Underwater housing X-2 R6 Mark II by INON A housing for Canon EOS R6 Mark II INON strobe compatible ultra-accurate multi-functional built-in "TTL Converter" as standard feature Control flash amount directly from camera 12 shots/sec. continuous shooting supported Equipped with “Quick Shoe System” for quick switch between horizontal and vertical camera composition Standard “Vacuum Leak Sensor (PAT. P)" checks housing sealing in only 5 minutes MRS port further evolves to support fine manual focusing Optional two viewfinders provide bright and clear finder image Lightweight and compact ultra-precision cast aluminum body Ultra-accurate multi-functional built-in "TTL Converter"    The "TTL Converter" equipped as a standard feature, triggers INON strobe optically to enjoy fully automatic TTL. Exclusively developed for INON strobe based on its flash protocol to optimize its performance for underwater use. As an underwater strobe manufacturer, we successfully achieved the TTL Converter that provides constant, stable and highly accurate TTL exposure. Strobe manual power is directly adjustable from camera INON strobe manual power is directly adjustable from camera ranging between 1/64 and FULL at 1/3EV. increments. Useful when strobe is positioned away like on long strobe arm or when shooting with backlit technique. 12 shots/sec. continuous strobe firing ***** The TTL Converter fully supports [High speed continuous][High speed continuous+]. With ultra-accurate TTL shooting is now available for continuous shooting based on electricity stored in a capacitor6. INON TTL Converter strives efficiency in battery consumption not to miss precious moment and successfully provides more than 100,000 flash triggering only by two CR2032 coin batteries.   Built-in "Vacuum leak sensor" confirms housing sealing in 5 minutes The "Vacuum Leak Sensor" ensures housing sealing by monitoring air pressure inside of the housing during leak check and warns accidental flooding with LED blinks and buzzer during diving. The onboard pressure sensor changes sensitivity for leak check and diving by variable control program (PAT. P).  The supersensitive pressure sensor detects even fine leakage. Not as like conventional leak sensors, it drastically shortens test time (from 30 seconds to 5 minutes). The sensitivity of the dive mode eliminates false alarm even when ambient temperature changes. New S-MRS Port Newly developed S-MRS (Magnetic Rotary System) controls focusing and zooming by magnetic attraction. The new S-MRS provides smoother operation with less play or rattle comparing to the previous model. By combining the EOS R5 with an RF lens, the MF Peaking function can also be used during full-time manual focusing. Together with the focus guide function, this enables ultra-precise focusing.  Maximum three MRS Control Rings can be installed to control the Control Ring, Focus Ring and SA Control Ring. Lightweight and compact ultra-precision cast aluminum body The X-2 R6 II is made from corrosion resistance aluminum alloy by ultraprecise cast manufacturing technique to fuse design, weight and durability in higher dimension. The cast manufacturing technique enables thin body plate with complicated curved design which is not possible with machining. Lightweight and durable aluminum alloy body has acquired reliability, durability and controllability even in severe underwater.

With Canon EOS R6 the producer has focused on the photographer's creativity, wanting to support the user in his artistic flair with a camera defined as "radical". With silent shooting at 20 fps, Dual Pixel CMOS AF II sensors and ISO 102,400 this camera promises to meet expectations even under water, allowing you to photograph moving subjects even in low-light. The image stabilizer, 20 megapixel photos and the ability to shoot 4K video, make this camera complete. Built for speed, it produces up to 240 images in RAW format. The possibility of using the double memory card certainly helps to shoot more lightly. Product details Canon EOS R6 Underwater Housing by Isotta The housing respects all the key points of Isotta's line of housings: one-handed opening, double O-ring seals for greater safety, the use of high quality materials and the made in Italy craftsmanship. The housing was created to follow the lines of the camera, resulting small and manageable, while ensuring complete control of camera functions and absolute freedom in the use of accessories. MAN BEFORE MACHINE! The focus in the study of the housing goes to the diver who decides to use it. The comfort in the use and management of the machine in water is a fixed point, studied in every detail. The handles are ergonomic, adjustable and interchangeable*. if necessary; the housing is compact and lightweight, so you won't tire your arm too much and have an excellent control over stability. All buttons are conveniently reachable from the grip position of the handles ensuring maximum management of the camera with minimum effort. The rear back offers a full view of the camera screen so that you can shoot in live view unobstructed and in comfort and it detaches completely from the front body so that it is easy to insert the camera and perform operations inside the housing. The presence of the viewfinder allows you to take pictures framing in the classic way and to replace it with a magnifier. The closing knob is Single-hand actionable. MORE AND MORE CUSTOMIZABLE! Supplied with only the connections for the optical fiber, the housing has been designed with three M16x1 connections and one M24x1 connection, for total freedom in the choice of the conformation of the equipment. When ordering, you can select your preferred lighting control system choosing between Trigger, Sincro N5 or S6 and your right port system. Through the different combinations between ports and extension rings it is possible to use most of the lenses on the market. Various accessories can be used by means of an M8 hole located at the top of the case and two M6 threaded holes located at the bottom. To make it even more unique, have your name or logo engraved. SAFETY IS IMPORTANT! The locking pins on the back are made of stainless steel and penetrate the shell for added strength and security. The housing is made of aluminum, resistant and anti-corrosion, anodized in the unmistakable red color. The classic double o-ring seal is on all moving and removable parts ensures an optimal watertight seal. The camera is held straight, centered and in place by a mounting plate with a safety catch, which slips nimbly into the housing. NNo risk of sudden infiltration. A red humidity alarm inside the case is powered by a user-replaceable battery and instantly signals an increase in humidity in a critical area. Watertightness is guaranteed up to a maximum depth of 100 meters. Highlights Ergonomic side handles, adjustable (via optional accessory) Two built-in fiber optic connectors Two standard electrical sync cord bulkheads Nikonos N5 or S6 not included Back housing completely detachable from the front housing Tray with lock for an easy fitting of the camera Single-hand closing knob for back housing Three M16x1 port for installation of accessories, e.g. vacuum valves or monitors One M24x1 port for installation of accessories, e.g. monitor Aluminum buttons and knobs and levers marked in the near with symbols identical to those of the machine in use Wide back display viewfinder glass Viewfinder Dual O-Ring seals on all buttons and removable parts Moisture sensor with LED and audible indicator (replaceable battery) Removable port - 120mm bayonet Ports security latch to prevent accidental opening Wide, rubber covered feet for solid footing M8 hole located on upper side of the housing for various accessories such as focus lights Two M6 holes located on housing bottom side for different accessories such as brackets for strobes or tripods External viewfinders can be mounted, INON compatible

Underwater housing X-2 R6 by INON A housing for Canon EOS R6 INON strobe compatible ultra-accurate multi-functional built-in "TTL Converter" as standard feature Control flash amount directly from camera 12 shots/sec. continuous shooting supported Equipped with “Quick Shoe System” for quick switch between horizontal and vertical camera composition Standard “Vacuum Leak Sensor (PAT. P)" checks housing sealing in only 5 minutes MRS port further evolves to support fine manual focusing Optional two viewfinders provide bright and clear finder image Lightweight and compact ultra-precision cast aluminum body Ultra-accurate multi-functional built-in "TTL Converter"    The "TTL Converter" equipped as a standard feature, triggers INON strobe optically to enjoy fully automatic TTL. Exclusively developed for INON strobe based on its flash protocol to optimize its performance for underwater use. As an underwater strobe manufacturer, we successfully achieved the TTL Converter that provides constant, stable and highly accurate TTL exposure. Strobe manual power is directly adjustable from camera INON strobe manual power is directly adjustable from camera ranging between 1/64 and FULL at 1/3EV. increments. Useful when strobe is positioned away like on long strobe arm or when shooting with backlit technique. 12 shots/sec. continuous strobe firing ***** The TTL Converter fully supports [High speed continuous][High speed continuous+]. With ultra-accurate TTL shooting is now available for continuous shooting based on electricity stored in a capacitor6. INON TTL Converter strives efficiency in battery consumption not to miss precious moment and successfully provides more than 100,000 flash triggering only by two CR2032 coin batteries.   Built-in "Vacuum leak sensor" confirms housing sealing in 5 minutes The "Vacuum Leak Sensor" ensures housing sealing by monitoring air pressure inside of the housing during leak check and warns accidental flooding with LED blinks and buzzer during diving. The onboard pressure sensor changes sensitivity for leak check and diving by variable control program (PAT. P).  The supersensitive pressure sensor detects even fine leakage. Not as like conventional leak sensors, it drastically shortens test time (from 30 seconds to 5 minutes). The sensitivity of the dive mode eliminates false alarm even when ambient temperature changes. New S-MRS Port Newly developed S-MRS (Magnetic Rotary System) controls focusing and zooming by magnetic attraction. The new S-MRS provides smoother operation with less play or rattle comparing to the previous model. By combining the EOS R5 with an RF lens, the MF Peaking function can also be used during full-time manual focusing. Together with the focus guide function, this enables ultra-precise focusing.  Maximum three MRS Control Rings can be installed to control the Control Ring, Focus Ring and SA Control Ring. Lightweight and compact ultra-precision cast aluminum body The X-2 R6 is made from corrosion resistance aluminum alloy by ultraprecise cast manufacturing technique to fuse design, weight and durability in higher dimension. The cast manufacturing technique enables thin body plate with complicated curved design which is not possible with machining. Lightweight and durable aluminum alloy body has acquired reliability, durability and controllability even in severe underwater.

Marelux housing has the industry leading design that’s not only more compact than other brands but also more simplified in mechanical structure to make it easy to assemble. With 125mm port diameter, the biggest in the market, users can easily install and uninstall cameras with large lens through the housing. Marelux housing is built using uniquely anodized aluminum alloy which provides superb scratch resistance, sea water erosion durability as well as the attractive options of various surface colors. The housing maintains a perfect balance between sturdy body and lightweight. It has the best-in-class ergonomics with all the camera controls readily available at your fingertips including AF-ON and Q Menu. The housing front has the EF and RF lens release button which makes the exchanges of EF and RF lens super easy.  Marelux housing can be connected to other innovative products made by Marelux, such as SNAP (Smart Nautical Application Platform), Smart View Finder etc., making diving and underwater photography easier, safer and more enjoyable.   

