreen LCD 580 shot-per-charge battery rating Dual UHS-II SD Slots The Nauticam Underwater Housing for the Canon EOS R6 Mark II Camera The NA-R6II underwater housing follows suit with Nauticam's drive for innovation and it supports both the Canon EOS R6 and R6 Mark II. A conversion kit is required for the original R6 and will be provided upon request. Like its predecessors, the NA-R6II presents shooters with the ability to use both the available legacy EF lenses via an adapter in addition to their native RF optics. To support both the legacy and native lenses, Nauticam has integrated the NA-R6II into the N120 port system. Canon's EF to RF mount adapters can be affixed to the camera before insertion into the housing. When using the EOS R6 Mark II inside the housing with the adapter and a supported EF lens, the port and extension ring arrangement will be identical to the same setup on a Nauticam Canon N120 DSLR. With the ever growing RF lens lineup, you can also follow the dedicated N120 Canon RF port chart that is being updated and expanded with each new lens release. Please note that the Canon Control Ring and Drop-in Filter EF to EOS R adapters are not accessible within the housing. Mission Control Nauticam engineers are obsessed with getting the underwater image maker unfettered access to all the necessary controls, with as many within easy reach of the ergonomic rubberized handles. This Mission Control philosophy extends to the NA-R6II where a dual thumb lever and sub-lever are placed by the right handle. The dual thumb lever on the front right side activates the "M-Fn" and "Rec" buttons while the sub-lever on the right rear side corresponds to the "AF-ON" button. Near the left handle is a thumb lever for "Playback" for easy image review. Large knurled and rubberized control dials access the camera's "main" and "sub" command dials. The two-stage trigger allows for smooth focus and firing activation. Additional buttons for "Menu", "Focus Point Selection" and others are also easily reached from the handles Flash Triggering Flash triggering is achieved via one of two optional Flash Triggers, a manual LED trigger (NA26301) or a TTL Flash Trigger (NA26321) that use the built-in fiber optic bulkheads with optional fiber-optic cables to trigger supported strobes. For controlling strobes that do not support fiber optic flash triggering, a variety of legacy hot-shoe flash control bulkheads are available. Integrated Vacuum Check and Leak Detection System The Nauticam vacuum check and leak detection electronics are shipped with the NA-R6 as standard equipment. Combined with an accessory vacuum valve (NA25625) this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.