Sale in the name of Klaus Vanderheyden GmbH i.L. The Ikelite Quick Release Handle allows for easy attachment and removal of arm components at the touch of a button for added convenience above and below water. Durable aluminum and ABS construction with soft-touch rubber over-molding for a comfortable grip for large or small hands. Placement of release handle does not interfere with opening and closing the housing. Compatible with Steady Tray for GoPro and Micro Trays. Left-hand and right-hand handles sold individually. Left-hand handle mounts on the left side when viewing the housing and tray from the back. Left and right handles are not interchangeable.

Sale in the name of Klaus Vanderheyden GmbH i.L. The Ikelite Quick Release Handle allows for easy attachment and removal of arm components at the touch of a button for added convenience above and below water. Durable aluminum and ABS construction with soft-touch rubber over-molding for a comfortable grip for large or small hands. Placement of release handle does not interfere with opening and closing the housing. Compatible with Steady Tray for GoPro and Micro Trays. Left-hand and right-hand handles sold individually. Left-hand handle mounts on the left side when viewing the housing and tray from the back. Left and right handles are not interchangeable.

Sale in the name of Klaus Vanderheyden GmbH i.L. This company also handles invoicing. Vacuum valve fitting for older housings without a spare 1/2" diameter accessory port. The valve's low profile avoids interference with control operation. The included waterproof plug is secured to the fitting to prevent accidental loss. Vacuum pump sold separately.

Sale in the name of Klaus Vanderheyden GmbH i.L. This company also handles invoicing. Use to transition between 1/2-inch and 3/4-inch flex arm components. Features male fitting on 1/2-inch end and female fitting on 3/4-inch end.

Sale in the name of Klaus Vanderheyden GmbH i.L. This company also handles invoicing. Mounts to the Ikelite Quick Release Handle for attachment of 3/4 in flex arms. Extended length allows for the attachment for optional accessories like the EV Manual Controller.

Sale in the name of Klaus Vanderheyden GmbH i.L. This company also handles invoicing. Mounts to the Ikelite quick release handle. Compatible with 3/4" flex arm components.

Sale in the name of Klaus Vanderheyden GmbH i.L. This company also handles invoicing. Mounts to the top bracket of an Ikelite DSLR body. Compatible with 3/4" flex arm components.

Sale in the name of Klaus Vanderheyden GmbH i.L. This company also handles invoicing. Attachment for the base plate for GoPro to attach a 3/4 flex arm.

Sale in the name of Klaus Vanderheyden GmbH i.L. This company also handles invoicing. Provides an easy way to attach fibre optic cables to almost any housing. Simply cut to size and attach to the housing in front of the built-in camera flash. Provides two connectors for attaching one or two fibre optic cables.

Sale in the name of Klaus Vanderheyden GmbH i.L. This company also handles invoicing and shipping. Mounts to DS50, DS51, DS125, DS160 or DS161 strobes for attachment to 1" (25mm) diameter ball arms from Ikelite, TLC, Ultralight, Nauticam, and others. Requires a compatible 1" Ball Clamp, sold separately. The 1-inch Ball Arm System Mark II features 1" ball components with a groove and o-ring to prevent slippage for improved holding power with less force. While underwater, clamps may be finger-tightened to keep lighting in place yet allow repositioning without loosening the clamp. All parts are hard coat type III anodized for a long lasting, scratch resistant finish. The replacement screw is sold as product # 0202.4.

Sale in the name of Klaus Vanderheyden GmbH i.L. A rigid anodized aluminum arm with balls at each end to extend your strobe or video light arm. Add an extension and clamp to your existing strobe arm for reduced backscatter and more creative lighting effects when shooting with a wide angle lens. The slotted design allows for the attachment of a lightweight accessory in the middle of the extension. When used with our Sliding Ball Mount, the additional accessory is able to move up and down the length of the arm for quick repositioning during a dive. The 1-inch Ball Arm System Mark II features 1-inch ball components with a groove and o-ring to prevent slippage for improved holding power with less force. While underwater, clamps may be finger-tightened to keep lighting in place yet allow repositioning without loosening the clamp. All parts are hard coat type III anodized for a long lasting, scratch resistant finish.