The latest Canon APS-C mirrorless camera is finally here!  The Canon EOS R7 utilizes Canon's newest RF mount and boasts a 32.5MP CMOS sensor.  Crop-sensor cameras have always been popular with the underwater shooter community and with good reason. Lens choices, size, and weight are just a few of the great features that shooting APS-C cameras has. The EOS R7 gives original Canon 7D and 7D Mark II shooters a great reason to upgrade and Nauticam is ready to help with the NA-R7 housing.   The Canon EOS R7 Camera The Canon EOS R7 is the latest in Canon's APS-C mirrorless camera lineup which has gained unprecedented demand.  It features the RF lens mount which has the same large 54mm diameter but the ability to have larger rear lens elements that are closer to the sensor gives increased corner and outer edge sharpness.  The R7 uses a 32.5MP CMOS sensor with in-body image stabilization which can reduce shake by up to 7 stops.  The camera's Dual Pixel II autofocus system was carried over from the pro body EOS R3 and features 651 automatic AF points covering the entire sensor area.  It is also capable of recording oversampled 4K 30p video using the full 7K area of the sensor, or subsampled UHD 4K up to 60p from the full sensor width.   The Canon EOS R7 can also use the large EF-mount lens lineup via a simple EF to EOS R adaptor.  The Nauticam NA-R7 housing only supports the the standard EF to EOS R adaptor and does give access to the control ring or drop in filter adaptors.   Key features - Canon EOS R7 32.5MP APS-C CMOS sensor with Dual Pixel AF Up to 30 fps shooting (e-shutter), 15 fps with mechanical In-body image stabilization, rated at up to 7 stops Oversampled UHD 4K up to 30p, line-skipped or cropped 4K/60p 10-bit video as 'PQ' true HDR footage or C-Log 2.36M dot OLED viewfinder 1.62M dot fully-articulating touchscreen Twin UHS-II SD card slot Environmental sealing The Canon EOS R7 underwater housing from Nauticam   The NA-R7 underwater housing follows suit with Nauticam's drive for innovation. Like the full frame Canon EOS R5, R5 C and R3, the NA-R7 present shooters with the ability to use both the available legacy EF lenses via an adapter in addition to their native RF optics.  To support both the legacy and native lenses, Nauticam has designed a N100 to N120 adapter which integrates into the N120 Canon EF port system. Canon's EF to RF mount adapters can be affixed to the camera before insertion into the housing. When using the EOS R7 inside the housing with the adapter and a supported EF lens, the port and extension ring arrangement will be identical to the same setup on a Nauticam Canon N120 DSLR. As the RF-S lens lineup emerges, dedicated port and extension ring combinations will be listed on the new N100 RF-S Port Chart.  Mission Control Nauticam engineers are obsessed with getting the underwater image maker unfettered access to all the necessary controls, with as many within easy reach of the ergonomic rubberized handles. This Mission Control philosophy extends to the NA-R7 where a dual thumb lever is placed by the right front side accessing the M-Fn and Record buttons.  On the rear right side is a thumb lever accessing AF-ON. Near the left handle is a thumb lever for "Playback." Large knurled and rubberized control dials access the camera's "main" and "sub" command dials. The two-stage trigger allows for smooth focus and firing activation. Additional buttons for "Menu", "Focus Point Selection" and others are also easily reached from the handles. Flash triggering Flash triggering is achieved via one of two optional Flash Triggers, a manual LED trigger (NA26305) or a TTL Flash Trigger (NA26321) that use the built-in fiber optic bulkheads with optional fiber-optic cables to trigger supported strobes. For controlling strobes that do not support fiber optic flash triggering, a variety of legacy hot-shoe flash control bulkheads are available. Integrated system for vacuum testing and leak detection The Nauticam vacuum check and leak detection electronics are shipped with the NA-R7 as standard equipment. Combined with an accessory vacuum valve (NA25624) this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

THE FUJIFILM GFX 100 II CAMERA The GFX100 II introduces a revolutionary 102-megapixel large-format sensor. With the GFX100 II, you will experience precise subject detection and tracking AF and unparalleled video capabilities never seen in any previous GFX system or X Series camera. Enhanced by upgraded AI-developed autofocus algorithms and a cutting-edge 9.44-million dot EVF, photographers gain unparalleled accuracy. Filmmakers will benefit from full-width 4k/60, 4:2:2 ProRes Video. Key Camera Specifications New 102mp CMOS II HS and X-processor 5 9.44 million dot EVF Full width 4k60 4:2:2 ProRes Multiple Cinema Formats: FUJINON, PREMISTA,35mm, and 35mm Anamorphic  Worlds first: Natively enabled for Frame.io Camera-to-cloud integration with no accessory requirements  The GF-mount lens lineup continues to grow, with more and more lenses meeting the criteria underwater image-makers are after. Paired with the camera's medium-format 102MP sensor, which is 68% larger than a full-frame sensor, the resulting images have lower noise and greater dynamic range for a given exposure value. The GFX100 II features the latest X-Processor 5 chip which powers the improved autofocus system that covers virtually 100% of the image area. The camera's large built-in OLED viewfinder has a 9.44M-dot resolution and features variable refresh rates and resolution to enhance battery life. Video from the GFX100 II uses the full sensor width, preserving the original field-of-view of the lens, and can be recorded internally as 4K 60p video. Over HDMI the GFX100 II can output either an uncompressed 16-bit raw or 10-bit 4:2:2 4K video signal, excellent news for those using external monitors/recorders such as the Atomos Ninja V. With dedicated settings for both still or video modes, switching between shooting modes is quick and easy via a lever atop the camera. The camera's "Q" menu can be customized to provide the most valuable information as either an overlay on the live-view representation or as the entire LCD area. The NA-GFX100II Underwater Housing by Nauticam The NA-GFX100 II is built with the singular focus of creating an underwater housing that blends ergonomic design, intuitive control placement, and rugged field-tested durability. The resulting machined aluminum housing can be further refined with the addition of accessories from magnifying viewfinders to external monitors/recorders. Achieving the full benefit of the stunning 102MP resolution requires the use of underwater optics that are designed with high-resolution lenses in mind to deliver the highest optical quality possible. Mission controll design The NA-GFX100 II is designed with our Mission Control philosophy which dictates placing controls where they are needed most, meaning no more missed shots fumbling for a control or dial. The majority of exposure and focus controls are within easy reach of the ergonomic handles that feature stainless steel stiffening brackets to reduce any unwanted movement even when using large strobes or video lights. A multi-direction pad on the upper right of the rear panel gives access to the camera's joystick. A double lever near the right handle activates the 'AF-ON' and 'Q' controls. Also on the right side are levers for Focus and View modes. Also, a new front lever to quickly switch between aperture and ISO sensitivity. The left side has a double lever for 'PLAYBACK' and 'DISP' as levers for turning the EF-X20 TTL flash on or off and a front double lever to access Fn5 & Fn6. On top of the housing is a lever for switching between 'STILL' and 'VIDEO' modes. Premium proffesional Optics Built around the N120 Port System, the NA-GFX100 II supports a variety of GF-mount lenses with a selection of optical-quality glass and acrylic ports as well as access to Nauticam's lineup of premium professional optics. These optics are designed using industrial lens design software to provide unparalleled optical quality and impressive fields of view. The Wide-Angle Conversion Port 2 or WACP2, when used with the Laowa 17mm f/4 GFX Zero-D lens can achieve an impressive 140º FOV with an almost 0" minimum focus distance and incredible corner sharpness even at wider-open apertures such as f/5.6. Flash Triggering Flash triggering is via the optional 26351 Flash Trigger for Fujifilm and built-in fiber-optic bulkheads. An option for electronic strobe connection without TTL is also possible using the optional M14 Nikonos bulkhead with a universal hot shoe. HDMI Output The GFX100 II can output high-quality uncompressed 4K video over HDMI and the NA-GFX100 II is compatible with the Nauticam HDMI 2.0 system via the front M24 bulkhead. Even when recording video internally, the use of an external monitor over either HDMI 1.4 or 2.0 is a great tool to help with composition or image review. Vacuum Check and Leak detection system The NA-GFX100 II comes with the Nauticam vacuum check and leak detection system as standard equipment. Combined with an optional accessory vacuum valve this monitoring system provides constant updates on the water-tight and safe-to-dive status of the housing. A simple color-coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action-packed dive.

