THE CANON EOS R3 CAMERA The Canon EOS R3 in all respects appears to be the mirrorless sibling of the 1DX Mark III DSLR, clearly aimed at fulfilling many of the same roles while offering some additional capabilities through the use of the electronic viewfinder and the larger RF lens mount.  The full-frame 24.1MP Stacked CMOS sensor, in addition to having incredible low-light performance, can also capture full-width 6K video in both Raw and compressed formats at up to 60fps.  The R3 is paired to Canon's industry leading Dual Pixel AF system with 100% frame coverage and the now revived Eye AF system. DUAL PIXEL AF II Canon's Dual Pixel autofocus system has long been a favorite of underwater users, especially when it comes to tacking subjects.  With the R3, the system adds an additional 'Animal' recognition mode which might make the system even more reliable at following moving subjects.  Frame coverage is 100% with 1053 zones to ensure accurate focus wherever the subject may be. LOW LIGHT PERFORMANCE The ability to increase a camera's ISO with little penalty is of critical importance to underwater shooters for both stills and video as shooting with higher F-stop values delivers sharper corners and higher shutter speeds mean less motion blur.  The higher video frame rates also benefit by allowing the shooter to maintain a 180º shutter while still maintaining adequate aperture values.  When using color correction filters, which can often remove more than a full stop of light, compensation via ISO is not as much of an issue for overall image quality.  Maintaining dynamic range, even at high ISO levels is also important for those shooting still images using natural light or in poor water conditions. ENHANCED CONTROLS The R3 features an additional control wheel located at the upper right rear of the camera which doubles as the mode control.  This wheel can be assigned a variety of functions such as ISO and is adjusted by a dedicated control wheel on the housing within easy reach of the right handle.   VIDEO CAPABILITIES The Canon R3 can capture 6K video at up to 60fps in either Raw or more compressed formats.  The 6K capture uses the full sensor width which means no loss in field-of-view.  12-bit 6K capture is possible in both uncompressed Canon Raw or compressed Raw light formats.  10-bit H.265 is also possible in both the HDR PQ and Canon Log3 gamma curves to maximize dynamic range for post processing while maintaining smaller file sizes than a Raw format.  It's also possible (when using supported cards) to simultaneously record 10-bit 4:2:2 DCI 4K 60p video.  For those looking for higher frame rates, 10-bit 4:2:2 compressed 4K/120fps can also be captured, downsampled from the full sensor width.  A natively sampled 4K S35 crop is also an option, allowing for more magnification or the use of APS-C lenses.  The R3 also outputs a clean 6K signal over HDMI via an HDMI Micro Type D connector.  Direct custom white balance in live view is also now possible, making a critical function for underwater video even easier. STABILIZATION The R3 features 5-axis In Body Image Stabilization (IBIS) which can offer up to 8 stops of correction allowing for even smoother video and less camera movement related blur. LARGE ELECTRONIC VIEWFINDER The R3's EVF is an OLED 5.76M-dot that features an OVF simulation mode which leverages. the large dynamic range of the OLED screen to reproduce a scene the way it would look through an optical viewfinder.  The lower dynamic range of electronic viewfinders has always made them more difficult to use underwater, especially in high contrast or backlit scenes. This function can easily be switched on and off by assigning it to a custom function button.  When using the Electronic Shutter, which has an X-Sync speed of 1/180sec, the EVF delivers true no-blackout shooting up to 30fps.   THE NAUTICAM NA-R3 UNDERWATER HOUSING   The Nauticam NA-R3 professional aluminum underwater housing for the Canon EOS R3 mirrorless full frame camera is a tru hybrid shooting solution, just as the R3 itself.  Nauticam has continuously supported both the Canon pro-level DSLR lineup as well as the growing full-frame RF-mount mirrorless cameras with innovative underwater housings and the new NA-R3 is the combination of all those technologies.  Blending elements of our 1D series housings with those for the R series, the NA-R3 will be the most capable housing for the R3 available. MISSION CONTROL Nauticam engineers design each housing to insure that controls are placed where they are needed most and within easy reach of a natural hand position.  The NA-R3 features large knurled control dials for the main and sub-command dials as well as an additional shoulder dial for the customizable control wheel of the R3.  A fourth control wheel, near the front of the left handle can articulate the ring of the optional EF-to-RF lens adapter when using EF lenses.  There is a dual thumb lever on the right side for Record and AF-ON as well as single levers for M-Fn and Fn2.  A lever on the left side actuates the Pv control which can change between exposure preview and OVF simulation modes on the EVF.  An additional dual thumb lever on the left side is for Playback and Magnification. HDMI 2.0 AND MOUNTING POINTS The R3 can output clean 6K 60p over HDMI and the NA-R3 features a large bore M24 bulkhead to support an HDMI 2.0 connection to an external monitor or recorder.  Mounting the monitor or recorder or other accessories is even easier with 3x 1/4"-20 mounting holes as well as an additional M10 mounting point atop the housing.  Check the resources sidebar for supported monitor/recorder housings and recommended accessories. FLASH TRIGGERING Flash triggering can be accomplished via the two included M14 electronic bulkheads (One is pre-installed in the M24 bulkhead via a removable M26-M14 adapter).  If using fiber-optic triggering, the built-in fiber optic bulkheads can be used with either the optional manual LED or TTL-flash triggers to provide the desired type of strobe power control. PREMIUM PROFESSIONAL OPTICS The NA-R3 is built around the N120 Canon RF-mount Port System which supports a wide array of Canon RF mount lenses with a selection of optical glass and acrylic ports.  With lens-removal controls for both EF and RF mount lenses, the NA-R3 can support both lens mount types without modification to the housing.  The EF-RF lens adapter is accommodated inside the housing which allows for the use of the N120 Canon EF-mount Port System without any additional extension rings.  When switching between an EF and RF lens, the camera must be removed to install or remove the adapter.  The Nauticam lineup of Premium Professional Optics can deliver unparalleled optical quality and expanded creative options. When used with the Canon RF 14-35 F/4 IL USM lens, the WACP-2 creates a stunning 140º field-of-view while maintaining an incredibly natural looking image and excellent corner sharpness.  The SMC-1 delivers 2.3x macro magnification to the RF 100mm macro lens while the SMC-2 delivers 3.3x. VACUUM CHECK AND LEAK DETECTION SYSTEM The housing comes with electronics pre-installed for Nauticam's Vacuum Check and Leak Detection system, requiring only the optional M16 Vacuum Valve (25625). This monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

The new Canon EOS R5 promises a revolution in photography and cinema. By employing new technologies, including artificial intelligence for AF and an image stabilizer that comes with up to 8 stops* of protection against vibration, Canon aims to make users forget what they knew about Mirrorless cameras. 45-megapixel photos at 20 frames per second, 4K/120P full frame video and a choice of ISO 100-51200. This camera promises outstanding photos in any conditions.  With the built-in, always-on Bluetooth Low Energy connection, establishing a fast Wi-Fi connection with a smart device and reviewing your shots already on the way back is a snap.  * 8 stops based on standard CIPA tests with RF 24-105mm F4 L IS USM at a focal length of 105mm. Product details Canon EOS R5 Underwater Housing by Isotta The housing respects all the key points of Isotta's line of housings: one-handed opening, double O-ring seals for greater safety, the use of high quality materials and the made in Italy craftsmanship. The housing was created to follow the lines of the camera, resulting small and manageable, while ensuring complete control of camera functions and absolute freedom in the use of accessories. MAN BEFORE MACHINE! The focus in the study of the housing goes to the diver who decides to use it. The comfort in the use and management of the machine in water is a fixed point, studied in every detail. The handles are ergonomic, adjustable and interchangeable*. if necessary; the housing is compact and lightweight, so you won't tire your arm too much and have an excellent control over stability. All buttons are conveniently reachable from the grip position of the handles ensuring maximum management of the camera with minimum effort. The rear back offers a full view of the camera screen so that you can shoot in live view unobstructed and in comfort and it detaches completely from the front body so that it is easy to insert the camera and perform operations inside the housing. The presence of the viewfinder allows you to take pictures framing in the classic way and to replace it with a magnifier. The closing knob is Single-hand actionable. MORE AND MORE CUSTOMIZABLE! Supplied with only the connections for the optical fiber, the housing has been designed with three M16x1 connections and one M24x1 connection, for total freedom in the choice of the conformation of the equipment. When ordering, you can select your preferred lighting control system choosing between Trigger, Sincro N5 or S6 and your right port system. Through the different combinations between ports and extension rings it is possible to use most of the lenses on the market. Various accessories can be used by means of an M8 hole located at the top of the case and two M6 threaded holes located at the bottom. To make it even more unique, have your name or logo engraved. SAFETY IS IMPORTANT! The locking pins on the back are made of stainless steel and penetrate the shell for added strength and security. The housing is made of aluminum, resistant and anti-corrosion, anodized in the unmistakable red color. The classic double o-ring seal is on all moving and removable parts ensures an optimal watertight seal. The camera is held straight, centered and in place by a mounting plate with a safety catch, which slips nimbly into the housing. NNo risk of sudden infiltration. A red humidity alarm inside the case is powered by a user-replaceable battery and instantly signals an increase in humidity in a critical area. Watertightness is guaranteed up to a maximum depth of 100 meters. Highlights Ergonomic side handles, adjustable (via optional accessory) Two built-in fiber optic connectors Two standard electrical sync cord bulkheads Nikonos N5 or S6 not included Back housing completely detachable from the front housing Tray with lock for an easy fitting of the camera Single-hand closing knob for back housing Three M16x1 port for installation of accessories, e.g. vacuum valves or monitors One M24x1 port for installation of accessories, e.g. monitor Aluminum buttons and knobs and levers marked in the near with symbols identical to those of the machine in use Wide back display viewfinder glass Viewfinder Dual O-Ring seals on all buttons and removable parts Moisture sensor with LED and audible indicator (replaceable battery) Removable port - 120mm bayonet Ports security latch to prevent accidental opening Wide, rubber covered feet for solid footing M8 hole located on upper side of the housing for various accessories such as focus lights Two M6 holes located on housing bottom side for different accessories such as brackets for strobes or tripods External viewfinders can be mounted, INON compatible