Sale in the name of Klaus Vanderheyden GmbH i.L. Finds Pit Our finds pit with old treasures - all parts are new and unused. All housings receive a new housing O-ring before delivery. For newcomers who want to take their first steps in underwater photography as inexpensively as possible with the camera they may still have. The discounted prices refer to the last known list price of the product. A full featured and durable waterproof housing for Sony Alpha a7 II, a7R II, and a7S II mirrorless cameras. Suitable for scuba, snorkel, surf, pool, and any application in or around the water. This housing requires the addition of a compatible Four Lock (FL) Lens Port for waterproof operation. Lens Port not included. Full-frame, low-light performance in a packable package. True Sony TTL We would like to introduce an important term that has been missing from all previous discussions about taking the Sony Alpha 7 series underwater: TTL. When your subject is quickly approaching, you'll be glad to have the only housing that provides TTL support for Alpha 7 cameras. An integrated TTL circuit features model-specific encoding, which has been fine-tuned to Sony's latest flash exposure protocol. The circuit is powered by the strobe for zero maintenance and no batteries to change. Exposure compensation in TTL mode is supported using the camera's built-in control. At this time, only Ikelite DS strobes are capable of powering the circuitry. SEA&SEA, INON, and Nikonos strobes will still enjoy fast recycle times and improved battery life, but must be used in manual exposure modes only. A fast and reliable strobe connection is essential to getting the shot underwater. This housing provides a direct electrical connection to the camera's external flash hot shoe. Cord attachment is as easy as screwing in a lightbulb, and the threaded fit prevents accidental detachment during use. The bulkhead connection has been moved to the top of the housing to keep cords out of your way and reduce strain on the cord ends. A variety of sync cord terminations are available for Ikelite, SEA&SEA, INON, or Nikonos strobes for ultimate versatility. The Lens Support You Want It couldn't be faster to change ports than this system—just press the port on and snap the four locks closed. This housing accepts a variety of ports to accommodate all of the most popular zoom, macro, and wide angle lenses from Sony, Canon, Sigma, and more. Our custom optical grade acrylic domes provide the color, clarity, and durability of glass at a fraction of the travel weight. Our new soft touch lobed zoom knob puts a unique system of universal zoom gears right at your fingertips. We provide two zoom sets with each housing, one for use with most popular larger diameter zoom lenses and a second designed for use with smaller diameter zoom lenses. Both sets are lightweight and easy to install with no modification to the lens required. A variety of dome and flat ports attach with four locking latches for maximum security and quick changes between dives. Great Handling A compact mounting tray attaches to the camera's tripod attachment point and slides into the front of the housing simply and securely. The mounting tray features a 1/4-20 tripod mount so that it doesn't need to be removed when you switch to surface photography. Sony created a fantastic control set for this camera series, mimicked in the housing by larger controls and push buttons which are easy to access even with thick gloves. Whenever possible, controls are located in the same configuration as on the camera to replicate the muscle memory and familiarity you've developed with your camera on the surface. Control symbols laser engraved into the back of the housing will never peel off or fade even with years of use. With a system of this caliber, a tray with handle is essential for the attachment of lighting and comfortable handling in a wide variety of shooting scenarios. This housing includes a balanced aluminum tray with our signature quick release handle for easy attachment and removal of strobes and video lights. This unique handle is curved slightly to fit the natural curvature of your hand, and features a soft over-mold which makes it a delight to hold. The complete tray and handle detaches quickly with the removal of two screws for travel. A new modular tray provides a 1/4-20 tripod mount and allows for the attachment of a second right-hand handle to the existing tray. See the O-Ring Seal An o-ring works best when it's true to its original form. Our signature open-groove design suspends the rear o-ring in a natural position that is easier to maintain and more reliable than forcing the o-ring into a channel. For added reassurance, there's no substitute for inspecting the actual o-ring seal through the back of your housing once it is closed. Polycarbonate is fundamentally corrosion-resistant for easy maintenance year after year. We are proud to offer the only housing and lighting system for Sony Alpha a7 series cameras that is 100% designed, built, and tested in the USA. Our housings are handmade and individually inspected for fit, function and waterproof integrity. The average assembly technician is a certified scuba diver and has over 16 years of experience building Ikelite products. We back our products with over 50 years of experience and the most accessible and responsive customer service staff in the dive industry. Compatibility The newer Mark II generation of a7-series cameras are very similar to the the original a7-series cameras, but not interchangeable. Differences in size and lens placement prevent the Sony Alpha a7 Mark I, a7R Mark I, or a7S Mark I cameras from being used in this housing. Please see product # 6843.71.