With the GFX100S, Fujifilm has transferred the power of the larger medium-format GFX100 into a smaller camera body that is more in line with a standard mirrorless full-frame cameras while also making various performance improvements.  The GFX100S maintains the 102MP BSI CMOS sensor yet features a smaller and lighter in-body image stabilization system, autofocus points that cover virtually 100% of the image frame and is powered by the X-Processor 4 chip. THE FUJIFILM GFX100S CAMERA Fujifilm's mirrorless medium-format (44mm x33mm sensor size) GFX100S camera packs the expected large 102MP pixel count into a camera body more in-line with a full-frame mirrorless system.  Even while reducing overall camera size, the GFX100S receives a more capable in-body image stabilization (IBIS) system as well as supercharged autofocus driven by the latest X-Processor 4 chip.  Key Camera Specs 102MP BSI CMOS Sensor (44mm x 33mm) IBIS rated at 6EV 4K 30p video at up to 400Mbps with full-width readout Uncompressed 10-bit 4:2:2 or 16-but raw video output over HDMI Dual-gain ISO Up to 16-bit uncompressed raw files The GF-mount lens lineup continues to grow, with more and more lenses meeting the criteria underwater image-makers are after.  Paired with the camera's medium-format 102MP sensor, which is 68% larger than a full-frame sensor, the resulting images have lower noise and greater dynamic range for a given exposure value.  Users can choose to record up to 16-bit uncompressed raw image files, preserving the maximum amount of sensor data for post-processing. The GFX100S features the latest X-Processor 4 chip which powers the improved autofocus system that covers virtually 100% of the image area.  The camera's large built-in OLED viewfinder has 3.69M-dot resolution at 0.77x magnifications and features variable refresh rates and resolution to enhance battery life. Video from the GFX100S uses the full sensor width, preserving the original field-of-view of the lens and can be recorded internally as 4K 30p video with a bit-rate of up to 400Mbps.  Over HDMI the GFX100S can output either an uncompressed 16-bit raw or 10-bit 4:2:2 4K video signal, excellent news for those using external monitors/recorders such as the Atomos Ninja V.   With dedicated settings for both still or video modes, switching between shooting modes is quick and easy via a lever atop the camera.  The camera's "Q" menu can be customized to provide the most valuable information as either an overlay on the live-view representation or as the entire LCD area.   Example-Setup The Nauticam NA-GFX100S Underwater Housing  The NA-GFX100S is built with the singular focus of creating an underwater housing that blends ergonomic design, intuitive control placement and rugged field-tested durability.  The resulting machined aluminum housing can be further refined with the addition of accessories from magnifying viewfinders to external monitors/recorders.  To achieve the full benefit of the stunning 102MP resolution requires the use of underwater optics that are designed with high-resolution lenses in mind to deliver the highest optical quality possible.   Mission Control Design The NA-GFX100S is designed with our Mission Control philosophy which dictates placing controls where they are needed most, meaning no more missed shots fumbling for a control or dial.  The majority of exposure and focus controls are within easy reach of the ergonomic handles that feature stainless steel stiffening brackets to reduce any unwanted movement even when using large strobes or video lights.  A multi-direction pad on the upper right of the rear panel gives access to the camera's joystick.  A double lever near the right handle activates the 'AF-ON' and 'Q' controls.  Also on the right side are levers for Focus and View modes.  The left side has a double lever for 'PLAYBACK' and 'DISP' as as levers for turning the EF-X20 TTL flash on or off and one for the cameras 'V-Fn4' control.  On top of the housing is a lever for switching between 'STILL' and 'VIDEO' modes. Premium Professional Optics Built around the N120 Port System, the NA-GFX100S supports a variety of GF-mount lenses with a selection of optical-quality glass and acrylic ports as well as access to Nauticam's lineup of premium professional optics.  These optics are designed suing industrial lens design software to provide unparalleled optical quality and impressive fields-of-view.  The Wide-Angle Conversion Port 2 or WACP2, when used with the Laowa 17mm f/4 GFX Zero-D lens can achieve an impressive 140º FOV with an almost 0" minimum focus distance and incredible corner sharpness even at wider-open apertures such as f/5.6.   Flash Triggering Flash triggering is via the optional Fujifilm EF-X20 TTL flash and built-in fiber-optic bulkheads.  An option for electronic strobe connection without TTL is also possible using the optional M14 Nikonos bulkhead with universal hot-shoe.   HDMI Output The GFX100S can output high-quality uncompressed 4K video over HDMI and the NA-GFX100S is compatible the Nauticam HDMI 2.0 system via the front M24 bulkhead. Even when recording video internally, the use of an external monitor over either HDMI 1.4 or 2.0 is a great tool to help with composition or image review.  Vacuum Check and Leak Detection System The NA-GFX100S comes with the Nauticam vacuum check and leak detection system as standard equipment. This monitoring system, working in tandem with the pre-installed vacuum valve, provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.  

The X-T5, Fujifilm's latest APS-C mirrorless hybrid camera, adds a list of significant upgrades when compared to its predecessors.  Some of the most noticeable improvements are a new 40.2MP sensor with a processor 2x as fast as the X-T4.  As still/video hybrids become more popular, Fuji is offering a high-resolution camera that can record internal 6.2K 10 bit 4:2:2 video or 12 bit ProRes RAW externally over HDMI in addition to shooting an impressive 20fps of continuous stills. FUJIFILM X-T5 Camera The Fujifilm X-T5 features an APS-C CMOS 4 X-Trans 5 HR BSI 40MP Sensor. The X-T5 is powered by a new X Processor 5 which provides extremely fast performance and improved responsiveness. Improved in-body stabilization delivers up to a 7EV benefit which is a significant benefit for video shooters.  The intelligent 425 point hybrid autofocus tracking system is now sensitive down to -7EV allowing it accurately focus in extreme low light conditions.   The X-T5 allows you to record oversampled 6.2K 30p or 4K 30p with a 1.23x crop factor or subsampled 4K 60p with the full width of the sensor.  When combined with the Atomos Ninja V, the X-T5 can output up to 6.2K 12 bit ProRes RAW.  Like the X-T4, the X-T5 also features HLG and F-Log capture to increase dynamic range, protecting highlights and shadows for editing. New to the X-T5 is F-Log2 which provides you with 13+ stops of dynamic range instead of just 12 stops with F-Log.  Key Camera Specifications 40MP APS-C X-Trans CMOS 5 HR BSI sensor In-body image stabilization up to 7 EV benefit 20 fps shooting with AF (15 fps with mechanical shutter) 3.69M-dot OLED electronic viewfinder 4K 60p, 6.2K 30p 4:2:2 10-Bit Videor Internal F-Log and F-Log2 capture Dual UHS-II SD card slots Two-axis tilt rear screen THE NAUTICAM NA-XT5 UNDERWATER HOUSING Nauticam has supported all the previous X-T cameras and continues to create innovative and ultra-functional housings for this line with the NA-XT5 underwater housing.  The NA-XT5 features DSLR-style housing and port lock mechanisms as well as integrated ergonomic handles. The housing is designed with our Mission Control concept of placing the most important camera controls as close to the handles as possible to facilitate effortless and quick camera operation to ensure you don't miss the shot. The NA-XT5 features thumb levers near both handles, with the left thumb lever actuating the playback function and the right thumb lever the AF-ON control. The housing includes two M14 and one M24 bulkhead openings to accommodate a variety of accessories. The NA-XT5 uses the N100 Port System shared with the Fujifilm XH1, XT3 and XT4 system. A selection of port options are available for a variety of lenses. PREMIUM PROFESSIONAL OPTICS Nauticam's wide range of ports and in-house corrective optics are the perfect compliment to the NA-XT5's inherent flexibility. Built around the N100 Port System, the NA-XT5 supports a wide variety of X-mount lenses. In addition, there are several options available to use the groundbreaking WACP-1 and WACP-C wide-angle corrective lenses as well as the more compact and in-water removable WWL-1B and WWL-C. For example, with the Fuji XF 18-55mm f/2.8-4 R LM OIS lens, the WACP-1 brings the original 75º field-of-view to an impressive 130º with sharper corners, an ~0" minimum focus distance and a more natural looking image than would be provided by a standard glass dome port.  For complete water contact lens compatibility, you can view the port chart here.   HDMI 2.0 A large bore M24 bulkhead is located at the front of the housing for use with HDMI 2.0 or HDMI 1.4 (with a step-down adapter to M16) external monitors and recorders.  The X-T5 can output up to 6.2K 12 bit ProRes RAW over HDMI 2.0.  See the resources sidebar for additional details and recommended setups. FLASH TRIGGERING Reliable automatic flash exposure is available with the NA-XT5 and a variety of optically fired flashes, precisely reproducing the Fujifilm EF-X8 flash at a proportionally greater intensity. This system yields accurate automatic TTL flash performance – even in manual exposure mode – with no electrical sync cables to flood! The NA-XT5 is also compatible with the Nauticam Mini Flash Trigger for Panasonic/Fujifilm (PN 26305). The Flash Trigger allows for rapid fire manual flash firing via fiber optic, with no camera battery drain. The NA-XT5 comes fiber optic ready and accepts standard Sea & Sea style bushing connections. Nauticam Universal fiber optic cable system (PN 26216) for Inon, Sea&Sea strobes, provide exceptional light transmission for accurate TTL performance. External Battery Pack The NA-XT5 housing supports the use of an USB-C battery pack in order to greatly extend the time between battery swaps, and allowing the housing to remain sealed between dives.  The battery compartment at the bottom of the housing supports batteries up to 150mm(W) x 18mm (H) x 72mm (D).  Here is a known compatible battery with more to come: Anker USB-C Portable Charger 10000mAh with 20W Power Delivery, 523 Power Bank (PowerCore 10K).  (180min of additional run time) 25303 USB-C to USB-C Right Angled Cable (in 0.5m length) is recommended for use with USB-C battery packs.   INTEGRATED VACUUM CHECK AND LEAK DETECTION SYSTEM The Nauticam vacuum check and leak detection system is pre-installed in the NA-XT5 as standard equipment. Combined with an optional M14 Vacuum Valve II (PN 25624), this monitoring system provides constant updates throughout the dive as to watertight integrity of the housing via a multi-color LED on the rear of the housing.