THE CANON EOS R5 CAMERA The Canon EOS R5 is the latest in Canon's full-frame mirrorless camera lineup which has gained unprecedented demand.  It features the RF lens mount which has the same large 54mm diameter but the ability to have larger rear lens elements that are closer to the sensor gives increased corner and outer edge sharpness.  The R5 uses an all new 45MP CMOS sensor with in-body image stabilization which can reduce shake by up to 8 stops.  The camera's Dual Pixel autofocus system uses 1053 autofocus points across the entire frame.   It is also capable of recording 8K video at 24p or 30p and 4K at up to 120p.   The EOS R5 can also use the large EF-mount lens lineup via three optional adapters, a simple EF to R adapter, one which supports the customizable control ring and another that features a drop-in filter mount. Key Camera Specifications 45MP full-frame Dual Pixel CMOS sensor 8K Video, with option for RAW or 10-bit 4:2:2 C-log or HDR PQ Up to 4K/120p, or oversampled 4K up to 30p 100% coverage Dual Pixel II AF system 12 fps / 20 fps burst (mechanical / electronic shutter) 5.76M-dot OLED EVF with 120fps max refresh rate 3.2" 2.1M-dot fully articulating touchscreen 10-bit HDR photos in HEIF format 1x CFExpress slot, 1x UHS-II SD slot Weather sealing   THE NAUTICAM NA-R5 UNDERWATER HOUSING FOR THE CANON EOS R CAMERA The NA-R5 underwater housing follows suit with Nauticam's drive for innovation. Both the Canon EOS R5 and EOS R present shooters with the ability to use both the available legacy EF lenses via an adapter in addition to their native RF optics.  To support both the legacy and native lenses, Nauticam has integrated the NA-R5 into the N120 port system. Canon's EF to RF mount adapters can be affixed to the camera before insertion into the housing. When using the EOS R5 inside the housing with the adapter and a supported EF lens, the port and extension ring arrangement will be identical to the same setup on a Nauticam Canon N120 DSLR. As the RF lens lineup emerges, dedicated port and extension ring combinations will be listed on the Port Chart. Two lens release buttons, one for RF and one for EF lenses used with the optional Canon adapter, are located on the front of the housing to make lens removal through the port opening simple. Mission Control Nauticam engineers are obsessed with getting the underwater image maker unfettered access to all the necessary controls, with as many within easy reach of the ergonomic rubberized handles. This Mission Control philosophy extends to the NA-R5 where a dual thumb lever and dual sub-lever are placed by the right handle. The upper thumb lever activates the "AF-On" and the lower the "Q" buttons while the sub-lever corresponds to the "M-Fn" and "Record" buttons. Near the left handle is a thumb lever for "Playback" as well as a dedicated switch to change from using LCD to the EVF. Large knurled and rubberized control dials access the camera's "main" and "sub" command dials. The two-stage trigger allows for smooth focus and firing activation. Additional buttons for "Menu", "Focus Point Selection" and others are also easily reached from the handles. An additional control wheel is located on the left side of the housing and will interface with the control ring on the supported EF to EOS R Mount Adapter with Control Ring using the optional gear (NA19561). Flash Triggering Flash triggering is achieved via one of two optional Flash Triggers, a manual LED trigger (NA26301) or a TTL Flash Trigger (NA26321) that use the built-in fiber optic bulkheads with optional fiber-optic cables to trigger supported strobes. For controlling strobes that do not support fiber optic flash triggering, a variety of legacy hot-shoe flash control bulkheads are available. Integrated vacuum check and leak detection system The Nauticam vacuum check and leak detection electronics are shipped with the NA-R5 as standard equipment. Combined with an accessory vacuum valve this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

With the NA-R50 underwater housing, Nauticam introduces its latest innovation, underlining its commitment to pioneering new products with innovative design. The Canon NA-R50 ProPackage consists of: NA-R50 underwater housing from Nauticam Handle plate with 1-inch ball plugs. Fixing for handle plate outlet extension Vacuum valve with hand pump Large padded carrying bag The Canon EOS R50 camera Many underwater photographers wanted to leave the limited performance of their compact camera systems behind, but were reluctant to give up the compact size advantage and simplicity of this system. Other world travellers wonder if there is a way to downsize their DSLR without giving up too much performance. Nauticam has listened to this growing interest and its industry-leading engineers have responded with the new NA-R50. The brief was clear: to create the most compact and friendly housing possible for Canon's award-winning and remarkably compact EOS R50 mirrorless APS-C camera. The additional challenge was to make the housing as simple and straightforward as Nauticam's legendary compact camera housings, while making it even easier to achieve outstanding image results. The resulting housing represents a whole new category for Nauticam, while retaining its renowned ergonomics and quality. Important camera specifications 24.2-megapixel CMOS sensor (APS-C) 4K movie recording without crop at up to 30 frames per second, oversampled from 6K Dual Pixel CMOS AF II Movie für close-up demo mode Electronic first curtain (12 fps) and electronic shutter (15 fps) for continuous shooting Advanced A+ Assist with expanded range of auto-compatible scenes. Longer than 30 minutes of video recording UVC/UAC compatibility for webcams and streaming The Nauticam underwater housing for the Canon EOS R50 Nauticam has always been at the forefront of underwater gear technology. They üre always pushing the boundaries to develop evolutionary and sometimes revolutionary products that make image making easier. The NA-R50 underwater camera is no exception. It combines everything that makes the Nauticam range of housings a favourite among underwater photographers in a small and lightweight design. The new, innovative system allows you to capture images with ease. The new innovative system has been designed around the Canon RF-S 18-45 F4.5-6.3 IS STM lens, as this lens is by far the most versatile and practical RF lens that can be used underwater with the Canon RF APS-C format. The mount is therefore integrated into the housing and requires no additional maintenance, similar to the Nauticam compact camera systems. This lens delivers excellent results in wide to narrow fish portraits, but can easily be combined with Nauticam's excellent WWL-1 or WWL-C to achieve exceptionally sharp wide-angle coverage with full zoom, while maintaining the modest form factor. Nauticam's Compact Macro Converter with water contact optics can be added for a complete system that does it all and can be taken anywhere, fitting easily into a traveller's hand luggage. Made from sturdy aluminium, the NA-R50 body is not only lighter but also more compact than any previous Canon APS-C system. It is the perfect choice for photographers who want to capture stunning images and video with the industry's best autofocus, while enjoying the convenience of minimal bulk and maintenance. The housing comes ready to dive, as even the zoom accessory is included. Add the R50 camera and the RFS 18-45 and you are ready to shoot. Compact and versatile The dimensions of the NA-R50 underwater camera are so small that it can be handheld without a mount for maximum freedom when needed. It measures only 238 mm in width, 150 mm in height and 115 mm in depth. Compared to earlier APS-C camera bodies, the NA-R50 has an incredibly small footprint, which makes it appealing and travel-friendly. Which attachment lens to combine with the NA-R50? Nauticam has become justly famous for its pioneering underwater optical designs. These optics are a particular passion of Nauticam founder and managing director Edward Lai, and the various options offer exceptional performance with the NA-R50 underwater system. The magic of wet lenses lies in their enormous versatility, coupled with outstanding underwater performance. Both macro and super wide-angle interchangeable lenses can be available to the underwater photographer on the same dive. Below you will find a selection of the recommended options. The WWL-1Bis a wide-angle converter that is an excellent match for the Canon RF-S 18-45 F4.5-6.3 IS STM lens. The WWL-1B offers a razor-sharp 130-degree diagonal field of view at 18mm and allows full zoom up to 60 degrees at 45mm. Focusing down to the glass is possible at all focal lengths and provides an amazing wide-angle capability at close range. The all-glass WWL-1B lens offers a sharper overall performance than any wide-angle lens behind a dome on a conventional system. For those who want an even smaller wide-angle option without sacrificing quality, Nauticam offers the WWL-C, a compact all-glass lens that is just as sharp as the WWL-1B but offers a zoom range of 116 degrees at 18mm to about 52 degrees at 45mm. Of course, it also focuses on the front optics. Macro lovers also have a choice. Nauticam recommends the lightweight CMC-1. and CMC-2 lenses for the highest image quality and better autofocus performance. Maximum magnification is achieved at a focal length of 45 mm. The CMC-1 offers more magnification, but is a little more demanding. The CMC-2 still offers a strong 0.6x magnification, but is a little more tolerant.   Flash release The NA-R50 underwater housing uses the pop-up flash of the Canon EOS R50 to provide seamless integration with fibre-optic flashes. Flashes that offer sTTL capability with fibre optics offer the possibility of full TTL compatibility with the R50. Integrated vacuum test and leak detection system The Nauticam vacuum inspection and leak detection electronics are supplied as standard with the NA-R50. Combined with the included M16 vacuum valve, this monitoring system provides constant, up-to-date information on the watertight and submersible condition of the housing. A simple colour-coded LED light system indicates to the user that the vacuum is stable or that the case is losing vacuum. Leak detection is integrated into the same circuitry so that an audible and visual signal is emitted when water is ingressing. The Nauticam system is temperature compensated, so false alarms due to changes in external temperature or camera heating during an action-packed dive are avoided.

Many underwater imaging enthusiasts have been anxious to move beyond the limited performance of their compact camera systems but have been reluctant to give up the compact form factor and simplicity of the genre. Other world travelers have started wondering if there is a way to downsize from their DSLR without giving up too much performance. Nauticam has been listening to this increasing interest and their industry leading engineers have responded with the new NA-R50. The mission statement was clear: Design the most compact and friendly housing possible for Canon’s awarding-winning and remarkably compact EOS R50 mirrorless APS-C camera. The added challenge was making the housing just as simple and straight forward as Nauticam’s legendary compact camera housings, while making it even easier to achieve superior imaging results. The resulting housing represents an entirely new category for Nauticam while maintaining their famous ergonomics and Quality. NAUTICAM NA-R50 UNDERWATER HOUSING FOR THE CANON EOS R50 CAMERA Nauticam has always been at the forefront of underwater housing technology. They consistently push the boundaries to create evolutionary, and sometimes revolutionary, products to make imaging creation easier. The NA-R50 Underwater housing is no exception, integrating everything that makes Nauticam's range of housings a favorite among underwater photographers into a small and lightweight package. The new innovative system is engineered around the Canon RF-S 18-45 F4.5-6.3 IS STM Lens, since this is by far the most versatile and practical RF lens to use on the Canon RF APS-C format underwater. The port is thus integral to housing and requires no additional maintenance, much like Nauticam’s compact camera systems. This lens provides excellent results in the wide to narrow fish portrait FOV range but is easily married to Nauticam’s superb WWL-1 or WWL-C for exceptionally sharp wide angle coverage with full zoom through while still keeping a modest form factor. Nauticam’s Compact Macro Converter water contact optics can be added for a full “do anything and go anywhere” system that easily fits in a traveler's carry on. Constructed from rugged aluminum, the NA-R50 housing is not only lighter but also more compact than any previous Canon APS-C system. It's the perfect choice for photographers who want to capture stunning images and videos with best-in-the-industry auto focus, while enjoying the convenience of minimal bulk and maintenance. The housing comes ready to submerge as even the zoom gear is included. Add the R50 camera and RFS 18-45 and you are ready to shoot. COMPACT AND VERSATILE The NA-R50 underwater housing dimensions are small enough to hand hold without a tray for ultimate freedom if it is required. Measuring just 238mm (9.3in) wide, 150mm (5.9in) in height and 115mm (4.5) in depth. The NA-R50 has an incredibly small footprint compared to previous APS-C camera housings, making it extremely apealing and travel-friendly. WHICH WET LENSES SHOULD I PAIR WITH THE NA-R50? Nauticam has become justifiably famous for their groundbreaking optical designs for underwater. These optics have been a particular passion of Nauticam founder and Managing Director Edward Lai, and several options offer exceptional performance with the NA-R50 underwater system. The magic of the wet lenses is their tremendous versatility, paired with outstanding in-water performance. Both macro and super wide angle interchangeable optics can be available to the underwater photographer on the same dive. A sampling of recommended options are below. The WWL-1B is a wide angle conversion lens that is an excellent match with the Canon  RF-S 18-45 F4.5-6.3 IS STM Lens. The WWL-1B provides a crispy 130 degree diagonal field of view with the lens at 18mm and allows for full zoom through to about 60 degrees at 45mm. Focus down-to-the-glass performance is available at all focal lengths for amazing close focus wide angle capability. The all glass WWL-1B lens provides sharper over-all performance then any wide angle lens behind a dome on a typical system. For those wishing for an even smaller wide angle option without any loss of quality, Nauticam's WWL-C provides a compact all glass optic every bit as sharp as the WWL-1B, but with a zoom range offering 116 degrees at 18mm zooming to about 52 degrees at 45mm. Of course, it also focuses to the front optic.  Macro aficionados have options as well. Nauticam strongly recommends the lightweight CMC-1 & CMC-2 lenses for ultimate image quality and better auto-focus performance. Maximum magnification is achieved at a focal length of 45mm. The CMC-1 offers more magnification but is a bit more challenging. CMC-2 still offers a hefty 0.6X magnification but is a bit more forgiving. FLASH TRIGGERING With the NA-R50 underwater housing, flash triggering is accomplished by utilizing the Canon EOS R50’s pop-up flash making adding strobes that employ fiber optic connections a seamless integration. Strobes that provide STTL capability with fiber optics will provide the option of full TTL compatibility with the R50. INTEGRATED VACUUM CHECK AND LEAK DETECTION SYSTEM The Nauticam vacuum check and leak detection electronics are shipped with the NA-R50 as standard equipment. Combined with an accessory M16 vacuum valve (25625) this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