Sale in the name of Klaus Vanderheyden GmbH i.L. Finds Pit Our finds pit with old treasures - all parts are new and unused. All housings receive a new housing O-ring before delivery. For newcomers who want to take their first steps in underwater photography as inexpensively as possible with the camera they may still have. The discounted prices refer to the last known list price of the product. A fully featured and durable waterproof housing for Olympus Stylus 1s cameras. Suitable for diving, snorkelling, surfing, pool and any use in or near the water. This compact and lightweight housing provides operation of all important camera functions up to depths of 200 feet (60m). The housing controls are placed in a configuration as similar to the camera's layout as possible for the most natural operation taking advantage of the muscle memory you've already developed in surface use. Rear controls are marked with easy-to-see laser engraved symbols which never fade or fall off. The front-loading camera mounting system makes installation and removal a breeze. The camera mounting plate allows ready access to the battery and memory card, and features a standard 1/4-20 mounting point for attachment to a tripod topside. Color correction and external lighting Light is absorbed as it travels through even short distances underwater, making colors appear dull or monochromatic. To preserve the natural colors of your subject, it's important to stay within arm's reach—no more than 3-4 feet (1m) away. Additional color correction and clarity can be obtained by adding a color filter or external light. The lens port of the housing accept our 3-inch diameter color filters. Color filters attach via a press fit and are available for both tropical blue water and green water settings. A color filter reduces the amount of light that reaches the camera's sensor, so they are most effective in sunny conditions at relatively shallow depths up to approximately 80 feet (24m). A flash or constant on light is necessary for close-up, night dives, and deep depths. An external light also brings out more colors in sunny conditions. External lights are typically not used in conjunction with color filters, as the combination will result in tones that are too red or too purple. True TTL exposure An integrated TTL circuit is fine-tuned to the Olympus Stylus 1s flash exposure protocol for the most accurate exposure possible. The circuit is powered by the strobe for zero maintenance and no batteries to change. Exposure compensation in TTL mode is supported using the camera's built-in control. At this time, only Ikelite DS strobes are capable of powering the circuitry. SEA&SEA, INON, and Nikonos strobes will still enjoy fast recycle times and improved battery life, but must be used in manual exposure modes only. This housing provides a direct electrical connection to the camera's external flash hot shoe. Cord attachment is as easy as screwing in a lightbulb, and the threaded fit prevents accidental detachment during use. The bulkhead connection has been moved to the top of the housing to keep cords out of your way and reduce strain on the cord ends. A variety of sync cord terminations are available for Ikelite, SEA&SEA, INON, or Nikonos strobes for ultimate versatility. The camera's built-in flash is suitable for firing an external strobe, but not for lighting a photo underwater. Two fiber optic ports are built into the front of the housing provide an attachment point for fiber optic cords from most major manufacturers. Use of a fiber optic connector requires the camera's built-in flash to fire, reducing battery life and bypassing the TTL functionality of the housing. A bright constant-on video light can be used instead of or in addition to a flash. A constant-on light is not as bright as a strobe flash. Constant-on lights do provide added versatility because they can be used for focus assist and for improved colors when shooting video. Two 1/4-20 threaded mounting points are included on the bottom of the housing for the attachment of a tray and handle system. Handles provide improved ergonomics underwater and are the foundation for your lighting mounts. There is a simple rule that brighter is better underwater. A high-quality lighting system can produce magazine quality results with almost any compact camera system. Wide angle, macro, and color filters The housing provides full access to the camera's zoom range. The design of this camera's lens limits the addition of external wide angle accessories. For wide angle photography, we recommend the WD-3 Wide Angle Dome which restores the camera's true angle of coverage and clarity underwater. Unlike a wet lens, the WD-3 is super sharp edge-to-edge, free of dark shadows in the corners of the image, and lightweight for travel. The WD-3 can be removed and replaced underwater so that you can shoot wide angle and macro on the same dive. The port is threaded for the direct attachment of 67mm threaded accessory macro lenses. We recommend a macro lens which is designed for underwater use like those from Epoque, INON, Subsee, Nauticam, and other manufacturers. 67mm threaded wide angle wet lenses may be attached to the front of the lens port, but will exhibit vignetting (dark shadows around the edges of the image). Vignetting can be reduced by zooming in or cropping the photo in post-production. Durability and corrosion free performance Our brand new ABS-PC blend provides strength and corrosion free performance year with minimal maintenance. The specially formulated color deflects the sun to keep your camera running cooler, longer. Compared to black or clear housings, the light gray color provides superior contrast for enhanced view of the camera, LCD screen, and o-ring seal. The unique rear seal design prevents accidental twisting or stretching of the o-ring for simple and confident assembly. We have eliminated the need for an o-ring groove or channel which can trap sand, dirt, or debris. Two double-passivated stainless steel locking lid snaps are simple to use and virtually unbreakable. The clear back allows you to see the o-ring form a solid, watertight seal as it Closes.