Techniques and innovations based on years of experience have resulted in an easy-to-use, highly professional product. Perfect handling of the Nikon D500 housing is made possible by adjustable grips that fit the human hand and make holding the camera very comfortable, even on long dives. Easy access to all important camera controls through clearly labelled, laser-engraved, durable buttons, even with gloves and dry-diving gloves. An easy and quick release camera mounting plate allows camera positioning and a lever locks the compartment inside the housing. The back door has a large scratch-resistant window glass for a fine camera display and optical viewfinder, and is completely separated from the front body to facilitate camera mounting. External viewfinders can be mounted, INON X-2 compatible. Open and close with one hand The housing for the Nikon D500 is locked with Isotta's one-handed, one-turn knob. It is the only single locking mechanism on the DSLR housing market. It's quick, easy and secure thanks to its double steel pins on the underside of the housing. Ports and extensions A range of connectors and extension rings are available in a dedicated section. The detachable port mounts to the Nikon D500 thanks to markers and a 120mm bayonet mount. The interchangeable port bodies and extension rings allow the use of most lenses on the market for maximum versatility and performance. TTL converter included The Nikon D500 housing features TTL converter electronics for automatic flash control. It also offers the possibility of using external flashes via two standard light connectors as well as two optional Nikonos sync cable bulkheads. This allows for easy mounting of all flash and lighting equipment.  Construction and safety Only the best materials are used in the manufacture of our enclosures, such as anodised aluminium, which is corrosion-resistant and thermally coated, and stainless steel. A durable product that requires easy and quick maintenance by the user. So small and so rich in technology! Two high quality O-ring seals protect and ensure perfect and safe waterproofing for all moving and / or removable parts; a red moisture / water alarm inside the housing is powered by a user replaceable battery. The working depth is 100 metres. Various accessories can be mounted by means of an M8 hole on the top of the enclosure and double threaded M6 holes on the bottom of the enclosure. Special features Ergonomic side grips, adjustable (via optional accessories) TTL converter electronics for automatic flash control included in scope of delivery Two fibre optic connectors Two sockets with electrical sync cable Rear housing is completely detachable from the front housing Locking compartment for easy camera mounting One-hand lock for the rear housing One M16 socket for mounting accessories, e.g. vacuum valves or monitors Aluminium buttons and dials with engraved symbols identical to the camera controls All camera controls are external Viewfinder glass with wide back Optical viewfinder Double O-ring seals on all buttons and removable parts Moisture alarm with LED and audible warning (replaceable battery) Removable port - 120mm bayonet Safety lock on ports to prevent accidental opening Wide, rubberised feet for firm footing M8 hole at the top of the housing for various accessories such as focus lamps Two M6 holes on the bottom of the body for various accessories such as flash or tripod mounts External viewfinders can be mounted, INON X-2 compatible

Techniques and innovations based on years of experience have resulted in an easy-to-use, highly professional product. Perfect handling of the Nikon D7500 housing is made possible by adjustable grips that fit the human hand and make holding the camera very comfortable, even on long dives. Easy access to all important camera controls through clearly labelled, laser-engraved, durable buttons, even with gloves and dry-diving gloves. An easy and quick release camera mounting plate allows camera positioning and a lever locks the compartment inside the housing. The back door has a large scratch-resistant window glass for a fine camera display and optical viewfinder, and is completely separated from the front body to facilitate camera mounting. External viewfinders can be mounted, INON X-2 compatible.  Open and close with one hand The housing for the Nikon D7500 is closed with the Isotta one-handed knob. It is the only single locking mechanism on the DSLR housing market. It is quick, easy and secure thanks to its double steel bolts on the underside of the housing. Ports and extension rings A range of connectors and extension rings are available in a dedicated section. The detachable port mounts to the Nikon D7500 thanks to markers and a 120mm bayonet mount. The interchangeable ports and extension rings allow the use of most lenses on the market for maximum versatility and performance. Light The housing for the Nikon D7500 offers the possibility to use external flashes via two standard light connectors as well as two Nikonos sync cable connectors. This allows for easy mounting of all flash and lighting equipment. Construction and safety Only the best materials are used in the manufacture of our enclosures, such as anodised aluminium, which is corrosion-resistant and thermally coated, and stainless steel. A durable product that requires easy and quick maintenance by the user. Two high quality O-ring seals protect and ensure perfect and safe waterproofing for all moving and removable parts; a red moisture/water alarm inside the housing is powered by a user replaceable battery. Working depth 100 metres. Various accessories can be attached using the M8 hole on the top of the housing and the double M6 threaded holes on the bottom of the housing. Special features Ergonomic side handles, adjustable (via optional accessories) Two fibre optic connections Two connections with electrical sync cable The rear housing is completely detachable from the front housing Locking compartment for easy camera mounting One-hand lock for the rear housing One M16 x 1 hole for mounting accessories, e.g. vacuum valves or monitors Aluminium buttons and dials with engraved symbols identical to the camera controls All camera controls are external Viewfinder glass with wide back Optical viewfinder Double O-ring seals on all buttons and removable parts Moisture sensor with LED and audible indicator (replaceable battery) Removable port - 120mm bayonet Safety lock on ports to prevent accidental opening Wide, rubberised feet for firm footing M8 hole at the top of the housing for various accessories such as focusing lights Two M6 holes on the bottom of the body for various accessories such as mounts for flashes or tripods External viewfinders can be mounted, INON X-2 compatible

Techniques and innovations based on years of experience have resulted in an easy-to-use, highly professional product. Perfect handling of the Nikon D810 body is made possible by adjustable grips that fit the human hand and make holding the camera very comfortable, even on long dives. Easy access to all important camera controls through clearly labelled, laser-engraved, durable buttons, even with gloves and dry-diving gloves. An easy and quick release camera mounting plate allows camera positioning and a lever locks the compartment inside the housing. The back door has a large scratch-resistant window glass for a fine camera display and optical viewfinder, and is completely separated from the front body to facilitate camera mounting. External viewfinders can be mounted, INON X-2 compatible.  Opening and closing with one hand The housing for Nikon D810 is locked with Isotta's one-handed one-turn knob. It is the only single locking mechanism on the DSLR housing market. It's quick, easy and secure thanks to its double steel bolts on the underside of the housing. Ports and extension rings A range of ports and extension rings are available in a dedicated section. The detachable port mounts to the Nikon D810 thanks to markers and a 120mm bayonet mount. The interchangeable port and extension rings allow the use of most lenses on the market for maximum versatility and performance. Light The housing for the Nikon D810 offers the possibility to use external flashes via two standard light connectors. This allows easy mounting of all flash and lighting equipment. Connectors for electric flash cables are optionally available. Talk to us! Construction and safety Only the best materials are used in the manufacture of our enclosures, such as anodised aluminium, which is corrosion-resistant and thermally coated, and stainless steel. A durable product that requires easy and quick maintenance by the user. Two high quality O-ring seals protect and ensure perfect and safe waterproofing for all moving and removable parts; a red moisture/water alarm inside the housing is powered by a user replaceable battery. Working depth 100 metres. Various accessories can be attached using the M8 hole on the top of the housing and the double M6 threaded holes on the bottom of the housing. Special features: Ergonomic side handles, adjustable (via optional accessories) Two fibre optic connections Two connections with electrical sync cable The rear housing is completely detachable from the front housing Locking compartment for easy camera mounting One-hand lock for the rear housing One M16 connector for installation of accessories, e.g. vacuum valves or monitors Aluminium buttons and dials with engraved symbols identical to the camera controls All camera controls are external Viewfinder glass with wide back Optical viewfinder Double O-ring seals on all buttons and removable parts Moisture sensor with LED and audible indicator (replaceable battery) Removable port - 120mm bayonet Safety lock on ports to prevent accidental opening Wide, rubberised feet for firm footing M8 hole at the top of the housing for various accessories such as focusing lights; Two M6 threads on the bottom of the body for various accessories such as mounts for flashes or tripods External viewfinders can be mounted, INON X-2 compatible

The Isotta underwater housing for Nikon D850 allows to capitalize on the camera full potential and to capture amazing pictures underwater. Product details Isotta underwater housing for Nikon D850 An easy to use, highly professional product has been created through techniques and innovations gained from years of experience. The perfect handling of the Nikon D850 housing is possible by means of adjustable handles crafted to match the human hand and make holding the camera very comfortable even throughout long dives. Easy access to all key/main camera controls by means of clearly labelled laser-engraved longlasting buttons, even with gloves and drysuit gloves. An easy and quick release camera mounting plate allows the camera positioning and a lever locks the tray inside the housing. The back door has a large window anti-scratch glass for a fine camera display and optical viewfinder view and it is entirely detached from the front body to make easier the camera fitting. External viewfinders can be mounted, INON X-2 compatible.   ONE HAND OPEN/CLOSE The housing for Nikon D850 is closed with Isotta’s single handed one-turn knob. It’s the only single latch closing mechanism in the DSLR housing market. It’s fast, simple and secure thanks to its double steel pins at the bottom of the housing. PORTS AND EXTENSION RING A series of ports and extension rings are available in dedicated section. The removable port is fitted thanks to markers and a bayonet 120 mm connection to the Nikon D850. The interchangeable port bodies and extensions rings combine to allow the use of most of lenses on the market for maximum versatility and performance. TTL CONVERTER FLASH (optional) The housing for Nikon D850 features TTL Converter Electronics for Automatic flash control. It also offers the possibility to use external strobes via two standard optical light ports (trigger not included) as well as two optional Nikonos N5 or S6 sync cord bulkheads. This allows for easy mounting of any strobe and lighting set up. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such anodized aluminum which is anticorodal and thermo-coated and stainless steel. A longlasting product that requires easy and simple maintenance by the user. Dual high-quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. Different accessories can be fitted by means of an M8 hole positioned on the upper side of the housing and double threaded M6 holes located on housing bottom side. Highlights Ergonomic side handles, adjustable (via optional accessory) TTL converter electronics for automatic flash control not included Two fiber optic connectors (included) Two electrical sync cord bulkheads Nikonos N5 or S6 not included Back housing completely detachable from the front housing Tray with lock for an easy fitting of the camera Single-hand closing knob for back housing One M16 hole for installation of accessories, e.g. vacuum valves or monitors Aluminum buttons and dials with engraved symbols identical to camera controls All camera controls are external Wide back display viewfinder glass Optical viewfinder Double O-Ring seals on all buttons and removable parts Moisture alarm with LED and an acoustic warning signal (replaceable battery) Removable port - 120mm bayonet Ports security latch to prevent accidental opening Wide, rubber covered feet for solid footing M8 hole located on upper side of the housing for various accessories such as focus lights Two M6 holes located on housing bottom side for different accessories such as brackets for strobes or tripods External viewfinders can be mounted, INON X-2 compatible