The latest Canon APS-C mirrorless camera is finally here!  The Canon EOS R7 utilizes Canon's newest RF mount and boasts a 32.5MP CMOS sensor.  Crop-sensor cameras have always been popular with the underwater shooter community and with good reason. Lens choices, size, and weight are just a few of the great features that shooting APS-C cameras has. The EOS R7 gives original Canon 7D and 7D Mark II shooters a great reason to upgrade and Nauticam is ready to help with the NA-R7 housing.   The Canon EOS R7 Camera The Canon EOS R7 is the latest in Canon's APS-C mirrorless camera lineup which has gained unprecedented demand.  It features the RF lens mount which has the same large 54mm diameter but the ability to have larger rear lens elements that are closer to the sensor gives increased corner and outer edge sharpness.  The R7 uses a 32.5MP CMOS sensor with in-body image stabilization which can reduce shake by up to 7 stops.  The camera's Dual Pixel II autofocus system was carried over from the pro body EOS R3 and features 651 automatic AF points covering the entire sensor area.  It is also capable of recording oversampled 4K 30p video using the full 7K area of the sensor, or subsampled UHD 4K up to 60p from the full sensor width.   The Canon EOS R7 can also use the large EF-mount lens lineup via a simple EF to EOS R adaptor.  The Nauticam NA-R7 housing only supports the the standard EF to EOS R adaptor and does give access to the control ring or drop in filter adaptors.   Key features - Canon EOS R7 32.5MP APS-C CMOS sensor with Dual Pixel AF Up to 30 fps shooting (e-shutter), 15 fps with mechanical In-body image stabilization, rated at up to 7 stops Oversampled UHD 4K up to 30p, line-skipped or cropped 4K/60p 10-bit video as 'PQ' true HDR footage or C-Log 2.36M dot OLED viewfinder 1.62M dot fully-articulating touchscreen Twin UHS-II SD card slot Environmental sealing The Canon EOS R7 underwater housing from Nauticam   The NA-R7 underwater housing follows suit with Nauticam's drive for innovation. Like the full frame Canon EOS R5, R5 C and R3, the NA-R7 present shooters with the ability to use both the available legacy EF lenses via an adapter in addition to their native RF optics.  To support both the legacy and native lenses, Nauticam has designed a N100 to N120 adapter which integrates into the N120 Canon EF port system. Canon's EF to RF mount adapters can be affixed to the camera before insertion into the housing. When using the EOS R7 inside the housing with the adapter and a supported EF lens, the port and extension ring arrangement will be identical to the same setup on a Nauticam Canon N120 DSLR. As the RF-S lens lineup emerges, dedicated port and extension ring combinations will be listed on the new N100 RF-S Port Chart.  Mission Control Nauticam engineers are obsessed with getting the underwater image maker unfettered access to all the necessary controls, with as many within easy reach of the ergonomic rubberized handles. This Mission Control philosophy extends to the NA-R7 where a dual thumb lever is placed by the right front side accessing the M-Fn and Record buttons.  On the rear right side is a thumb lever accessing AF-ON. Near the left handle is a thumb lever for "Playback." Large knurled and rubberized control dials access the camera's "main" and "sub" command dials. The two-stage trigger allows for smooth focus and firing activation. Additional buttons for "Menu", "Focus Point Selection" and others are also easily reached from the handles. Flash triggering Flash triggering is achieved via one of two optional Flash Triggers, a manual LED trigger (NA26305) or a TTL Flash Trigger (NA26321) that use the built-in fiber optic bulkheads with optional fiber-optic cables to trigger supported strobes. For controlling strobes that do not support fiber optic flash triggering, a variety of legacy hot-shoe flash control bulkheads are available. Integrated system for vacuum testing and leak detection The Nauticam vacuum check and leak detection electronics are shipped with the NA-R7 as standard equipment. Combined with an accessory vacuum valve (NA25624) this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

THE OLYMPUS OM-D E-M5 MARK III CAMERA Weighing in at under one pound, the E-M5 Mark III packs an outsized punch. The E-M5 Mark III is built around the same 20Mp Live MOS sensor and Dual F.A.S.T Autofocus system as the larger OM-D E-M1 Mark II. New for the Mark III is the addition of a 121-point hybrid AF system which, combined with the powerful TruePic VIII processor allows for 10fps burst mode capture with AF-C. The Mark III's EVF has been upgraded to an OLED display with 60fps refresh rate. The 5-axis in-body stabilization also receives an 0.5 stop bump to 5.5EV. The E-M5 Mark III also steps up in the video category with DCI 4K at 24p or stabilized UHD 4K at 30p using the full width of the sensor to maintain field-of-view. HDMI output supports the 1.4 standard with 8-bit 4:2:2 at up to 30p quality. Key Camera Specs 20MP Live MOS Four Thirds Sensor 121-point Hybrid AF System 10 fps burst shooting with AF-C DCI 4K/24p and UHD 4K/30p video HDMI Output 5.5EV of image stabilization (CIPA-rating) 2.36M-dot OLED EVF With the OM-D E-M5 Mark III, Olympus brings a host of features from their flagship Four Thirds models into an economical and compact package that is ideal for the traveling image maker. THE NAUTICAM NA-EM5III UNDERWATER HOUSING The OM-D E-M5 Mark III places the power of the E-M1 Mark II in a compact travel-friendly package and so does the NA-EM5III. Building on our strong lineup of mirrorless camera housings, the NA-EM5III is a feature-rich underwater imaging tool. Our Mission Control design philosophy insures that critical controls are clearly labeled and easy to access with intuitive placement. The NA-EM5III is built around the extensive N85 port system. Optimized port solutions for a wide variety of Micro Four Thirds lenses and access to our Underwater Corrective Optics makes the Nauticam NA-EM5III a superior image-making platform. Stainless steel stiffening brackets and a shutter release extension, which are compatible with the optional Easitray II or Flexitray II tray systems are included with the NA-EM5III. An M10 threaded accessory mounting point is also ready to accept the optional M10 strobe mounting ball for additional accessory mounting flexibility. HDMI CONNECTIVITY A forward M16 bulkhead can be used for the optional HDMI 1.4 Bulkhead for use with external monitor housings such as the NA-502 or NA-502B for the SmallHD 502 and 502 Bright monitors. See sidebar for recommended configurations. VIEWFINDER OPTIONS The E-M5 mark III has an upgraded OLED Electronic Viewfinder. A clear view for fine focus and composition is critical for successful underwater photography, and nothing beats a magnifying viewfinder. These viewfinders use distance, not closeup vision, and provide a large, clear view of the high resolution Olympus electronic viewfinder. Available in Angled 45º (PN 32205) and Straight 180º (PN 32204) formats, both viewfinders have external dioptric adjustments for dialing in perfect correction matched to the photographer’s eyesight. RAPID FIRE OPTICAL FLASH TRIGGERING The E-M5 Mark III camera with the included FL-LM3 flash is limited to 2-3 fps continuous shooting, even when a low manual power is selected in the camera flash menu. In situations where continuous optical shooting is required, Nauticam’s Mini Flash Trigger for Olympus (26306) can trigger external strobes over fiber optic at up to 10 frames per second! The trigger is powered by onboard coin style lithium batteries, with thousands of flashes available from a set. The NA-EM5III comes fiber optic ready and accepts standard Sea & Sea style bushing connections. Nauticam Universal Fiber Optic cables provide exceptional light transmission for accurate TTL performance. Electrical triggering of legacy wired strobe systems is possible via an electrical Nikonos style bulkhead (optional). INTEGRATED VACUUM CHECK AND LEAK DETECTION SYSTEM The Nauticam vacuum check and leak detection system is available with NA-EM5III as standard equipment. Combined with an optional vacuum valve (NA25624 or NA25625), this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur.

The housing for Olympus OM-D E-M5 Mark II allows to capitalize on the camera full potential and to capture amazing pictures underwater. Product details An easy to use highly professional product has been created through techniques and innovations gained from years of experience. Easy access to all key/main camera controls, even with gloves, by means of clearly labelled lasered long life buttons. The back door has a large window glass for a fine camera display and optical viewfinder view and it is entirely detached from the front body to make easier the camera fitting. The housing stands with great stability due to sturdy and wide rubber feet located on the bottom. ONE HAND OPEN/CLOSE It's very easy to open and close Olympus OM-D E-M5 Mark II, without efforts by the user thanks to the upper helicoid and the bottom centered pins; the camera is placed easily into the housing on a sliding tray that keeps the camera robustly in place. PORTS AND EXTENSION RING A series of ports and extension rings are available in dedicated section. The removable port is fitted thanks to markers and a bayonet 102mm connection to the Olympus OM-D E-M5 Mark II housing. The interchangeable port bodies and extensions rings combine to allow the use of most of lenses on the market for maximum versatility and performance.  LIGHTING Two fiber optic connections are placed in front of the built-in flash and allow the use of external strobe. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such as anodized aluminum, which is anticorodal and thermo-coated, and stainless steel. A longlasting product that requires easy and simple maintenance by the user. Dual high precision and quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. Different accessories can be fitted by means of an M8 upper threaded hole, using the Isotta top handle or via the M6 and M8 threaded holes on the bottom. Controls ON/OFF of Olympus OM-D E-M5 Mark II; Own camera strobe open/close; Ergonomic camera focusing and shutter button for an easy use with gloves; Lens release; Rear control panel; Upper control panel;  All controls are available on the housing;