Sale in the name of Klaus Vanderheyden GmbH i.L. A rigid anodized aluminum arm with balls at each end to extend your strobe or video light arm. Add an extension and clamp to your existing strobe arm for reduced backscatter and more creative lighting effects when shooting with a wide angle lens. The slotted design allows for the attachment of a lightweight accessory in the middle of the extension. When used with our Sliding Ball Mount, the additional accessory is able to move up and down the length of the arm for quick repositioning during a dive. The 1-inch Ball Arm System Mark II features 1-inch ball components with a groove and o-ring to prevent slippage for improved holding power with less force. While underwater, clamps may be finger-tightened to keep lighting in place yet allow repositioning without loosening the clamp. All parts are hard coat type III anodized for a long lasting, scratch resistant finish.

Sale in the name of Klaus Vanderheyden GmbH i.L. The Standard Clamp attaches two (2) 1-inch diameter balls. Thicker plates provide the perfect combination of strength and range of motion. Plates are spring-loaded for easy assembly and breakdown of your arm system. A hard anodized aluminum wing nut allows for easy one-handed operation and will withstand years of use. The 1-inch Ball Arm System Mark II features 1-inch ball components with a groove and o-ring to prevent slippage for improved holding power with less force. While underwater, clamps may be finger-tightened to keep lighting in place yet allow repositioning without loosening the clamp. All parts are hard coat type III anodized for a long lasting, scratch resistant finish.

Sale in the name of Klaus Vanderheyden GmbH i.L. The Standard Clamp attaches two (2) 1-inch diameter balls. Thicker plates provide the perfect combination of strength and range of motion. Plates are spring-loaded for easy assembly and breakdown of your arm system. A hard anodized aluminum wing nut allows for easy one-handed operation and will withstand years of use. The 1-inch Ball Arm System Mark II features 1-inch ball components with a groove and o-ring to prevent slippage for improved holding power with less force. While underwater, clamps may be finger-tightened to keep lighting in place yet allow repositioning without loosening the clamp. All parts are hard coat type III anodized for a long lasting, scratch resistant finish.

Sale in the name of Klaus Vanderheyden GmbH i.L. The Accessory Clamp attaches two (2) 1-inch diameter balls. The base plate accepts the Ikelite Auxiliary Ball Mount for the attachment of additional lightweight accessories in the middle of your strobe arm. Perfect for adding a spare modeling light or video light. Plates are spring-loaded for easy assembly and breakdown of your arm system. The 1-inch Ball Arm System Mark II features 1-inch ball components with a groove and o-ring to prevent slippage for improved holding power with less force. While underwater, clamps may be finger-tightened to keep lighting in place yet allow repositioning without loosening the clamp. All parts are hard coat type III anodized for a long lasting, scratch resistant finish.