Its superior ergonomic design and standout range of optional accessories help you capture those optimal moments with the best image Quality. Much lighter than previous housings. Using unprecedented precision machining, the dimensions of the housing are similar to those of the camera. In addition, the revised internal design has also helped reduce weight. The MDX-D850 is approximately 11% (350g/12.3oz) lighter than the previous MDX-D810 housing. All the dials have a spring (damper) to prevent slip of the controls All the dials have a spring (damper) to prevent slip of the controls even if the dimensions of the cameras are slightly different or even if gears or other parts wear out to some extent.  Leak Alarm Unit as standard equipment The Leak Alarm Unit, which was previously available as an option, is now included as standard equipment. It is effective not only for early detection of underwater flooding accidents, but also for protection of equipment by checking its waterproof performance before entry. CR2032 lithium battery included. Optical YS Converter/N1 can be built into the housing Optical YS Converter/N1 can be built into the housing Compatible with Optical YS Converter/N1 for MDX housing which converts the camera’s hot-shoeTTL signal to a light signal. Both TTL and manual strobe modes can be used and controlled from the housing using a Fiber-Optic Cable II. * Fiber-Optic Cable ll is required when using the Optical YS Converter. * Serial numbers 124000274 and above are compatible with the Nikon D850. Serial numbers below 124000274 are not compatible. New firmware and/or conversion of the converter will be required. Other Features The Port Lock prevents the port from turning or loosening and the Port Lock lever is specifically located to avoid being unlocked accidentally. The housing is equipped with a lens-lock release button which makes it possible to change lenses easily, without opening the housing. The camera’s diopter adjustment dial can be operated from outside the housing. This feature is useful when two or more people with different eyesight use the housing. Pulling out the Focus/Zoom Dial gives sufficient room inside the housing to easily accommodate larger diameter lenses. All controls have luminescence stickers which glow in dark environment. Equipped with the Optical Viewfinder 0.5x as standard. Other optional viewfinders such as the VF180 1.2x, VF45 1.2x and Optical Viewfinder 0.8x can be used. *When the VF180 1.2x is mounted on the MDX-D850 housing, the lower part of the camera's viewfinder (where the shooting data is displayed) cannot be viewed due to vignetting. Sync Cord 2-pin Connector enables use of conventional hardwired Sync cable (Manual mode only). Accessory port enables use of Leak Sentinel (vacuum sensor). Equipped with two sacrificial zinc diodes (one on the front case and the other on the rear) to prevent electrolysis damage. Built-in leak sensor immediately alerts you to water ingress. Tripod screw mount is located on the centre underside of the housing.

Compact design. Due to the compact design and light weight of the Z7 / Z6 camera, the housing has been adapted accordingly to enhance these features. Compared to the SLR MDX-850 camera body, the MDX-Z7/Z6 is 100g lighter on land.  Ports and lens rings for the MDX series SLR housings can be used. With the FTZ adapter and the ports and lens rings for the MDX series bodies, you can use F-mount lenses. Compatible with the YS optical converter/N1. TTL flash photography possible. An optional optical YS converter, which converts the camera's hot shoe TTL signal into an LED light signal, is compatible with the housing. Manual flash photography is also possible. Designed for F-mount lenses with the FTZ mounting adapter and Z-mount lenses. The focus/zoom gear has two gears, one for F-mount lenses with the FTZ mounting adapter and the other for Z-mount lenses. The MDX-Z7 is designed to accommodate various Z-mount lenses that will be available soon. The upper control panel of the camera is visible. A window for the upper control panel of the camera is also integrated. As the brightness of the camera's upper control panel has increased, visibility is now significantly improved.  The port lock prevents the port from turning or coming loose, and the port lock lever is specially positioned to prevent accidental unlocking. The body is equipped with a lens release button that allows for easy lens changes without opening the body. Pulling out the focus/zoom wheel provides enough space inside the housing to easily accommodate larger diameter lenses. The camera's diopter adjustment knob can be operated from outside the housing. This feature is useful when two or more people with different eyesight use the housing. All controls have luminescent stickers that glow in dark environments. Equipped with the 0.5x optical viewfinder as standard. Other optional viewfinders such as the 0.66x and 0.8x optical viewfinders can be used. When the VF45 and VF180 1.2x are mounted on the body, the corners of the camera's viewfinder cannot be viewed due to vignetting.  The 2-pin sync cable connector allows the use of a conventional hard-wired sync cable (manual mode only). Equipped with two sacrificial zinc diodes (one on the front and the other on the back) to prevent electrolyte damage.

An ergonomic highly professional product entirely Made in Italy that offers the highest quality and enhanced performance underwater. Product details The durable anodized aluminum protects the camera from water and other damaging elements and its stylish, compact and ergonomic design has been specifically created for the breakthrough models of mirrorless Nikon Z7 / Z6. The perfect handling of the Isotta signature-red color Nikon Z7/6 housing is possible by means of adjustable handles crafted to match the human hand and make holding the camera very comfortable even throughout long dives. Easy access to all key/main camera controls by means of clearly labelled laser-engraved longlasting buttons, even with gloves and drysuit gloves. An quick release camera mounting plate allows the camera positioning and a lever locks the tray inside the housing. The back door has a large window anti-scratch glass for a fine camera display and optical viewfinder view and it is entirely detached from the front body to make easier the camera fitting. External viewfinders can be mounted, INON X-2 compatible. ONE HAND OPEN/CLOSE The housing for Nikon Z7 / Z6 is closed with Isotta’s single handed one-turn knob. It’s the only single latch closing mechanism in the DSLR housing market. It’s fast, simple and secure thanks to its double steel pins at the bottom of the housing. PORTS AND EXTENSION RING A series of ports and extension rings are available in dedicated section. The removable port is fitted thanks to markers and a bayonet 120 mm connection to the Nikon Z7 / Z6. The housing has been made on purpose to fit the Nikon FTZ adapter, which does let you use Nikon F-mount lenses on the Z7 – with varying degrees of compatibility. The interchangeable port bodies and extensions rings combine to allow the use of most of lenses on the market for maximum versatility and performance. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such anodized aluminum which is anticorodal and thermo-coated and stainless steel. A longlasting product that requires easy and simple maintenance by the user. Dual high-quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. Different accessories can be fitted by means of one M8 hole positioned on the upper side of the housing and two threaded M6 holes located on housing bottom side. Three M16 x1 threaded holes can be used for different needs such as to accomodate a vacuum. Controls ON/OFF of Nikon Z7 / Z6 Ergonomic camera focusing and shutter button for an easy use with gloves Lens release Rear control panel Upper control panel All controls are available on the housing Highlights Ergonomic side handles, adjustable (via optional accessory) Two fiber optic connections Two optional electrical sync cord bulkheads Back housing completely detachable from the front housing Dedicated REC lever and ISO button Tray with lock for an easy fitting of the camera Single-hand closing knob for back housing Three M16 hole for installation of accessories, e.g. vacuum valves or monitors Aluminum buttons and dials with engraved symbols identical to camera controls All camera controls are external Wide back display viewfinder glass Optical viewfinder Double O-Ring seals on all buttons and removable parts Moisture alarm with LED and an acoustic warning signal (replaceable battery) Removable port - 120mm bayonet Ports security latch to prevent accidental opening Wide, rubber covered feet for solid footing One M8 hole located on upper side of the housing for various accessories such as focus lights Two M6 holes located on housing bottom side for different accessories such as brackets for strobes or tripods External viewfinders can be mounted, INON X-2 compatible

An ergonomic highly professional product entirely Made in Italy that offers the highest quality and enhanced performance underwater. The Nikon Z7 II / Z6 II Underwater Housing by Isotta The durable anodized aluminum protects the camera from water and other damaging elements and its stylish, compact and ergonomic design has been specifically created for the breakthrough models of mirrorless Nikon Z7 / Z6 and Nikon Z7 II / Z6 II. The perfect handling of the Isotta signature-red color Nikon Z7/6 housing is possible by means of adjustable handles crafted to match the human hand and make holding the camera very comfortable even throughout long dives. Easy access to all key/main camera controls by means of clearly labelled laser-engraved longlasting buttons, even with gloves and drysuit gloves. An quick release camera mounting plate allows the camera positioning and a lever locks the tray inside the housing. The back door has a large window anti-scratch glass for a fine camera display and optical viewfinder view and it is entirely detached from the front body to make easier the camera fitting. External viewfinders can be mounted, INON X-2 compatible. ONE HAND OPEN/CLOSE The Isotta underwater housing for Nikon Z7 II / 6 II is closed with Isotta’s single handed one-turn knob. It’s the only single latch closing mechanism in the DSLR housing market. It’s fast, simple and secure thanks to its double steel pins at the bottom of the housing. PORTS AND EXTENSION RING A series of ports and extension rings are available in dedicated section. The removable port is fitted thanks to markers and a bayonet 120 mm connection to the Nikon Z7 II / Z6 II. The housing has been made on purpose to fit the Nikon FTZ adapter, which does let you use Nikon F-mount lenses on the Z7 – with varying degrees of compatibility. The interchangeable port bodies and extensions rings combine to allow the use of most of lenses on the market for maximum versatility and performance. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such anodized aluminum which is anticorodal and thermo-coated and stainless steel. A longlasting product that requires easy and simple maintenance by the user. Dual high-quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. Different accessories can be fitted by means of one M8 hole positioned on the upper side of the housing and two threaded M6 holes located on housing bottom side. Three M16 x1 threaded holes can be used for different needs such as to accomodate a vacuum. Controls ON/OFF of Nikon Z7 II / Z6 II Ergonomic camera focusing and shutter button for an easy use with gloves Lens release Rear control panel Upper control panel All controls are available on the housing Highlights Ergonomic side handles, adjustable (via optional accessory) Two fiber optic connections Two optional electrical sync cord bulkheads Back housing completely detachable from the front housing Dedicated REC lever and ISO button Tray with lock for an easy fitting of the camera Single-hand closing knob for back housing Three M16 hole for installation of accessories, e.g. vacuum valves or monitors Aluminum buttons and dials with engraved symbols identical to camera controls All camera controls are external Wide back display viewfinder glass Optical viewfinder Double O-Ring seals on all buttons and removable parts Moisture alarm with LED and an acoustic warning signal (replaceable battery) Removable port - 120mm bayonet Ports security latch to prevent accidental opening Wide, rubber covered feet for solid footing One M8 hole located on upper side of the housing for various accessories such as focus lights Two M6 holes located on housing bottom side for different accessories such as brackets for strobes or tripods External viewfinders can be mounted, INON X-2 compatible