Compared to the previous OM-D E-M1, and all other Olympus Micro Four Thirds cameras, the E-M1 II is an improvement in every way. The new 20MP Live MOS sensor provides a useful bump in resolution. Dual quad core processors combine to allow 60 fps burst shooting (18 fps with autofocus). An incredibly advanced autofocus system (121 focus points covering 75-80% of the frame) grabs subjects instantly without hunting, and doesn’t let go when tracking. THE OLYMPUS OM-D EM1 MARK II It takes more than just headline grabbing specs on paper to make a great underwater camera system, and the E-M1 Mark II does many of the less obvious things right. The “2×2” dial and button structure doubles the functionality of the control dials and assignable push buttons. Typically these dials control shutter speed and aperture when shooting in manual mode, but with a flick of the 2×2 lever they are reassigned to other parameters (like ISO and Exposure Compensation, as an example). The control dials provide the easiest way to access frequently used camera settings directly, and Olympus has doubled their usefulness! It seems to be a trend among camera makers to sacrifice battery life and handling in an effort to to reduce overall size. Olympus didn’t make this mistake with E-M1 Mark II. The substantial hand grip provides exceptional handling, even with larger lenses, and makes space to accommodate a large battery that offers an exceptional 440 shots per charge (based on the CIPA rating, and many more are likely in real world use). Also new, and notable, is a high bitrate UHD (4K) video recording mode coupled with very capable image stabilization. The camera offers HDMI output to an external monitor, providing an upgraded display for framing, exposure check, and focus confirmation. KEY CAMERA SPECIFICATIONS 20MP Live MOS sensor 5-axis in-body image stabilization system 121-pt hybrid AF system 60 fps burst shooting (18 fps with continuous AF, 10 fps with flash) Fully articulating 3? LCD display High-res electronic viewfinder Cinema (DCI) and UHD 4K video 50MP High-Res Shot mode Weather-sealed body USB 3 (Type-C) THE NA-EM1II UNDERWATER HOUSING BY NAUTICAM A camera of this caliber deserves an exceptional underwater housing. Five and a half years ago, Nauticam entered the Micro Four Thirds underwater housing segment. 17 housing models later, Nauticam is proud to have produced more mirrorless underwater camera housings than any other manufacturer. The Nauticam NA-EM1II isn’t a new design, it is a refinement of the housings that have come previously. The system is field tested, and underwater photographer approved. The housing is small, but not at the expense of functionality or ergonomics. Integrated handles provide a sturdy and comfortable base to operate the system from. An ergonomic shutter release lever, thumb lever for AE-L / AF-L, and well placed control dials provide the same operational feel as any Nauticam DSLR housing. Control buttons are placed within easy reach of the handles, with sufficient spacing to allow easy operation, even by feel. The ergonomic experience of this system is clearly influenced by Nauticam DSLR systems, with class leading control access and feel. More than just good looking, this is a rugged housing, ready to tackle thousands of hours of underwater abuse. Crafted from solid aircraft aluminum, the housing can reach depths of 100m with ease. The secure single rotating housing latch opens the housing back. The camera drops in easily. The rear mounted housing o-ring makes maintenance simple. Dual fiber optic synch ports are standard and take advantage of the camera included FL-LM3 flash for strobe triggering. To make the most of the E-M1 Mark II’s excellent electronic view finder (EVF), Nauticam allows for installation of the acclaimed 45º and 180º magnified viewfinders, providing the ultimate in composition and focus ability. The NA-EM1II is a professional grade underwater housing, supporting the pro-level E-M1 II camera body to its full potential. PREMIUM PROFESSIONAL OPTICS It’s all about the glass, and lenses are the key to terrific photography. This has always been a strength of Olympus systems, and the lineup is now stronger than ever thanks to the Nauticam Wet Wide Lens (WWL-1). WWL-1, paired with an Olympus 14-42mm f/3.5-5.6 EZ Lens or ED 12-50mm F3.5-6.3 EZ*, provides a full zoom through ultra wide angle field of view. In our tests, this combination exceeds the corner sharpness and clarity of even very good micro four thirds wide angle lenses behind dome ports. WWL-1 will focus on its front element for unmatched close focus wide angle performance, and full zoom through means you can zoom to crop in camera for tighter framing. WWL-1 is mounted via a quick change bayonet system that allows fast and easy one handed mounting and removal. An optional lens caddy provides a place to park the WWL-1 lens when not in use. For closeup and macro work, the Nauticam Compact Macro Converter (CMC-1, PN 81301) allows images smaller than 1? wide to be captured. Ultra wide, mid-range and macro imaging capability, all on the same dive! There are many more options for the underwater photographer, including any of the several 14-42mm options, the Panasonic Lumix G X VARIO 12-35mm F2.8 ASPH. POWER O.I.S., Olympus M.ZUIKO DIGITAL ED 12-40mm f/2.8 PRO, Panasonic Lumix G Vario 12-32mm f/3.5-5.6 ASPH, Panasonic Lumix G 14mm F2.5 ASPH, and the Leica DG Macro Elmarit 45mm F2.8 ASPH. *12-50 is usable with WWL-1 from approximately 15.5mm – 50mm with WWL-1. VIEWFINDER OPTIONS  A clear view for fine focus and composition is critical for successful underwater photography, and nothing beats a magnifying viewfinder. These viewfinders use distance, not closeup vision, and provide a large, clear view of the high resolution Olympus electronic viewfinder. Available in Angled 45º (PN 32205) and Straight 180º (PN 32204) formats, both viewfinders have external dioptric adjustments for dialing in perfect correction matched to the photographer’s eyesight. INTEGRATED VACUUM CHECK AND LEAK DETECTION SYSTEM The Nauticam vacuum check and leak detection system is available with NA-EM1II as standard equipment. Combined with an optional vacuum valve (PN 25624), this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. FLASH CONNECTORS FOR OPTICAL TTL Reliable automatic flash exposure is available with the NA-EM1II and a variety of optically fired flashes. The Inon Z-240, D-2000, S-2000, and Sea & Sea YS-D1/YS-D2 strobes provide automated lighting, precisely reproducing the camera’s FL-LM3 flash at a proportionally greater intensity. This system yields accurate automatic TTL flash performance – even in manual exposure mode – with no electrical sync cables to flood! The NA-EM1II comes fiber optic ready and accepts standard Sea & Sea style bushing connections. Nauticam Fiber Optic cables, available for both Inon and Sea & Sea strobes, provide exceptional light transmission for accurate TTL Performance. RAPID FIRE OPTICAL TRIGGERING The E-M1 Mark II camera with FL-LM3 flash is limited to 2-3 fps continuous shooting, even when a low manual power is selected in the camera flash menu. In situations where continuous optical shooting is required, Nauticam’s Mini Flash Trigger (26306) can trigger external strobes over fiber optic at up to 10 frames per second! The trigger is powered by onboard coin style lithium batteries, with thousands of flashes available from a set. Electrical triggering of legacy wired strobe systems is possible via an electrical Nikonos style bulkhead (optional).

Introducing the Nauticam NA-S5II underwater housing, a robust and ergonomic solution designed to accommodate the Panasonic Lumix S5 II and S5 IIX for underwater photography and videography. This housing provides unfettered access to all camera controls and functions, enabling users to fully utilize the camera's capabilities while diving. Its durable construction and user-friendly features make it an ideal choice for underwater storytellers seeking a dependable and efficient underwater housing Option. THE PANASONIC LUMIX S5II(X) CAMERA Panasonic has a knack for developing cameras that often fill a unique niche that have earned the brand a passionate following around the globe. So where does the S5II slot for the underwater enthusiast? First and foremost, this camera provides a remarkable value for a full frame, feature rich platform in a compact (for full frame) body. Despite its entry level pricing, it punches well above its weight class with some impressive specifications. Here is what stands out. Dual Native ISO The S5II is already a great low light performer with a 24mp Full Frame sensor, but with Dual Native ISO, a shooter can jump to the higher native ISO with less grain than what would be typical. State of the Art Image Stabilization Yes, many cameras sport IBIS these days, but Panasonic is in a different league. Hand held video is mind-bendingly smooth.  Built-In Cooling Fan Many recent top-of-the-line cameras from other manufacturers have had the video performance hobbled by overheating. But Panasonic has always prioritized video performance and has included built-in cooling. The result? Unlimited 4K internal recording times in 10-bit and 30-minute record for 6K 30p on either camera. Much Improved Phase Detection AF Not always a Panasonic strong point, the S5II makes huge strides in AF performance. Perks for the S5IIX The "X" offers even more video goodness. HDMI ProRes RAW or ProRes 422 output for external recording. For topside recording, the camera offers direct to SSD recording via USBC at bit-rates up to 800Mbs. Panasonic Lumix S5II Specifications FF 24.2MP Sensor w/o LPF 96MP (JPEG, RAW) Dual Native ISO (AUTO, LOW, HIGH) ISO100-51200 (Ex50-204800) 5-axis,5-stop (*1)+Active I.S. 6.5-stop (*2) Phase Hybrid AF, 779-point EV -6 - 18 Photo: 1/8,000-60, Bulb Video: 1/16,000-1/2 X=1/250 Panasonic Lumix S5IIX Specifications FF 24.2MP Sensor w/o LPF 96MP (JPEG, RAW) Dual Native ISO (AUTO, LOW, HIGH) ISO100-51200 (Ex50-204800) 5-axis,5-stop (*1)+Active I.S. 6.5-stop (*2) Phase Hybrid AF, 779-point EV -6 - 18 Photo: 1/8,000-60, Bulb Video: 1/16,000-1/2 X=1/250 C4K, 4K, 3.3K - 800Mbps (USB-SSD), 600, 400Mbps FHD 200Mbps 5.8K/C4K/3.3K (USB-SSD), FHD THE NAUTICAM NA-S5II UNDERWATER HOUSING Nauticam’s tagline is “Innovation Underwater”, and the company is dedicated to following through with that promise in the industry, while helping to protect customer investments in existing Nauticam gear whenever possible. The NA-S5II/X is a prime example as this underwater housing is designed to work flawlessly with the Panasonic Lumix S5II and the S5X. This NA-S5II allows completely unrestricted access to all of the camera's controls, positioning critical controls like AF-ON directly at the photographer's finger tips.   The NA-S5II underwater housing features the rotary housing lock which is now standard on their more compact line of mirrorless camera housings. With this feature, you can easily open and close the housing with one hand.  Mission Control Nauticam engineers are obsessed with usability and the Mission Control philosophy means placing essential controls where they are needed, unrestricted by where they are located on the camera body. Placing the controls as close to the handles as possible and within easy and natural reach, the user can focus on composition and timing their shot while adjusting exposure or focus without taking their eye off the EVF or LCD. The NA-S5II has a thumb lever on the right rear side of the housing that comfortably accesses AF-On without ever letting go of the handle. An additional lever on the rear of the NA-S5II allows for focus mode switching between C/S/MF, while a multi-directional pad gives the ability to navigate the menu or move the focus points. EF and L Lens Support Sigma's MC-21 EF to L adapter allows for the use of Canon and Sigma EF-mount lenses to be used with the S5II/X camera. The NA-S5II Housing is designed to not only accommodate the adapter but to allow for the use of the existing focus and zoom gears for Canon EF-mount lenses for the N120 Canon System along with the existing Canon N120 extension ring and port combinations for those lenses.  As more native L-mount lenses become available, those best suited to underwater use will be added to the system.  For full compatibility, you can refer to the port chart found here.   Flash Triggering For rapid-fire manual flash triggering, the NA-S5II is compatible with the Mini Flash Trigger (NA26305) which uses small LEDs to trigger external flashes via Nauticam Universal Fiber Optic Cables (NA26216). The Panasonic DMW-FL70 flash is not supported within the housing. Vacuum Check and Leak Detection System The Nauticam vacuum check and leak detection electronics are shipped with the NA-S5II as standard equipment. Combined with an optional accessory M14 vacuum valve (NA25624) this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