Sale in the name of Klaus Vanderheyden GmbH i.L. The easiest way to stow your wide angle or macro lens when not in use. Allows for the attachment of 67mm threaded lens to an Ikelite Ball Arm Extension Mark II. The beauty of a "wet lens" is the ability to add and remove in while underwater. This holder provides a convenient method to have your lens right at hand when you need it, and safely secured to your system when you don't. No more stuffing your lens in a BCD pocket! Hard anodized aluminum construction provides strength and corrosion resistant performance. Simply attach the holder to the middle of any Ikelite Ball Arm Extension Mark II, and then thread your lens on. Two Lens Holders may be combined back to back to hold both your wide angle and macro lens on the same arm section. This holder is not compatible with 1/2- or 3/4-inch Flex Arms. If you have an older 1-inch ball arm extension without slot, simply swap it out for a new arm extension and re-use your existing clamps.

Sale in the name of Klaus Vanderheyden GmbH i.L. This company also handles invoicing. Mounts to the Vega Video + Photo Light for attachment to 1-inch diameter ball arms from Ikelite, TLC, Ultralight, Nauticam, and others. Requires a compatible 1-inch Ball Clamp, sold separately. The 1-inch Ball Arm System Mark II features 1-inch ball components with a groove and o-ring to prevent slippage for improved holding power with less force. While underwater, clamps may be finger-tightened to keep lighting in place yet allow repositioning without loosening the clamp. All parts are hard coat type III anodized for a long lasting, scratch resistant finish.

Sale in the name of Klaus Vanderheyden GmbH i.L. This company also handles invoicing and shipping. Mounts to DS50, DS51, DS125, DS160 or DS161 strobes for attachment to 1" (25mm) diameter ball arms from Ikelite, TLC, Ultralight, Nauticam, and others. Requires a compatible 1" Ball Clamp, sold separately. The 1-inch Ball Arm System Mark II features 1" ball components with a groove and o-ring to prevent slippage for improved holding power with less force. While underwater, clamps may be finger-tightened to keep lighting in place yet allow repositioning without loosening the clamp. All parts are hard coat type III anodized for a long lasting, scratch resistant finish. The replacement screw is sold as product # 0202.4.

Sale in the name of Klaus Vanderheyden GmbH i.L. This company also handles invoicing. Housings produced August 2020 and later require the newer Trigger Extension v2. Extends the lever away from the housing and closer to a right-hand handle. For use only with controls featuring a curved lever actuator. This extension brings the shutter button and/or back button focus controls out to the handle assembly for maximum comfort. The extension does not change the orientation of the lever. Orientation of the lever varies per control and housing model.

Sale in the name of Klaus Vanderheyden GmbH i.L. This company also handles invoicing and shipping. Mounts to our Quick Release Handle for attachment of 1-inch diameter ball arms from Ikelite, TLC, Ultralight, Nauticam, and others. Requires a compatible 1-inch Ball Clamp, sold separately. Extended length allows for the attachment of the EV Manual Controller. The 1-inch Ball Arm System Mark II features 1-inch ball components with a groove and o-ring to prevent slippage for improved holding power with less force. While underwater, clamps may be finger-tightened to keep lighting in place yet allow repositioning without loosening the clamp. All parts are hard coat type III anodized for a long lasting, scratch resistant finish.

Sale in the name of Klaus Vanderheyden GmbH i.L. This company also handles invoicing. Mounts to the Auxiliary Ball Clamp for the attachment of additional lightweight accessories in the middle of your strobe arm. Requires the Auxiliary Ball Clamp, sold separately. The 1-inch Ball Arm System Mark II features 1-inch ball components with a groove and o-ring to prevent slippage for improved holding power with less force. While underwater, clamps may be finger-tightened to keep lighting in place yet allow repositioning without loosening the clamp. All parts are hard coat type III anodized for a long lasting, scratch resistant finish.

Sale in the name of Klaus Vanderheyden GmbH i.L. This company also handles invoicing. Mounts directly to either side of the Steady Tray for GoPro for attachment to 1 in diameter ball arms from Ikelite, TLC, Ultralight, Nauticam and others. Requires a compatible 1-inch Ball Clamp, sold separately. Hard coat anodized aluminum for a long lasting, scratch resistant finish.