The Z 7II and Z 6II, Nikon's next generation full-frame mirrorless cameras, offer underwater shooters the same legendary Nikon sensors with improved autofocus and continuous shooting speed performance. The NA-Z7II supports both the Z 7II and Z 6II models and features the larger-bore M28 bulkhead that supports HDMI 2.0 connections needed for the Atomos Ninja V Recorder/Monitor. THE NIKON Z 6II AND Z 7II CAMERAS For many full-frame Nikon shooters the appeal of a mirrorless camera had been tempered by the thought of having to invest in and master a new system by moving to another ecosystem such as Sony. For those awaiting a mirrorless system that utilized Nikon imaging technology and ergonomics, the wait is over. The Z 6II and Z 7II cameras feature an identical body, differing only in their feature sets, an ideal feature when it comes to housing the camera for underwater use.  Each camera also features dual EXPEED 6 image processor to significantly improve autofocus and continuous speed shooting.   Both camera bodies are built around Nikon's Z-mount. With an incredibly wide 55mm mount diameter (17% larger than F-mount) and very short flange distance, the Z-mount is able to offer a maximum aperture of F0.95. While the current range of Z-mount lenses continues to grow, almost the entire line of F-mount lenses is usable with the optional Nikon FTZ Adapter. When using the adapter, even non VR lenses benefit from the camera's in-body stabilization. VR and Z-Mount lenses receive 5-axis stabilization whereas non-VR F-mount lenses have access to 3-axis stabilization. There is also a dedicated e-VR (electronic VR) that combines optical and electronic stabilization for video shooting. Both the Z 6II and Z 7II will be able to capture internal UHD 4K at 60fps or 1080 HD at up to 120fps.  The Z 6II will be able to record 4K/60P early in 2021 through an expected firmware update.  In addition to N-Log, both cameras also feature HLG (hybrid-log gamma for HDR) which work in 10-bit 4:2:2 over HDMI 2.0 to an external recorder such as the Ninja V.   The OLED electronic viewfinder (EVF) of both the Z 6II and Z 7II gives 100% frame coverage at Quad-VGA (3.69M dot) resolution. When triggering external flashes, both cameras feature a 1/200 X-sync shutter speed. THE NIKON Z 7II CAMERA The Z 7II features a high resolution 45.7MP FX-format sensor that can shoot at up to 10FPS. The Z 7II features a wide ISO range of 64-25,600. Autofocus is achieved with 493 on-sensor AF points that cover 90% of the frame and the camera intelligently switches between contrast-detection and phase-detection points to achieve accurate focus regardless of light conditions. KEY CAMERA SPECS: 45.7MP FX Format Sensor with no OLPF 10 FPS continuous shooting 64-25,600 ISO Range UHD 4K 60p recording with 1.08x crop 10bit UHD 4K N-log output via HDMI with start/stop support 5-axis VR stabilization (with Z lenses) 3.69M-dot EVF, 3.2" 2.1M-dot rear screen -3EV focusing with F2.0 lens 1 CFExpress / XQD card slot, 1 UHS-II SD card slot THE NIKON Z 6II CAMERA The Z 6II is equipped with a 24.5MP FX-format sensor capable of up to 14FPS continuous shooting with an ISO range of 100-51,200. Video is currently recorded internally at up to UHD 4K 30p.  UHD 4K 60p with a 1.6x crop will be available in early 2021 through a firmware update. 273 on-sensor focus points cover 90% of the fame and the Z 6II intelligently switches between contrast-detection and phase-detection points to assure accurate autofocus. KEY CAMERA SPECS: 24.5MP FX Format Sensor with OLPF 14 FPS continuous shooting 100-51,200 ISO Range Full Sensor UHD 4K 30p  UHD 4K 60p recording with 1.6x crop (firmware update early 2021) 10bit N-log UHD 4K output via HDMI with start/stop support 5-axis VR stabilization (with Z-mount lenses) 3.6m-Dot OLED Electronic Viewfinder Two card slots (1x CFexpress/XQD, 1x UHS-II SD) THE NAUTICAM NA-Z7II UNDERWATER HOUSING The NA-Z7II underwater housing follows suit with Nauticam's drive for innovation. Both the Nikon Z 6II and Z 7II present shooters with the ability to use both the available legacy F Mount lenses via the FTZ adapter in addition to their native Z Mount optics.  To support both the legacy and native lenses, Nauticam has integrated the NA-Z7II into the N120 port system.  This is critical as the new Z mount lenses are being phased in over the next few years. The Nauticam NA-Z7II housing features two lens release buttons that correspond to either F or Z mount lenses. When switching between F and Z mount lenses, the camera must be removed from the housing to remove the adapter. When working within either the F or Z mount system use the appropriate lens release button to switch lenses without having to remove the camera from the housing. A vacuum system reset switch is located below the tray as well so there is no need to open the rear of the housing during lens or port changes. The NA-Z7II is part of the N120 port system which allows for full support of Nikon F mount lenses with the same ports needed for their application on Nikon SLR housings. As more Z mount lenses become available Nauticam will add supported configurations. INTELLIGENT CONTROL PLACEMENT Nauticam engineers are obsessed with functionality and this is evident in the location of essential controls. Regardless of where the control is located on the camera, the Nauticam housing puts them where you need them to be underwater. For those switching between photo and video modes, an easily reachable switch is located on the right rear of the housing. The right side double thumb lever, easily reached from the right handle features access to the AF-on and Record buttons respectively. Between the double thumb lever and the multi-stage shutter release is an ISO lever allowing quick changes to sensitivity. The left double thumb lever accesses the DISP and Playback controls. The Zoom In and Zoom Out controls, located on the right rear of the camera body is relocated to the left side of the housing to a location more familiar to Nauticam housing users. The switch that allows for switching between the LCD display and the EVF, a crucial and much used control with mirrorless systems is located close to the left handle within easy reach. Front and rear control dials are readily accessible by the familiar large knurled dials at the right handle. The ergonomic housing handles are rubberized and feature stainless steel stiffening brackets to ensure a stable platform when using large strobes or video lights attached to the pre-installed 1" mounting balls. FLASH TRIGGERING The NA-Z7II comes with Nauticam's self powered manual flash trigger preinstalled. The flash trigger plugs into the hot-shoe of the camera and uses LED lights recessed into each of the two optical bulkheads to trigger supported underwater flashes when used with the correct fiber optic connection. The flash trigger is powered by coin cell batteries that provide thousands of flashes per battery. The flash trigger can be upgraded to support TTL triggering (PN 26308 TTL Converter for Nikon). INTEGRATED VACUUM CHECK AND LEAK DETECTION SYSTEM The Nauticam vacuum check and leak detection system is shipped with NA-Z7II as standard equipment. Combined with an accessory M16 vacuum valve (PN 25625), this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur. The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive. PREMIUM PROFESSIONAL OPTICS Optical performance is just as necessary as camera performance and this becomes even more critical given the challenges of filming underwater. The Nauticam NA-Z7II uses the same N120 Port System as the previous NA-Z7 which makes for a seamless transition for those upgrading to the "II." While this system provides exceptional optical-glass and flat port solutions for a wide variety of F and Z Mount lenses, the real power of the Z 6II and Z 7II can be realized using Nauticam's Water Contact Optics. This lineup of dry and wet lenses are conceived using commercial lens-design software to achieve truly unparalleled underwater image quality both for stills and video in both macro and wide-angle situations. The WACP-1 and WACP-2 achieve ultra-wide 130º fields-of-view with reduced distortion over conventional optics while featuring ~0" minimum focus distances, zoom through capabilities and unbeatable corner sharpness at even wide-open apertures such as F5.6. The SMC-1 and SMC-2 macro wet-optics, when used with the Nikon 105mm f/2.8G VR macro lens provide 2x and 4x magnification respectively and the SMC-1 actually provides a resulting image with increased contrast and sharpness than the 105mm lens itself can achieve in air without a magnifier.

State-of-the-art housing for the full-frame mirrorless Nikon Z7II/Z6II/Z7/Z6 camera. Compact, compatible with the Optical YS Converter and ergonomically designed. Compact design The housing of the Z7/6 camera, as well as the Z7/6 II, takes advantage of the compact design and light weight and has been designed accordingly to enhance these features. Compared to the MDX-850 SLR camera body, the MDX-Z7/6 is 100 grams lighter on land. Ports and gears for the MDX series SLR housings can be used. An optional Optical YS Converter which converts the camera’s hot-shoe TTL signal into an LED light signal is compatible with the housing. Manual strobe photography is also possible. Designed for both F mount lenses with the mount adapter FTZ and Z mount lenses. The Focus/Zoom dial has two gears, one for F-mount lenses with the mount adapter FTZ and the other for Z mount lenses. The MDX-Z7 has been designed to take into consideration various Z mount lenses which will soon be available.   Entwickelt für F-Mount-Objektive mit Adapter FTZ und Z-Mount-Objektive. Das Fokus/Zoom-Drehrad hat zwei Zahnräder, eines für F-Mount-Objektive mit dem Anschlussadapter FTZ und das andere für Z-Mount-Objektive. Das MDX-Z7 wurde für die Berücksichtigung verschiedener Z-Mount-Objektive entwickelt, die in Kürze erhältlich sein werden. The camera’s upper control panel can be seen. A window for the camera’s upper control panel is also incorporated. As brightness of the camera’s upper control panel has increased, the visibility is now greatly improved. MDX-Z7? Other Features The Port Lock prevents the port from turning or loosening and the Port Lock lever is specifically located to avoid being unlocked accidentally. The housing is equipped with a lens-lock release button which makes it possible to change lenses easily, without opening the housing. Pulling out the Focus/Zoom Dial gives sufficient room inside the housing to easily accommodate larger diameter lenses. The camera’s diopter adjustment dial can be operated from outside the housing. This feature is useful when two or more people with different eyesight use the housing. All controls have luminescence stickers which glow in dark environment. Equipped with the Optical Viewfinder 0.5x as standard. Other optional viewfinders such as Optical Viewfinder 0.66x,and 0.8x can be used. ?Some vignetting occurs.When the VF45 and VF180 1.2x is mounted on housing, the  corners of the camera's viewfinder cannot be viewed due to vignetting.  Sync Cord 2-pin Connector enables use of conventional hardwired Sync cable (Manual mode only). Equipped with two sacrificial zinc diodes (one on the front case and the other on the rear) to prevent electrolysis damage. Equipped with under guard to protect from scrach. Compatible with Z7 / Z6 cameras by using the included parts 