Sony's line of APS-C mirrorless cameras has long offered top-level specs at an economical price point along with access to an extensive line of interchangeable lenses. For the A6400, Sony has paired the high-resolution 24mp sensor from the A6300 with a new Bionz X processor that borrows technology from the flagship A9. The A6400 can also shoot 4K video downsampled from the full sensor area without the recording time limit of the A6300 and A6500. Improved autofocus and faster camera response make this Sony mirrorless a standout in the APS-C mirrorless camera field. THE SONY A6400 CAMERA Mirrorless cameras have long led the way in hybrid cameras that allow for high-quality still and video recording from a compact interchangeable lens package. The APS-C sensor of the A6400 delivers both 24.2MP still raw images at up to 11fps continuous shooting as well as oversampled 4K video from the full-sensor width recorded in high dynamic range HLG and S-log gamma curves. The A6400 is highly customizable which is made easier by the upgraded menu system. Boot-up time and overall responsiveness of the camera are also improved thanks to the new Bionz X processor. The most notable upgrade to the A6400 is found in the autofocus system. Sony's Real-time Tracking makes using tracking-based autofocus easier. With the A6500 and the A6300 the user would have to decide on subject matter beforehand, switching between Eye-AF where the camera detects and follows a human eye, face detection or simple tracking of an object. With Real-time Tracking, the object that lies in the selected area of the frame will be tracked, regardless of what it is. This is notable for the underwater user that also uses the camera for topside imagery as it eliminates having to reconfigure the autofocus for tracking underwater subjects. For the video shooters, 4K capture at up to 30p is downsampled from the full-width of the sensor (6K). Recording time restrictions have been removed and the use of HLG and S-Log gamma curves is now an option to maximize dynamic range of the footage. Key Camera Specs 24MP APS-C sensor 425-pt phase detection AF system with Real-Time Tracking 2.36M-dot electronic viewfinder New Bionz X processor ISO range from 100-32000 11fps burst shooting 4K/30p video capture with HLG and S-Log THE NA-A6400 UNDERWATER HOUSING Nauticam has created housings for the original A6000, the A6300, A6500 and now the A6400. Drawing on this deep connection to the A6000 family, the NA-A6400 implements the core features that have come to define Nauticam housings such as intelligent control placement, ease of setup and rugged build quality. Mission Control The NA-A6400 features integrated ergonomic handles with stainless steel stiffening brackets that provide a solid shooting platform and attachment point for lighting accessories. The handles can be adjusted outwards to accommodate larger hands or thick gloves. A large dual-stage trigger is easily reached from the right handle and provides accurate actuation of autofocus and shutter release. A thumb lever on the right side of the housing triggers the Magnify control key which can be used to control AF/MF-AEL. This control can be customized in-camera to lock or activate autofocus. This back-button autofocus control is a favorite of underwater users as it separates autofocus activation from the shutter release to prevent unwanted refocusing during sequential shots or during video shooting. A dedicated record button to trigger video recording is within easy reach of the right handle and colored red for easy identification. Switching between the high-resolution Electronic Viewfinder (EVF) and the LCD display is accomplished with a clearly marked lever to the right of the housing's viewfinder. The camera is securely mounted on a tray using a knurled thumb screw that attaches it to the tripod mounting hole on the camera. The LCD can be used in an angled configuration on the tray, making it easier to see underwater and reduce the effects of glare. The tray locks into place inside the housing, preventing it from falling out when the housing is opened and ensuring proper control alignment. Flash Trigger Flash triggering is handled via the A6400's pop-up on-board flash. A lever on the top of the NA-A6400 can be used to open or close the flash inside the housing, eliminating the need to remember engaging the flash before placing the camera in the housing. Sea&Sea-style fiber optic cable connectors are built-in to the forward facing edge of the housing above the port. HDMI Output The NA-A6400 can be used with external monitors such as the SmallHD 502B and the Nauticam NA-502B housing via the Nauticam HDMI 1.4 system. Premium Professional Optics and Accessories A camera system is just that, a system, which means that access to premium optics and accessories can limit the true functionality of even a top-level camera. Nauticam's line of water-contact optics provide true wide-angle and macro performance. The innovative bayonet mounting system or single and dual-flip adapters make installation simple. 45º and 180º magnifying viewfinders enhance the usabliity of the camera's electronic viewfinder.

The mirrorless APS-C segment is seeing several new additions including this follow-up from Sony to its popular A6000 series the A6700. The A6700 borrows much of its technology from both its cinema, vlogging, and full-frame alpha siblings. Sony has mated the 26MP BSI CMOS sensor to its 'Bionz-X' processor to deliver top-tier autofocus and impressive video specs. Nauticam's aluminum housings for the A6000 series offer unparalleled control with an intuitive interface and the NA-A6700 builds on this legacy to produce the finest underwater imaging platform for the Sony A6700. The Sony a6700 E-mount APS-C camera The Sony a6600 offers excellent image quality as well as the latest AI technologies. Sony's APS-C camera has better scene recognition and the latest technologies for photo and video capture. Most important camera specifications 26.0 APS-C Exmor CMOS sensor ISO range of 100-32000 Approximately 550 outputs (CIPA standard) battery 6 K oversampling /4K 60p 4:2:2 10 bit video recording 3 inch display The NA-A6700 Underwater Housing by Nauticam Nauticam is known for ergonomics and an unmatched experience. Key controls are placed at the photographer’s fingertips. The housing and accessories are lightweight, and easy to assemble. The camera drops in without any control presetting, and lens port changes are effortless. NA-A6700 features an integrated handle system. This ergonomic style provides exceptional control access, even with thick gloves, with ideal placement of the shutter release and a thumb-lever to actuate the AE-L / AF-L button from the right handle in addition to the 'C3' customizable button. Nauticam's build quality is well-known by underwater photographers around the globe. The housing is machined from a solid block of aluminum, then hard anodized making it impervious to salt water corrosion. Marine-grade stainless and plastic parts complete the housing, and it is backed by a two-year warranty against manufacturing defects. HDMI 1.4 port With internal 4K HDR video recording and updated autofocus, the NA-A6700, when paired with an external monitor such as the SmallHD 502 Bright 5", offers videographers a large, bright screen with focus and exposure tools.  For HDMI 1.4 output, an HDMI jack is required, as well as a supported monitor enclosure and internal HDMI cable. WWL-C, CMC-1 AND CMC-2 Three in-house Nauticam optics designs, created by Gründer and Managing Director Edward Lai, are the perfect lenses to complete a6600 underwater system. The magic of the pre-sazure lenses is their tremendous versatility, coupled with outstanding performance in the water. Both macro and super wide angle optics are available to the underwater photographer on the same dive. These lenses are completely designed for use in the water and offer the highest image quality available in a wet capture optic today. The WWL-C is a wide-angle converter compatible with several Sony system lenses. The WWL-C is also an ideal complement to the Sony E 16-50mm F3.5-5.6 PZ OSS lens, which offers a diagonal field of view of over 120 degrees! With both lenses on the camera, you get best-in-class center sharpness, corner sharpness and contrast for the clearest wide-angle images possible underwater. CMC-1 and CMC-2 offer the best macro performance available, with two different magnification levels suitable for a variety of macro subjects. With the popular Sony E 16-50mm F3.5-5.6 PZ OSS lens, the CMC-1 can capture a 26mm wide macro frame, while the CMC-2 captures a 33mm wide area. The CMC-2 is less powerful, making it easier to use with a more präcise autofocus. The CMC-1 is best suited for the smallest macro subjects. Macro enthusiasts will certainly want both! Fast and reliable flash release Reliable rapid-fire manual flash triggering is available with the NA-A6700 for a variety of optically fired flashes and utilizes the same flash trigger as the NA-A6600, the Mini Flash Trigger for NA-A6600 (NA36315). The NA-A6700 comes fiber optic ready and accepts the Universal Fiber Optic Cable.  Strobes and arms can be attached to the housing via included 1″ accessory mounting balls.  Electrical strobe triggering is still an option for those with an investment in legacy lighting gear, requiring the purchase of an accessory electrical bulkhead (NA25056). Integrated vacuum prüf and moisture warning system The Nauticam vacuum check and leak detection system is available with NA-A6700 as standard equipment. Combined with an optional vacuum valve, this monitoring system provides constant updates on the water-tight and safe-to-dive status of the housing. A simple coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur.

The NA-A7II looks very similar to the NA-A7 and the housings have about the same dimensions. Nevertheless, this is an underwater housing specially tuned for the Sony alpha 7 Mark II. The NA-A7II comes with integrated adjustable grips that feature Nauticam's famous rubberized grip. The AF/MF/AEL button has been specially equipped on the right side of the grip with a direct access lever that can be reached instantly with the right thumb. This allows the button to be programmed for AF-ON, which means that "thumb focus" fans have perfect functionality. The output can be operated at the same time, allowing simultaneous focusing and shooting. As with many Nauticam housings, the playback button is placed on the left thumb, and the three adjustment ratios (shutter speed, aperture, and exposure compensation) can be set quickly and with minimal reach. The ISO button is located immediately near the right thumb, important for videographers. The record button is located in the upper right, preventing shake when starting/stopping video. Underwater Tribe | NA-A7II from Nauticam on Vimeo. The function menu button öopens the general camera settings for a quick menu, and this button is not far away with the right thumb. The programmable C3 button is very accessible and can be programmed for one of several functions. The housing features a switch to toggle between the electronic viewfinder and LCD, allowing quick and safe switching between viewing modes, and supports Nauticam's familiar magnifying viewfinders. A Nauticam mini flash output designed specifically for Sony is an available option that enables the camera to shoot quickly with flood-proof optical cables. The housing includes an M16 connector for an optional HDMI output, Nikonos sync cable, or other external accessory. The NA-A7II accommodates the camera's unexpectedly large grip. Rather than compromise on image quality, Nauticam designers chose to create ports to account for this difference, hence a separate entry in the port table for this housing. High-quality professional look Sony's original A7 and A7R cameras sparked a lot of interest in using full-frame for mirrorless cameras. For the underwater photographer, this enthusiasm quickly waned due to the relatively limited lens selection. Underwater photographers rely on very wide angle lenses and macro lenses, and these were nowhere to be found. This changed spätestens with the release of a 16-35mm wide-angle zoom. This is a lens from the Sony Zeiss partnership, designated the Sony Vario-Tessar T* FE 16-35mm F4 ZA OSS. It's a terrific straight wide-angle zoom that focuses close and offers very good all-around sharpness with medium to large dome ports. Nauticam's 180mm dome is the ideal choice for this lens. For macro lovers, Sony has launched a 90mm macro lens (Sony FE 90mm f/2.8 Macro G OSS). Also available now is a 28mm f/2 lens with fisheye adapter, äsimilar to what Sony did with the fisheye and wide-angle adapter on the 16mm lens for the NEX series. This is an attractive option for fisheye lenses, as it allows for multiple configurations with a single lens. Owners of Canon full-frame lenses such as the EF 8-15mm f/4L Fisheye USM, EF 100mm f/2.8L Macro IS USM or EF 16-35mm f/2.8L II USM will appreciate the versatility of their lenses with the A7 series. This is made possible by a Metabones adapter (Canon EF Lens to Sony NEX Smart Adapter (Mark III or Mark IV)). These lenses are well suited for the A7 series and allow both aperture and autofocus control via the camera. Finder options Precision requires foresight: a camera like the Sony A7 II / A7RII requires perfect focus for optimal results. Fortunately, Nauticam has developed the most user-friendly interchangeable viewfinders on the market. The standard optical glass viewfinder is very good and travel friendly, but many photographers prefer the convenience of a magnified viewfinder with adjustable diopters. Nauticam produces a "straight" 180º magnifying viewfinder and a 45º angled magnifying viewfinder to facilitate the tight-space work often associated with macro shooting. Both viewfinders feature high-quality optics and allow bright viewing of the entire image. A patented external diopter adjustment allows for personalized, pin-sharp adjustment underwater. Viewfinder changes can be performed in less than 30 seconds without tools. Exceptional composition and focus accuracy have never been so accessible.  Vacuum inspection and leak detection system The Nauticam vacuum prüf and leak detection system is available as standard with NA-A7II. Combined with an optional vacuum valve, this monitoring system provides constant updates on the watertight and submersible condition of the housing. The operator can see at a glance the watertight and submersible condition of the walker. A simple coded LED lighting system indicates to the user if the vacuum is stable or if the walker is losing vacuum. Leak detection is integrated into the same circuit so that an audible and visual indication is given when water enters.

The Isotta underwater housing for the Sony A7R V Controls On/off lever for the Sony Alpha 7R V Ergonomic lever for focusing and releasing the camera, easy to use even with gloves on Lens release lever Front command dialC1 button; C2 button; C3 button; C4/delete button Mode dial Still Picture/Movie/S&Q lever Zoom knob Connection safety lever Movie (REC) lever AF-ON lever Rear L dial rear control dial R Lock button rear control dial R Menu button AEL button Multi-selector playback button Buttons on the control wheel Fn button  

Aimed squarely at professional image makers, the Sony Alpha 1 provides a 50MP sensor capable of 30fps burst shooting and 8K video.  It features Sony's latest autofocus system, an incredible 9.44M-dot EVF and a 1/400 sec flash sync speed with the mechanical shutter. Whether you are interested in still photos or video, this camera can do just about anything you need it to.   SONY ALPHA 1 CAMERA The Sony a1 is the company's flagship full-frame interchangeable lens camera.  Designed around the new 50.1MP Exmor RS BSI CMOS sensor and the BIONZ XR processor, the a1 is truly a camera which can do it all.  It's 759 point Fast Hybrid Autofocus system offers advanced subject tracking and real-time eye autofocus on both humans and animals.  The optimized processing within the a1 allows it to achieve 30fps continuous shooting at full resolution along with 8K 30p and 4K 120p 10-bit video recording.    8K 30p recording is possible using the full width of the sensor while 4K 120p uses a 10% crop.  Through a Super 35 crop, oversampled 4K recording is also achievable, via an 5.8K capture area.  For shooters who demand more post production flexibility, 4.3K raw 16-bit recording is possible to an external recorder using the camera's full size HDMI A port.   The a1 has also received major upgrades compared to its predecessors, including a 9.44M-dot OLED EVF with a 240fps refresh rate.  The newly designed shutter allows for flash sync speeds up to 1/400 sec and the body includes dual card slots supporting either CFexpress Type A or SD UHS-II memory cards.   SONY ALPHA A1 KEY SPECIFICATIONS 50.1MP Exmor RS BSI CMOS full-frame sensor 759 point Fast Hybrid AF with tracking 30 fps burst shooting with electronic shutter 9.44M dot OLED viewfinder with 240fps refresh rate 8K 30p and 4K 120p video in 10-bit 4.3K 16-bit Raw video output Dual UHS-II / CFexpress Type A card slots THE NAUTICAM NA-a1 UNDERWATER HOUSING Nauticam has supported the Sony Alpha full-frame line since the original a7 with professional grade aluminum housings that offer intuitive access to all the controls and functions of the cameras. As the cameras have evolved, so have the Nauticam housings. The NA-a1 underwater housing provides fingertip access to all key camera controls in a rugged and reliable aluminum underwater housing. Ergonomic camera control access is one of the defining strengths of a Nauticam housing, and the NA-a1 continues this tradition. Integrated DSLR-housing styled handles with ergonomic rubberized grips and stainless steel stiffening brackets add stability and accessory mounting points. The NA-a1 also features dual rear thumb-levers that are easily reached from the handle that access three of the most-used controls on the rear of the camera. The right lever actuates the AF-ON and RECORD buttons while the left lever is mapped to the PLAY button. Atop the housing on the left side are controls in the form of a MODE dial and FOCUS mode lever. The C1, C2 buttons as well as the EV compensation dial also have direct access from the top of the housing. The C3, which is typically assigned to control switching between the EVF and the LCD screen is easily reachable on the rear of the housing from the left handle. ACCESSORY PORTS The NA-a1 has both an M24 port at the front of the housing for both HDMI 1.4 and HDMI 2.0 connectivity (see sidebar for recommendations) as well as an M14 at the rear for the optional Vacuum Valve (25624). The housing comes with electronics pre-installed for Nauticam's Vacuum Check and Leak Detection system. This monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive. PREMIUM PROFESSIONAL OPTICS Nauticam's wide range of ports and in-house corrective optics are the perfect compliment to the NA-a1's inherent flexibility. Built around the N100 Port System, the NA-a1 supports a wide variety of Sony FE mount lenses, as well as EF mount lenses via adapters. In addition, there are several options available to use the groundbreaking WACP and WACP-2 wide-angle corrective lenses as well as the more compact and in-water removable WWL-1B. For example, With the Sony SEL1635GM FE 16-35mm F2.8 GM, the WACP 2 brings the original 105º field-of-view to an impressive 128º with sharper corners, an ~0" minimum focus distance and a more natural looking image than would be provided by a standard glass dome port. FLASH TRIGGERING Both fiber-optic and electrical strobe triggering options are available. The Nauticam Universal Fiber Optical cables attach to the built-in bulkheads atop the housing and feature modular connections for both Sea&Sea-style bushings and INON threaded connections. Triggering is achieved using the optional Nauticam Mini Flash Trigger for Sony (26302) which uses LEDs powered by an on-board coin-cell battery to generate a manual signal that is transmitter via the optical cables to compatible strobes.

Take your underwater videography to new depths with the NA-ZVE1 designed for the Sony ZV-E1 Camera. With its compact size, 12.1 MP Full Frame Back Illuminated sensor, advanced image processing, and AI subject recognition, this housing and camera combination unlocks limitless creative possibilities. It's the world's most lightweight and compact full-frame camera with interchangeable lenses. The NA-ZVE1 was built with the image maker in mind making sure all essential camera controls are positioned at your finger tips. ensuring ease of use in challenging environments.  THE SONY ZV-E1 CAMERA The Sony ZV-E1 is a compact and lightweight camera that packs a punch with its high-end video specifications. It features a 12MP Quad Bayer BSI full frame sensor and an ISO range of 80-102,400, extendable to 40-409,600. The ZV-E1 is capable of recording 4K 60p with no sensor crop and 4K 120p with a small 1.1x crop, offering 10-bit 4:2:2 internal recording with S-Log2, S-Log3, and S-Cinetone. It has a single card slot compatible with SD UHS-II. The camera lacks a viewfinder, instead featuring a rear LCD monitor with advanced touch screen capabilities. The ZV-E1 is equipped with a dedicated AI processing unit that can recognize subjects more in-depth, making it a powerful tool for videography. It also introduces a new option for image stabilization, and offers unique features such as Breathing Compensation and CineVlog mode. The release of the ZV-E1 is exciting because it brings high-end video specifications, previously only available in more expensive models like the Sony A7S III, to a more affordable and compact package. This makes advanced videography more accessible to a broader range of creators. Key Camera Specs 12MP full-frame CMOS sensor with no mechanical shutter UHD 4K video at up to 60p without crop Full HD (1080) footage at up to 120p 10-bit 4:2:2 capture (All-I or LongGOP) 4K/120p and 1080/240 will be added later (a paid upgrade in some regions) 5-axis image stabilization UVC 4K/30p video stream when plugged in as USB device Unlimited 4K/30p, 30 minutes 4K/60p (at 25°C) Single UHS-II SD slot Micro HDMI slot 483g including battery NAUTICAM NA-ZVE1 UNDERWATER HOUSING Nauticam is the industry leader in mirrorless interchangeable lens underwater camera support. Nauticam has housed more mirrorless cameras, and more Sony E Mount cameras than any other housing manufacturer. This experience results in the most evolved housing line with broadest range of accessories available today. Pioneering optical accessories elevate performance to a new level. Magnifying viewfinders, the sharpest super macro accessory lenses ever made, and now the highest quality water contact wide angle lenses (the WWL and WACP family) combine with the NA-ZVE1 housing to form a complete imaging system. Nauticam is known for ergonomics, and an unmatched experience. Key controls are placed at the photographer’s fingertips. The housing and accessories are light weight, and easy to assemble. The camera drops in without any control presetting, and lens port changes are effortless. NA-ZVE1 features an integrated handle system. This ergonomic style provides exceptional control access, even with thick gloves, with ideal placement of the shutter release and a thumb-lever to actuate the AF-ON button from the right handle. Nauticam build quality is well known by underwater photographers around the globe. The housing is machined from a solid block of aluminum, then hard anodized making it impervious to salt water corrosion. Marine grade stainless and plastic parts complete the housing, and it is backed by a two year warranty against manufacturing defects. HDMI CONNECTIVITY The NA-ZVE1 features an M24 bulkhead which supports the Nauticam HDMI 2.0/1.4 cable system which can be paired with supported external monitors/recorders. Two of the most popular external monitors setups are the Atomos Ninja V and the newly released SmallHD Ultra 5.   PREMIUM PROFESSIONAL OPTICS Optical performance is just as necessary as camera performance and this becomes even more critical given the challenges of filming underwater. The Nauticam NA-ZVE1 uses the same N100 Port System as other Sony full-frame mirrorless housings which makes for a seamless transition for those upgrading or looking to add an additional camera to their lineup. While this system provides exceptional optical-glass and flat port solutions for a wide variety lenses, the real power can be realized using Nauticam's Water Contact Optics. This lineup of dry and wet lenses are conceived using commercial lens-design software to achieve truly unparalleled underwater image quality both for stills and video in both macro and wide-angle situations. While there are many options, we'll focus on the most compact and versatile setup to match the travel friendly size of the ZV-E1.   WWL-1B is a wide angle conversion lens, compatible with the Sony FE 28-60mm f/4-5.6 lens, providing 130 degree diagonal field of view with full zoom through! The WWL-1B offers class leading center sharpness, corner sharpness, and contrast resulting in some of the best wide angle images possible underwater. CMC-1 and CMC-2 provide the best macro performance for the Sony FE 28-60mm f/4-5.6 lens, with two different magnification strengths, suitable for a wide variety of macro subjects.  CMC-2 is less strong, making it easier to use with more accurate autofocus. CMC-1 is best suited for the smallest of macro subjects. Macro enthusiasts will surely want both! The WACP-C and WACP-1 achieve ultra-wide 130º fields-of-view with reduced distortion over conventional optics while featuring ~0" minimum focus distances, zoom through capabilities and unbeatable corner sharpness at even wide-open apertures such as F5.6.   VACUUM CHECK AND LEAK DETECTION The Nauticam vacuum check and leak detection system is shipped with NA-ZVE1 as standard equipment. With the addition of the optional M14 Vacuum Valve (25624) this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

Techniques and innovations based on years of experience have resulted in an easy-to-use, highly professional product. Perfect handling of the Canon EOS 5D Mark III body is made possible by adjustable grips that fit the human hand and make holding the camera very comfortable, even on long dives. Easy access to all key camera controls with clearly labelled, laser engraved, durable buttons, even when wearing gloves and dry diving gloves. An easy and quick release camera mounting plate allows camera positioning and a lever locks the compartment inside the housing. The back door has a large scratch-resistant window glass for a fine camera display and optical viewfinder, and is completely separated from the front body to facilitate camera mounting. External viewfinders can be mounted, INON X-2 compatible.  Open and close with one hand The Canon EOS 5D Mark III housing is locked with Isotta's one-handed, single-turn knob. It is the only single locking mechanism on the DSLR housing market. It is quick, easy and secure thanks to its double steel bolts on the underside of the housing. Ports and extensions A range of ports and extension rings are available in a dedicated section. The detachable port mounts to the Canon EOS 5D Mark III thanks to markers and a 120mm bayonet mount. The interchangeable port bodies and extension rings allow the use of most lenses on the market for maximum versatility and performance. Light The housing of the Canon EOS 5D Mark III offers the possibility to use external flashes via two standard light connectors as well as two Nikonos sync cable sockets. This allows for easy mounting of all flash and lighting equipment. Construction and safety Only the best materials are used in the manufacture of our enclosures, such as anodised aluminium, which is corrosion-resistant and thermally coated, and stainless steel. A durable product that requires easy and quick maintenance by the user. Two high quality O-ring seals protect and ensure perfect and safe waterproofing for all moving and removable parts; a red moisture/water alarm inside the housing is powered by a user replaceable battery. Working depth 100 metres. Various accessories can be attached using the M8 hole on the top of the housing and the double M6 threaded holes on the bottom of the housing. Special features: Ergonomic side handles, adjustable (via optional accessories); Two fibre optic connectors (optional); Two standard sync cable sockets; Rear housing is fully detachable from the front housing; Locking compartment for easy camera mounting; One-hand lock for rear housing; One M16 connector for installation of accessories, e.g. vacuum valves or monitors; Aluminium buttons and dials with engraved symbols identical to the camera controls; all camera controls are external; Viewfinder glass with wide back; Optical viewfinder;  double O-ring seals on all buttons and removable parts;  Humidity sensor with LED and audible indicator (replaceable battery); Removable port - 120mm bayonet; Safety lock on ports to prevent accidental opening;  Wide, rubberised feet for firm footing;  M8 hole on top of housing for various accessories such as focus lamps; Two M6 holes on the bottom of the housing for various accessories such as mounts for flash units or tripods;  External viewfinders can be mounted, INON X-2 compatible; 