An ergonomic highly professional product entirely Made in Italy that offers the highest quality and enhanced performance underwater. Isotta's Nikon Z8 Underwater Housing The durable anodized aluminum protects the camera from water and other damaging elements and its stylish, compact and ergonomic design has been specifically created for the breakthrough models of mirrorless Nikon Z8. The perfect handling of the Isotta signature-red color Nikon Z8 housing is possible by means of adjustable handles crafted to match the human hand and make holding the camera very comfortable even throughout long dives. Easy access to all key/main camera controls by means of clearly labelled laser-engraved longlasting buttons, even with gloves and drysuit gloves. An quick release camera mounting plate allows the camera positioning and a lever locks the tray inside the housing. The back door has a large window anti-scratch glass for a fine camera display and optical viewfinder view and it is entirely detached from the front body to make easier the camera fitting. External viewfinders can be mounted, INON X-2 compatible. ONE HAND OPEN/CLOSE The housing for Nikon Z8 is closed with Isotta’s single handed one-turn knob. It’s the only single latch closing mechanism in the DSLR housing market. It’s fast, simple and secure thanks to its double steel pins at the bottom of the housing. PORTS AND EXTENSION RING A series of ports and extension rings are available in dedicated section. The removable port is fitted thanks to markers and a bayonet 120 mm connection to the Nikon Z8. The interchangeable port bodies and extensions rings combine to allow the use of most of lenses on the market for maximum versatility and performance. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such anodized aluminum which is anticorodal and thermo-coated and stainless steel. A longlasting product that requires easy and simple maintenance by the user. Dual high-quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. Different accessories can be fitted by means of one M8 hole positioned on the upper side of the housing and two threaded M6 holes located on housing bottom side. Three M16 x1 threaded holes can be used for different needs such as to accomodate a vacuum. Controls On and off lever of the Nikon Z8 Ergonomic camera focusing and shutter lever, easy to use with gloves Lens release lever Front dial Fn1 lever Fn2 lever Fn3 lever ISO button MODE button BKT button Flash button +/- button Focus mode button Quick release-mode button Zoom knob Port safety lever Movie lever (REC) AF-ON lever Rear dial R Release mode knob I (info) button Menu button AEL button DISP. button Multi-selector Playback, Viewing pictures button Zoom-in (+) button Zoom-out (-) button Qual button WB button Delete button Fn4 button Photo/video selector On/Off Display lever Highlights Ergonomic side handles, adjustable (via optional accessory) Two fiber optic connections standard (to shoot it needs an additional trigger) Three M16 holes and one M28 for installation of accessories, e.g. syncro cords, vacuum valves, monitors Back housing completely detachable from the front housing Tray with lock for the easy insertion of the camera Single-hand closing knob for the back of the housing Aluminum buttons and dials with engraved symbols identical to camera controls Wide back display viewfinder glass Double O-Ring seals on all buttons and removable parts Moisture sensor with LED indicator (replaceable battery) Removable port 120 mm bayonet Ports security latch to prevent accidental opening Wide, rubber covered feet for solid footing on boat floors or sea floor M8 hole located on upper side of the housing for various accessories such as focus lights Two M6 holes located on housing bottom side for different accessories such as brackets for strobes or tripods External viewfinders can be mounted, INON X-2 compatible

The Z8 is arguably the most hotly anticipated full-frame mirrorless camera from Nikon and the first to feature the '8' series badging.  Featuring a high-resolution 45.7MP sensor that will also capture 8K/60p N-RAW video while delivering incredible autofocus and dynamic range.  The Z8's 3690k-dot OLED EVF packs a fast refresh rate for blackout free shooting thanks to the camera's electronic shutter. The Nauticam NA-Z8 is the latest release in the world's finest line of underwater camera housings and builds on the field-proven housings for other Nikon 'Z-series' cameras . Nauticam is the market leader in ergonomics, build quality, and reliability that are built on a foundation of innovative product design and modern manufacturing technology. The NA-Z8 is the ultimate accessory for the powerful Nikon Z8. THE NIKON Z8 The excitement for the Nikon Z8 rivals that of the release of the Nikon D850. Nikon shooters have been eagerly waiting for what this "mini" Z9. The D850 long ruled the Nikon roost for incredible image quality, amazing autofocus and a wide dynamic range all in a high-resolution package.  While the Z6/7 and Z9 have bracketed the spectrum of specs, the Z8 is the system that many D850 shooters have been waiting for. The Nikon Z8 features a 45.7MP stacked CMOS sensor that is delivers incredible still and moving image performance.  The Z8's electronic shutter means true zero blackout continuous shooting when using the camera's EVF and the wide range of autofocus options insure there's the right mode for every situation. For video shooters, the Z8 can capture up to 8K/60p or oversampled 4K/120p internally in their ultra-efficient 12-bit N-RAW format or a variety of ProRes formats including ProRes RAW.  The Z8 also adds pro-level video features such as a waveform monitor, focus peaking, and the ability to fine tune ISO at 1/6EV steps.  There's also a convenient 'Video Info Display' and Red Record Border. Setup example THE NAUTICAM NA-Z8 Underwater Housing The Nauticam NA-Z8 is the most intuitive and reliable underwater housing available for the Nikon Z8.  Building on the successful and field-tested designs for the NA-Z6/7 and Z9 housings the NA-Z8 embodies Nauticam's Mission Control design philosophy placing essential controls within easy reach of the reinforced molded handles. F AND Z MOUNT COMPATIBLE The NA-Z8 underwater housing for the Nikon Z8 utilizes the N120 Port System for Z-mount full-frame lenses. However, the NA-Z8 is also designed to accommodate the use of F-mount lenses, thanks to the FTZ adapter. This allows the same port configuration as found on an F-mount DSLR system like the NA-D6 or NA-D850. The NA-Z8 housing is equipped with convenient lens release buttons for both F and Z mounts, making lens changes a breeze, regardless of the lens platform. You can quickly and easily switch between different lenses without having to remove the camera from the housing, except when installing or removing the FTZ adapter. ENHANCED VIEWFINDERS Electronic viewfinders are constantly achieving higher resolution and better dynamic range and the Z8 features a 3690k-dot OLED 0.5" viewfinder.  Pair the Z8's EVF with Nauticam's Full Frame Enhanced Viewfinders for unrestricted viewing of the entire EVF in either a straight or angled configuration.  The added working distance from the back of the housing makes for a more comfortable and natural position underwater.  Edge to edge visibility and a dioptric adjustment make for easier composition and tack-sharp focus. PREMIUM PROFESSIONAL OPTICS Nauticam's lineup of optics insure the sharpest, most natural looking images underwater whether it's super-macro or wide-angle.  The WACP-1 Wide Angle Conversion Lens works flawlessly with the Nikkor Z 28-75mm f/2.8 lens to deliver an impressive 130º field-of-view at 28mm and 83º at 48mm.  A ~0" minimum focus distance and small front element makes composition and lighting even easier. Those looking for a more compact system can use the new WACP-C with the Sony SEL2870 28-70mm f3.5-5.6 OSS lens plus the Megadap ETZ 21 adapter which delivers full zoom through and a 130º to 59º field-of-view. Want greater than 1:1 magnification with unmatched sharpness?  The SMC-1 and SMC-2 provide 2.2x and 3.6x magnification respectively with the Nikkor Z MC 105mm f/2.8 VR S Macro lens and can be easily mounted with the Nauticam flips system allowing for fast deployment as well as secure and accurate placement of the optic. HDMI OUTPUT The Nikon Z8 promises clean full-resolution HDMI output using an HDMI type A connector and the NA-Z8 features an M24 bulkhead that can accommodate an HDMI 2.0 connection to a monitor/recorder such as the Atomos Ninja5+ in the NA-Ninja5 housing.  INTEGRATED VACUUM CHECK AND LEAK DETECTION SYSTEM The Nauticam vacuum check and leak detection system is shipped with NA-Z8 as standard equipment. Combined with an accessory vacuum valve (NA25624), this monitoring system provides constant updates on the water tight and safe-to-dive status of the housing. A simple color coded LED lighting system lets the user know that the vacuum is solid, or that the housing is losing vacuum. Leak detection is built into the same circuit, so if there is water intrusion, an audible and visual indication will occur.The Nauticam system is temperature compensated, eliminating false alarms caused by a change in outside temperature, or from a camera heating up on an action packed dive.

An ergonomic highly professional product entirely Made in Italy that offers the highest quality and enhanced performance underwater. Isotta's Nikon Z9 Underwater Housing The durable anodized aluminum protects the camera from water and other damaging elements and its stylish, compact and ergonomic design has been specifically created for the breakthrough models of mirrorless Nikon Z7 / Z6. The perfect handling of the Isotta signature-red color Nikon Z7/6 housing is possible by means of adjustable handles crafted to match the human hand and make holding the camera very comfortable even throughout long dives. Easy access to all key/main camera controls by means of clearly labelled laser-engraved longlasting buttons, even with gloves and drysuit gloves. An quick release camera mounting plate allows the camera positioning and a lever locks the tray inside the housing. The back door has a large window anti-scratch glass for a fine camera display and optical viewfinder view and it is entirely detached from the front body to make easier the camera fitting. External viewfinders can be mounted, INON X-2 compatible. ONE HAND OPEN/CLOSE The housing for Nikon Z7 / Z6 is closed with Isotta’s single handed one-turn knob. It’s the only single latch closing mechanism in the DSLR housing market. It’s fast, simple and secure thanks to its double steel pins at the bottom of the housing. PORTS AND EXTENSION RING A series of ports and extension rings are available in dedicated section. The removable port is fitted thanks to markers and a bayonet 120 mm connection to the Nikon Z9. The housing has been made on purpose to fit the Nikon FTZ adapter, which does let you use Nikon F-mount lenses on the Z7 – with varying degrees of compatibility. The interchangeable port bodies and extensions rings combine to allow the use of most of lenses on the market for maximum versatility and performance. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such anodized aluminum which is anticorodal and thermo-coated and stainless steel. A longlasting product that requires easy and simple maintenance by the user. Dual high-quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. Different accessories can be fitted by means of one M8 hole positioned on the upper side of the housing and two threaded M6 holes located on housing bottom side. Three M16 x1 threaded holes can be used for different needs such as to accomodate a vacuum. Controls On and off lever of the Nikon Z9 Ergonomic camera focusing and shutter lever, easy to use with gloves Lens release lever Front dial Fn1 lever Fn2 lever Fn3 lever ISO button MODE button BKT button Flash button +/- button Focus mode button Quick release-mode button Zoom knob Port safety lever Movie lever (REC) AF-ON lever Rear dial R Release mode knob I (info) button Menu button AEL button DISP. button Multi-selector Playback, Viewing pictures button Zoom-in (+) button Zoom-out (-) button Qual button WB button Delete button Fn4 button Photo/video selector On/Off Display lever Highlights Ergonomic side handles, adjustable (via optional accessory) Two fiber optic connections standard (to shoot it needs an additional trigger) Three M16 holes and one M28 for installation of accessories, e.g. syncro cords, vacuum valves, monitors Back housing completely detachable from the front housing Tray with lock for the easy insertion of the camera Single-hand closing knob for the back of the housing Aluminum buttons and dials with engraved symbols identical to camera controls Wide back display viewfinder glass Double O-Ring seals on all buttons and removable parts Moisture sensor with LED indicator (replaceable battery) Removable port 120 mm bayonet Ports security latch to prevent accidental opening Wide, rubber covered feet for solid footing on boat floors or sea floor M8 hole located on upper side of the housing for various accessories such as focus lights Two M6 holes located on housing bottom side for different accessories such as brackets for strobes or tripods External viewfinders can be mounted, INON X-2 compatible