The housing for Canon EOS 5D Mark IV allows to capitalize on the camera full potential and to capture amazing pictures underwater. Product details An easy to use, highly professional product has been created through techniques and innovations gained from years of experience. The perfect handling of the Canon EOS 5D Mark IV housing is possible by means of adjustable handles crafted to match the human hand and make holding the camera very comfortable even throughout long dives. Easy access to all key/main camera controls by means of clearly labelled laser-engraved longlasting buttons, even with gloves and drysuit gloves. An easy and quick release camera mounting plate allows the camera positioning and a lever locks the tray inside the housing. The back door has a large window anti-scratch glass for a fine camera display and optical viewfinder view and it is entirely detached from the front body to make easier the camera fitting. External viewfinders can be mounted, INON X-2 compatible.  ONE HAND OPEN/CLOSE The housing for Canon EOS 5D Mark IV is closed with Isotta’s single handed one-turn knob. It’s the only single latch closing mechanism in the DSLR housing market. It’s fast, simple and secure thanks to its double steel pins at the bottom on the housing. PORTS AND EXTENSION RING A series of ports and extension rings are available in dedicated section. The removable port is fitted thanks to markers and a bayonet 120 mm connection to the Canon EOS 5D Mark IV. The interchangeable port bodies and extensions rings combine to allow the use of most of lenses on the market for maximum versatility and performance. LIGHTING The housing for Canon EOS 5D Mark IV offers the possibility to use external strobes via two standard optical light ports (trigger not included) as well as two optional Nikonos N5 or S6 sync cord bulkheads. This allows for easy mounting of any strobe and lighting set up in manual mode. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such anodized aluminum, which is anticorodal and thermo-coated, and stainless steel. A longlasting product that requires easy and simple maintenance by the user. Dual high-quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth 100 metres. Different accessories can be fitted by means of M8 hole positioned on upper side of the housing and double threaded M6 holes located on housing bottom side. Highlights Ergonomic side handles, adjustable (via optional accessory) Two fiber optic connectors, not included Two standard electrical sync cord bulkheads Nikonos N5 or S6 not included Back housing completely detachable from the front housing; Tray with lock for an easy fitting of the camera Single-hand closing knob for back housing One M16 port for installation of accessories, e.g. vacuum valves or monitors Aluminum buttons and dials with engraved symbols identical to camera controls All camera controls are external Wide back display viewfinder glass Optical viewfinder Dual O-Ring seals on all buttons and removable parts Moisture sensor with LED and audible indicator (replaceable battery) Removable port - 120mm bayonet Ports security latch to prevent accidental opening Wide, rubber covered feet for solid footing M8 hole located on upper side of the housing for various accessories such as focus lights wo M6 holes located on housing bottom side for different accessories such as brackets for strobes or tripods External viewfinders can be mounted, INON X-2 compatible

MDX-R5 - U/W HOUSING FOR CANON EOS R5 Revised ergonomic design, improved safety features and eye-catching exterior. The new MDX series housings are now upgraded with more standard features to ensure better handling and greater protection for your camera Features Equipped with Grip plus,SA8 Fixed Ball Bases The new MDX R5 is the perfect complement to Canon`s new mirrorless R5 camera. The MDX-R5 is rich in features with all controls ergonomically designed to maximize camera operation. All major camera functions can be accessed from the grip handles through thumb or finger movement without releasing your grip. Sea&Sea Optical Converter and S&S manual flash trigger compatibility, port locking system plus removal and attaching of lenses while camera is still in housing. Compatible with both native RF lenses and all EF lenses (with mount). In addition, a 24mm port has been included to accommodate HDMI 2 cables for connection to an external video monitor to realize the full potential of the cameras ultra-high video capabilities. A built-in Leak Sensor and a bulkhead for external vacuum sensor provides double protection and increased peace of mind for your camera equipment while diving. Many more features are available on the MDX R5 to help you gain full potential of all the R5`s features and make your underwater imaging experience unforgettable. MDX-R5 with YS-D3 Strobes For better noticeability, controls are partially colored with yellow. All major controls for camera function can be easily operated without releasing your grip on the handle, providing stability and assurance during all imaging situations  Compatible with the Sea&Sea, “Manual Flash Trigger” (optional). and Sea&Sea Optical TTL Coverter. 24mm bulkhead allows connection of 3rd party HDMI 2 cable for attaching an external video monitor     Bulkhead will accept the S&S Vivid housing Vacuum Leak Sensor, or an optional 16mm step down converter is available to fit third party vacuum sensors   Compatible with all the DX (NX) series ports. The camera can be removed from the housing easily even if a lens with large diameter such as the RF15~35 f2.8 is mounted on the camera without removing port from the housing enabling you to replace battery and lens with ease. MDX-R5 Other Features The Port lock prevents the port from turning or loosening and the Port Lock lever is specifically located to avoid being unlocked accidentally.  The housing is equipped with a lens-lock release button which makes it possible to change lenses easily, without opening the housing. Pulling out the Focus/Zoom Dial gives sufficient room inside the housing to easily accommodate larger diameter lenses. All controls have luminescense stickers which glow in a dark enbironment for better visibility of controls. Equipped with Optical Viewfinder 0.5x as standard. Other optional viewfinders such as the VF180 1.2x,VF45 1.2x and Optical Viewfinder 0.66x,0.8x can be used.?Some vignetting may occur when the VF180 1.2x is mounted on housing, the upper part of the camera's viewfinder cannot be viewed dus to vignetting. Sync Cord 2-pin Connector enables use of conventional hardwired Sync cable (Manual mode only). Equipped with two sacrificial zinc diodes (one on the fornt case and the other on the rear) to prevent electrolysis damege. Built-in leak sensor immediately alerts alerts you to water ingress.Tripod screw mount is located on the center underside of the housing. Equipped with an under guard to protect housing from scratches and abrasion    

MDX-R5 U/W HOUSING FOR CANON EOS R5 Revised ergonomic design, improved safety features and eye-catching exterior. The new MDX series housings are now upgraded with more standard features to ensure better handling and greater protection for your camera Features Equipped with Grip plus,SA8 Fixed Ball Bases The new MDX R5 is the perfect complement to Canon`s new mirrorless R5 camera. The MDX-R5 is rich in features with all controls ergonomically designed to maximize camera operation. All major camera functions can be accessed from the grip handles through thumb or finger movement without releasing your grip. Sea&Sea Optical Converter and S&S manual flash trigger compatibility, port locking system plus removal and attaching of lenses while camera is still in housing. Compatible with both native RF lenses and all EF lenses (with mount). In addition, a 24mm port has been included to accommodate HDMI 2 cables for connection to an external video monitor to realize the full potential of the cameras ultra-high video capabilities. A built-in Leak Sensor and a bulkhead for external vacuum sensor provides double protection and increased peace of mind for your camera equipment while diving. Many more features are available on the MDX R5 to help you gain full potential of all the R5`s features and make your underwater imaging experience unforgettable. MDX-R5 with YS-D3 Strobes For better noticeability, controls are partially colored with yellow. All major controls for camera function can be easily operated without releasing your grip on the handle, providing stability and assurance during all imaging situations   Compatible with the Sea&Sea, “Manual Flash Trigger” (optional). and Sea&Sea Optical TTL Coverter. 24mm bulkhead allows connection of 3rd party HDMI 2 cable for attaching an external video monitor Bulkhead will accept the S&S Vivid housing Vacuum Leak Sensor, or an optional 16mm step down converter is available to fit third party vacuum sensors Compatible with all the DX (NX) series ports. The camera can be removed from the housing easily even if a lens with large diameter such as the RF15~35 f2.8 is mounted on the camera without removing port from the housing enabling you to replace battery and lens with ease. MDX-R5 Other Features The Port lock prevents the port from turning or loosening and the Port Lock lever is specifically located to avoid being unlocked accidentally.  The housing is equipped with a lens-lock release button which makes it possible to change lenses easily, without opening the housing. Pulling out the Focus/Zoom Dial gives sufficient room inside the housing to easily accommodate larger diameter lenses. All controls have luminescense stickers which glow in a dark enbironment for better visibility of controls. Equipped with Optical Viewfinder 0.5x as standard. Other optional viewfinders such as the VF180 1.2x,VF45 1.2x and Optical Viewfinder 0.66x,0.8x can be used.?Some vignetting may occur when the VF180 1.2x is mounted on housing, the upper part of the camera's viewfinder cannot be viewed dus to vignetting. Sync Cord 2-pin Connector enables use of conventional hardwired Sync cable (Manual mode only). Equipped with two sacrificial zinc diodes (one on the fornt case and the other on the rear) to prevent electrolysis damege. Built-in leak sensor immediately alerts alerts you to water ingress.Tripod screw mount is located on the center underside of the housing. Equipped with an under guard to protect housing from scratches and abrasion

Underwater housing X-2 R5 by INON A housing for Canon EOS R5 INON strobe compatible ultra-accurate multi-functional built-in "TTL Converter" as standard feature Control flash amount directly from camera 12 shots/sec. continuous shooting supported Equipped with “Quick Shoe System” for quick switch between horizontal and vertical camera composition Standard “Vacuum Leak Sensor (PAT. P)" checks housing sealing in only 5 minutes MRS port further evolves to support fine manual focusing Optional two viewfinders provide bright and clear finder image Lightweight and compact ultra-precision cast aluminum body Ultra-accurate multi-functional built-in "TTL Converter"    The "TTL Converter" equipped as a standard feature, triggers INON strobe optically to enjoy fully automatic TTL. Exclusively developed for INON strobe based on its flash protocol to optimize its performance for underwater use. As an underwater strobe manufacturer, we successfully achieved the TTL Converter that provides constant, stable and highly accurate TTL exposure. Strobe manual power is directly adjustable from camera INON strobe manual power is directly adjustable from camera ranging between 1/64 and FULL at 1/3EV. increments. Useful when strobe is positioned away like on long strobe arm or when shooting with backlit technique. 12 shots/sec. continuous strobe firing ***** The TTL Converter fully supports [High speed continuous][High speed continuous+]. With ultra-accurate TTL shooting is now available for continuous shooting based on electricity stored in a capacitor6. INON TTL Converter strives efficiency in battery consumption not to miss precious moment and successfully provides more than 100,000 flash triggering only by two CR2032 coin batteries. Built-in Quick Shoe System supports quick camera composition Change The base plate is INON's unique Arca Swiss style "Quick Shoe Main Base". The "Quick Shoe W50 Plate" on the bottom and side of the housing allows you to quickly change to vertical composition. In addition to vertical composition without changing lighting position, it also allows you to shoot vertical composition from low angle which is not possible with conventional system.   Built-in "Vacuum leak sensor" confirms housing sealing in 5 minutes The "Vacuum Leak Sensor" ensures housing sealing by monitoring air pressure inside of the housing during leak check and warns accidental flooding with LED blinks and buzzer during diving. The onboard pressure sensor changes sensitivity for leak check and diving by variable control program (PAT. P).  The supersensitive pressure sensor detects even fine leakage. Not as like conventional leak sensors, it drastically shortens test time (from 30 seconds to 5 minutes). The sensitivity of the dive mode eliminates false alarm even when ambient temperature changes. New S-MRS Port Newly developed S-MRS (Magnetic Rotary System) controls focusing and zooming by magnetic attraction. The new S-MRS provides smoother operation with less play or rattle comparing to the previous model. By combining the EOS R5 with an RF lens, the MF Peaking function can also be used during full-time manual focusing. Together with the focus guide function, this enables ultra-precise focusing.  Maximum three MRS Control Rings can be installed to control the Control Ring, Focus Ring and SA Control Ring. Lightweight and compact ultra-precision cast aluminum body The X-2 R5 is made from corrosion resistance aluminum alloy by ultraprecise cast manufacturing technique to fuse design, weight and durability in higher dimension. The cast manufacturing technique enables thin body plate with complicated curved design which is not possible with machining. Lightweight and durable aluminum alloy body has acquired reliability, durability and controllability even in severe underwater.