THE NIKON Z9 MIRRORLESS FULL FRAME CAMERA Nikon's Z9 takes a divergent step from similar top-level mirrorless full frame systems from Sony and Canon by removing the mechanical shutter altogether. This departure, along with the powerful processor allow for the true no-blackout or 'Real-Live" electronic viewfinder (EVF). With a maximum 3,000nit brightness, the EVF promises an even more natural viewing experience similar to an optical viewfinder. The 'F3' button comes pre-set to remove all overlay data from the EVF for an unobstructed composition-focused workspace.  The Z9 is built around a 45.7MP stacked CMOS sensor with exceptional low light performance and 14-bit raw image capture.  The ISO range of the Z9 is 64 to 25,600 with expansion possible to 32-102,400.  The EXPEED 7 processor features advanced noise reduction to maximize image quality at even higher ISO values. AUTOFOCUS Nikon's autofocus has seen dramatic improvement with the Z series and Z9 continues that evolution with AF that works all the way down to -8.5EV (with supported lenses) and features advanced 3D subject tracking. Furthermore, the subject detection system can be set to auto-select the subject type such as animals or people. With over 400 points into auto-detect area, this is sure to deliver exceptional tracking across the frame. 8K VIDEO The EXPEED 7 processor also allows for 8K UHD 30p internal recording with advanced heat dissipation to prevent overheating with an 8K/60P Raw recording firmware update coming in 2022. 10-bit 4K UHD can also be recorded with full pixel readout or with a 2.3x crop factor, exceptional for getting even more macro magnification. The future firmware update will add 12-bit 8K/60p in either Nikon's RAW format or ProRes RAW HQ.  Internal recording is available in either H.265 (8-bit), H.265 (8,10-bit) or ProRes HQ 422 (10-bit) formats to support different workflows.  The Z9 is equipped with dual CFexpress Type-B card slots that also accommodate XQD media. THE NAUTICAM NA-Z9 UNDERWATER HOUSING The Nauticam NA-Z9 brings embodies the experience gained by producing professional housings for Nikon's flagship DSLR and mirrorless cameras, blending them to create the most intuitive underwater imaging platform available. F AND Z MOUNT COMPATIBLE The NA-Z9 uses the N120 Port System for Z-Mount full-frame lenses. When using F-mount lenses, the FTZ adapter is inside the housing which allows for the same port configuration as is found on an F-mount DSLR system such as the NA-D6 or NA-D850. Convenient lens release buttons on the housing for both F and Z mount makes lens changes a snap regardless of platform without having to remove the camera from the housing; only when installing or removing the FTZ adapter. MISSION CONTROL Essential control are placed within easy reach of the ergonomic handles and easy setup means more time in the water and less time working on your rig. Within easy reach of the ergonomic left handle are finger-actuated levers for the customizable 'Fn1' and 'Fn2' buttons as well as the AF-Mode button. A double thumb lever triggers the PLAYBACK and DISP buttons. On the right side is a double thumb lever for the AF-ON and REC control as well as recessed lever for ISO and a forward placed lever for the 'Fn1' button. HDMI OUTPUT As a true hybrid shooting platform the NA-Z9 is just as comfortable being outfitted to capture video as stills. External monitors and recorders can easily be connected via the large M24 bulkhead which supports both HDMI 1.4 and HDMI 2.0 connections. PREMIUM PROFESSIONAL OPTICS The NA-Z9 is built around the extensive N120 Port System that supports a wide range of F-Mount and Z-Mount lenses with a variety of acrylic and optical-glass port options. In addition to standard ports, Nauticam's premium professional water-contact optics deliver the highest possible underwater image quality. The WACP-2, when used with the Nikon Z 14-24mm lenses provides a stunning rectilinear 140º field-of-view and full zoom-through capability with an incredibly natural looking image when compared to a standard rectilinear lens and dome port combination. HDMI Output Required for HDMI 2.0 System NA25086 M24 adaptor for HDMI 2.0 cable (incl. tightening tool) NA25099 M24A2R200-M28A1R170 HDMI 2.0 Cable (for NA-a1 to use with Ninja V housing) Required for HDMI 1.4 System NA25033 Standard HDMI bulkhead with M16 thread* NA25081 M24-M16 Step Down Adaptor NA25100 HDMI (D-A) 1.4 Cable in 200mm length for NA-a1 (for connection from HDMI bulkhead to camera) Compatible Monitor Mounting System NA17951 Nauticam Atomos Shogun housing mounting system NA17954 Tripod plate for NA-A7S and NA-GH4 NA17957 Nauticam Atomos Shogun Housing Mounting Adaptor for NA-S1R/S1H/BMPCC/E2F/R3/Z9(SN from A439736) NA17960 Universal Quadra-Pod Plate for Nauticam Housings

The housing for Olympus OM-D E-M1 Mark II allows to capitalize on the camera full potential and to capture amazing pictures underwater. Product details An easy to use highly professional product has been created through techniques and innovations gained from years of experience. Easy access to all key/main camera controls, even with gloves, by means of clearly labelled lasered long life buttons. The back door has a large window glass for a fine camera display and optical viewfinder view and it is entirely detached from the front body to make easier the camera fitting. The housing stands with great stability due to sturdy and wide rubber feet located on the bottom. Ergonomic side handles are included. ONE HAND OPEN/CLOSE It's very easy to open and close Olympus OM-D E-M1 Mark II, without efforts by the user thanks to the upper helicoid and the bottom centered pins; the camera is placed easily into the housing on a sliding tray that keeps the camera robustly in place. PORTS AND EXTENSION RING A series of ports and extension rings are available in dedicated section. The removable port is fitted thanks to markers and a bayonet 102 mm connection to the Olympus OM-D E-M1 Mark II housing. The interchangeable port bodies and extensions rings combine to allow the use of most of lenses on the market for maximum versatility and performance.  LIGHTING Two fiber optic connections are placed in front of the built-in flash and allow the use of external strobe. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such as anodized aluminum, which is anticorodal and thermo-coated, and stainless steel. A longlasting product that requires easy and simple maintenance by the user. Dual high precision and quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. Different accessories can be fitted directly on the handles or by means of an M8 upper threaded hole, using the Isotta top handle or via the M6 and M8 threaded holes on the bottom. Controls ON/OFF of Olympus OM-D E-M1 Mark II; Own camera strobe open/close; Ergonomic camera focusing and shutter button for an easy use with gloves; Lens release; Rear control panel; Upper control panel; All controls are available on the housing;

The housing for Olympus OM-D E-M1 Mark III allows to capitalize on the camera full potential and to capture amazing pictures underwater. Product details An easy to use highly professional product has been created through techniques and innovations gained from years of experience. Easy access to all key/main camera controls, even with gloves, by means of clearly labelled lasered long life buttons. The back door has a large window glass for a fine camera display and optical viewfinder view and it is entirely detached from the front body to make easier the camera fitting. The housing stands with great stability due to sturdy and wide rubber feet located on the bottom. Ergonomic side handles are included. ONE HAND OPEN/CLOSE It's very easy to open and close Olympus OM-D E-M1 Mark III, without efforts by the user thanks to the upper helicoid and the bottom centered pins; the camera is placed easily into the housing on a sliding tray that keeps the camera robustly in place. PORTS AND EXTENSION RING A series of ports and extension rings are available in dedicated section. The removable port is fitted thanks to markers and a bayonet 102 mm connection to the Olympus OM-D E-M1 Mark III housing. The interchangeable port bodies and extensions rings combine to allow the use of most of lenses on the market for maximum versatility and performance.  LIGHTING Two fiber optic connections are placed in front of the built-in flash and allow the use of external strobe. CONSTRUCTION AND SAFETY Only the best materials are used to manufacture our housings such as anodized aluminum, which is anticorodal and thermo-coated, and stainless steel. A longlasting product that requires easy and simple maintenance by the user. Dual high precision and quality O-Ring seals protect and ensure a perfect and secure watertight for all movable and / or removable parts; a red alarm for humidity/water inside the housing is powered by a battery replaceable by the user. Working depth is 100 metres. Different accessories can be fitted directly on the handles or by means of an M8 upper threaded hole, using the Isotta top handle or via the M6 and M8 threaded holes on the bottom. Controls ON/OFF of Olympus OM-D E-M1 Mark III; Own camera strobe open/close; Ergonomic camera focusing and shutter button for an easy use with gloves; Lens release; Rear control panel; Upper control panel; All controls are available on the housing;