THE CANON EOS R5C CAMERA The Canon EOS R5C is the latest in Canon's full-frame mirrorless camera lineup which has gained unprecedented demand.  It features the RF lens mount which has the same large 54mm diameter but the ability to have larger rear lens elements that are closer to the sensor gives increased corner and outer edge sharpness.  The R5C uses an all new 45MP CMOS sensor with in-body image stabilization which can reduce shake by up to 8 stops.  The camera's Dual Pixel autofocus system uses 1053 autofocus points across the entire frame.   It is also capable of recording 8K video at 24p or 30p and 4K at up to 120p.   The EOS R5C can also use the large EF-mount lens lineup via three optional adapters, a simple EF to R adapter, one which supports the customizable control ring and another that features a drop-in filter mount. Key Camera Specifications 45MP full-frame Dual Pixel CMOS sensor 8K Video, with option for RAW or 10-bit 4:2:2 C-log or HDR PQ Up to 4K/120p, or oversampled 4K up to 30p 100% coverage Dual Pixel II AF system 12 fps / 20 fps burst (mechanical / electronic shutter) 5.76M-dot OLED EVF with 120fps max refresh rate 3.2" 2.1M-dot fully articulating touchscreen 10-bit HDR photos in HEIF format 1x CFExpress slot, 1x UHS-II SD slot Weather sealing   THE NAUTICAM NA-R5C UNDERWATER HOUSING FOR THE CANON EOS R5C CAMERA The NA-R5C underwater housing follows suit with Nauticam's drive for innovation. Both the Canon EOS R5C and EOS R present shooters with the ability to use both the available legacy EF lenses via an adapter in addition to their native RF optics.  To support both the legacy and native lenses, Nauticam has integrated the NA-R5 into the N120 port system. Canon's EF to RF mount adapters can be affixed to the camera before insertion into the housing. When using the EOS RC5 inside the housing with the adapter and a supported EF lens, the port and extension ring arrangement will be identical to the same setup on a Nauticam Canon N120 DSLR. As the RF lens lineup emerges, dedicated port and extension ring combinations will be listed on the Port Chart. Two lens release buttons, one for RF and one for EF lenses used with the optional Canon adapter, are located on the front of the housing to make lens removal through the port opening simple. Mission Control Nauticam engineers are obsessed with getting the underwater image maker unfettered access to all the necessary controls, with as many within easy reach of the ergonomic rubberized handles. This Mission Control philosophy extends to the NA-R5C where a dual thumb lever and dual sub-lever are placed by the right handle. The upper thumb lever activates the "AF-On" and the lower the "Q" buttons while the sub-lever corresponds to the "M-Fn" and "Record" buttons. Near the left handle is a thumb lever for "Playback" as well as a dedicated switch to change from using LCD to the EVF. Large knurled and rubberized control dials access the camera's "main" and "sub" command dials. The two-stage trigger allows for smooth focus and firing activation. Additional buttons for "Menu", "Focus Point Selection" and others are also easily reached from the handles. An additional control wheel is located on the left side of the housing and will interface with the control ring on the supported EF to EOS R Mount Adapter with Control Ring using the optional gear (NA19561). Flash Triggering Flash triggering is achieved via one of two optional Flash Triggers, a manual LED trigger (NA26301) or a TTL Flash Trigger (NA26321) that use the built-in fiber optic bulkheads with optional fiber-optic cables to trigger supported strobes. For controlling strobes that do not support fiber optic flash triggering, a variety of legacy hot-shoe flash control bulkheads are available. INTEGRATED VACUUM CHECK AND LEAK DETECTION SYSTEM The Nauticam vacuum check and leak detection electronics are shipped with the NA-R5C as standard equipment. Combined with an accessory vacuum valve this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

The Canon EOS R6 II Camera The Canon EOS R6 Mark II is one of the latest in Canon's full-frame mirrorless camera lineup which has gained unprecedented demand.  It features the RF lens mount which has the same large 54mm diameter but the ability to have larger rear lens elements that are closer to the sensor gives increased corner and outer edge sharpness.  TThe R6 Mark II uses an all new 24MP CMOS sensor which boosts the resolution from its predecessor and also significantly improves its rolling shutter performance. It offers in-body image stabilization rated at up to 8 stops of correction. The camera's Dual Pixel CMOS AF II autofocus system uses 1053 autofocus points across the entire frame. It is also capable of recording 4K video at up to 60p internally and 6K 60p extern The EOS R6 Mark II can also use the large EF-mount lens lineup via the Canon RF to EOS R Adapter. Key specifications 24.2MP full-frame CMOS sensor UHD 4K shooting up to 60p, 1080 at up to 120p, 6K ProRes RAW recording externally up to 60p 100% coverage Dual Pixel II AF system 12 fps / 40 fps burst (mechanical / electronic shutter) 3.69M-dot OLED EVF 3" 1.62M-dot vari-angle touchscreen LCD 580 shot-per-charge battery rating Dual UHS-II SD slots The Nauticam Underwater Housing for the Canon EOS R6 Mark II Camera The NA-R6II underwater housing follows suit with Nauticam's drive for innovation and it supports both the Canon EOS R6 and R6 Mark II. A conversion kit is required for the original R6 and will be provided upon request. Like its predecessors, the NA-R6II presents shooters with the ability to use both the available legacy EF lenses via an adapter in addition to their native RF optics. To support both the legacy and native lenses, Nauticam has integrated the NA-R6II into the N120 port system. Canon's EF to RF mount adapters can be affixed to the camera before insertion into the housing. When using the EOS R6 Mark II inside the housing with the adapter and a supported EF lens, the port and extension ring arrangement will be identical to the same setup on a Nauticam Canon N120 DSLR. With the ever growing RF lens lineup, you can also follow the dedicated N120 Canon RF port chart that is being updated and expanded with each new lens release. Please note that the Canon Control Ring and Drop-in Filter EF to EOS R adapters are not accessible within the housing. Mission Control Nauticam engineers are obsessed with getting the underwater image maker unfettered access to all the necessary controls, with as many within easy reach of the ergonomic rubberized handles. This Mission Control philosophy extends to the NA-R6II where a dual thumb lever and sub-lever are placed by the right handle. The dual thumb lever on the front right side activates the "M-Fn" and "Rec" buttons while the sub-lever on the right rear side corresponds to the "AF-ON" button. Near the left handle is a thumb lever for "Playback" for easy image review. Large knurled and rubberized control dials access the camera's "main" and "sub" command dials. The two-stage trigger allows for smooth focus and firing activation. Additional buttons for "Menu", "Focus Point Selection" and others are also easily reached from the handles Flash Triggering Flash triggering is achieved via one of two optional Flash Triggers, a manual LED trigger (NA26301) or a TTL Flash Trigger (NA26321) that use the built-in fiber optic bulkheads with optional fiber-optic cables to trigger supported strobes. For controlling strobes that do not support fiber optic flash triggering, a variety of legacy hot-shoe flash control bulkheads are available. Integrated Vacuum Check and Leak Detection System The Nauticam vacuum check and leak detection electronics are shipped with the NA-R6 as standard equipment. Combined with an accessory vacuum valve (NA25625) this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive. HDMI Recommended Configurations For HDMI 2.0 Cable System NA25086 M24 adaptor for HDMI 2.0 Cable 25077 M24D1R205-M28A1R170 HDMI 2.0 Cable (for NA-XT3/R5 to use with Ninja V housing) NA17922 Nauticam Atomos Ninja V Housing for Atomos Ninja V 5” 4Kp60 4:2:2 10-bit Reorder/Monitor/Player (excl. HDMI 2.0 cable) NA17922S Nauticam Atomos Ninja V-S Housing for Atomos Ninja V 5” 4Kp60 4:2:2 10-bit Reorder/Monitor (excl. HDMI 2.0 cable) with Atomos AtomX SDI Module For HDMI 1.4 Cable System NA25033 Standard HDMI Cable with M16 Thread NA25081 M24-M16 Step Down Adaptor NA25076 HDMI (D-D) Cable in 200mm Length for NA-XT2/NA-XH1/NA_A6400

Underwater housing X-2 R6 Mark II by INON A housing for Canon EOS R6 Mark II INON strobe compatible ultra-accurate multi-functional built-in "TTL Converter" as standard feature Control flash amount directly from camera 12 shots/sec. continuous shooting supported Equipped with “Quick Shoe System” for quick switch between horizontal and vertical camera composition Standard “Vacuum Leak Sensor (PAT. P)" checks housing sealing in only 5 minutes MRS port further evolves to support fine manual focusing Optional two viewfinders provide bright and clear finder image Lightweight and compact ultra-precision cast aluminum body Ultra-accurate multi-functional built-in "TTL Converter"    The "TTL Converter" equipped as a standard feature, triggers INON strobe optically to enjoy fully automatic TTL. Exclusively developed for INON strobe based on its flash protocol to optimize its performance for underwater use. As an underwater strobe manufacturer, we successfully achieved the TTL Converter that provides constant, stable and highly accurate TTL exposure. Strobe manual power is directly adjustable from camera INON strobe manual power is directly adjustable from camera ranging between 1/64 and FULL at 1/3EV. increments. Useful when strobe is positioned away like on long strobe arm or when shooting with backlit technique. 12 shots/sec. continuous strobe firing ***** The TTL Converter fully supports [High speed continuous][High speed continuous+]. With ultra-accurate TTL shooting is now available for continuous shooting based on electricity stored in a capacitor6. INON TTL Converter strives efficiency in battery consumption not to miss precious moment and successfully provides more than 100,000 flash triggering only by two CR2032 coin batteries.   Built-in "Vacuum leak sensor" confirms housing sealing in 5 minutes The "Vacuum Leak Sensor" ensures housing sealing by monitoring air pressure inside of the housing during leak check and warns accidental flooding with LED blinks and buzzer during diving. The onboard pressure sensor changes sensitivity for leak check and diving by variable control program (PAT. P).  The supersensitive pressure sensor detects even fine leakage. Not as like conventional leak sensors, it drastically shortens test time (from 30 seconds to 5 minutes). The sensitivity of the dive mode eliminates false alarm even when ambient temperature changes. New S-MRS Port Newly developed S-MRS (Magnetic Rotary System) controls focusing and zooming by magnetic attraction. The new S-MRS provides smoother operation with less play or rattle comparing to the previous model. By combining the EOS R5 with an RF lens, the MF Peaking function can also be used during full-time manual focusing. Together with the focus guide function, this enables ultra-precise focusing.  Maximum three MRS Control Rings can be installed to control the Control Ring, Focus Ring and SA Control Ring. Lightweight and compact ultra-precision cast aluminum body The X-2 R6 II is made from corrosion resistance aluminum alloy by ultraprecise cast manufacturing technique to fuse design, weight and durability in higher dimension. The cast manufacturing technique enables thin body plate with complicated curved design which is not possible with machining. Lightweight and durable aluminum alloy body has acquired reliability, durability and controllability even in severe underwater.